
1.規格型號和安規認證 MODEL NUMBER AND SAFETY CERTIFICATION 1-1 品名規格:系列號+額定電流+額定電壓+認證符號 Model Number: Part Number+Rated Current+Rated Voltage+Approvals. 例子[example]: 630/32GFU 1A 250V 1)系列號 Part Number 2)額定電流 Rated Current 1) 2) 3) 3)額定電壓 Rated Voltage 1-2 額定電流和額定電壓 Rated Current And Voltage 額定電流: 1A~30A Rated Current: 63mA~30A 額定電壓;32V/250V AC/DC Rated Voltage:32V/250V AC/DC 1-3標示Marking 保險絲上需有下列標示 The fuse shall have the following marking: 規格:特性符號+額定電流+額定電壓 Specification:Characteristic Symbol+Rated Voltage 1A~30A:_A250V Trade mark:The Manufacture’s Logo+Part Number+Approvals  
1A~30A: 注意:對標示字樣大小沒有規定 Note:Size of the markings have not be specified. 2.適用範圍 SCOPE 適用於一般電子設備。Used in electronic equipment. 3.工程圖和結構 OUTLINE DRAWING AND STRUCTURE 3-1 工程圖(單位:mm) Outline Drawing and Dimensions(Unit:mm) 
3-2結構 Structure 編號 No. | 元件 Component | 材質 Material | 數量 Quantity | (1) | 熔絲 Wire | 合金 Alloy | 1 | (2) | 銅帽 Cap | 黃銅鍍鎳 Brass with mickel plated | 2 | (3) | 本體 Body | 玻璃管 Glass Tube | 1 | (4) | 引線 Lead | 鍍錫銅線 Tinned Copper wire | 2 |
4.外觀及形狀 APPEARANCES AND CONFIGURATION 4-1外觀:不應有破碎、明顯的汙斑 Appearances:There shall no fragmentation and of remarkable blotch. 4-2形狀:帶腳的保險絲 Configuration:Axial Leaded Fuse. 5.物理特性 PHYSICAL CHARACTERISTIC 5-1 拉力測試 Tensile test 沿端子的軸向施加10N的拉力,持續1分鐘。 Keep pulling the cap of the fuse with 10N at axial direction for 1 min. 6.電氣特性 ELECTRICAL CHARACTERISTICS 熔斷/電流特性: Pre-Arcing Time/Current Characteristic a、Electrical characteristics | Rated current | 135% | 200% | 1000% | 1A~30A | Max. | Max. | Min. | 1 hour | 120 sec | 10 ms |
7.環境特性 ENVIRONMENTAL SPECIFICATION 7-1 操作溫度範圍:-5℃~60℃ Operating Temperature: -5℃~60℃ 7-2 保存條件 Storage Conditions 溫度:+10℃~60℃ Temperature: +10℃~60℃ 在相對濕度≤75%下平均可存放3年 On average, It can be stored below the relative humidity or 75% for 3 years. 在非露天下,相對濕度為95%下最多可存放30天。 Without dew, It can be kept under humidity of 95% for 30 days. 8.焊接條件 SOLDERING PAAMETERS 8-1波峰焊 Wave Solder 焊接溫度:260±5℃ Soldering Temperature:260±5℃ 焊接時間:4 Sec. Max. Soldering Time:4 Sec.Max. 8-2手工焊錫 Manual Solder 焊接溫度:350±5℃ Soldering Temperature: 350±5℃ 焊接時間:3 Sec. Max. Soldering Time: 3 Sec. Max. 9.其他使用注意事項 OTHER NOTICE IN USING 如果需在保險絲上加熱縮套管,烘烤溫度與時間需參照以下規定 If heat shrink tubing was needed,the roast temperature and time should be refer to the following. 設定烘烤溫度:不大於150℃ 烘烤時間:50s Max. The temperature should be sel under 150℃,roast time:50s Max. |