CJ19系列切换电容器接触器 主要用于交流50Hz或60Hz、额定工作电压至400V的电力线路中,供低压无功功率补偿设备投入或切除低压并联电容器之用。接触器带有抑制涌流装置,能有效地减小合闸涌流对电容的冲击和抑制开断时的过电压。


| 1.适用范围 CJ19系列切换电容器接触器(以下简称接触器) 主要适用于交流50/60Hz、额定工作电压至380V的电力线路中,供低压无功率补偿设备投入或切除低压并联电容器之用。接触器有抑制涌流装置,能有效地减少合闸涌流对电容的冲击和抑制开断时的过电压。 |
2.型号及其含义 |
![]() |
3.结构特征 |
![]() |
| 4.特性 |
![]() |
CJ19系列切换电容器接触器适用于交流50Hz或60Hz,电压至380V的电力线路中,供低压无功功率补偿设备投入切换低压并联电容器之用。接触器带有抑制涌流装置,能有效地减少合闸涌流对电容器的冲击和抑制断开的过电压。
用途 CJ19—25,32,43,63型切换电容器接触器,专用于投切低压并联电容器,广泛应用于交流50HZ,电压到380V的无功功率补偿设备中,接触器附有抑制涌流装置,能有效的减少合闸涌流对电容器的冲击和降低开断瞬间的操作过电压,可代替原来由一只接触器和三只限流电抗器组成的切换装置,体积小,重量轻,通断能力强,安装方便。 Application Type CJ19—25,32,43,63 capacitchangeover contactis especially used flow voltage shunt capacitswitching. it widely used in reactive power compensation equipment in which AC 50HZ, voltage 380V, inrush current system in the contactcan decrease shock to capacitlower switching overvoltagein while breaking a circuit.Moreover, It can replace transfer device which are composed of one contactthree current limiting reactors, small, light,s convenient reliable, hige capacity of turning on/off. 使用条件 海拔高度:不超过2000M 周围空气温度:-5℃~+40℃ 相对湿度:+25℃时不大于90% 空气中无导电尘埃和腐蚀金属的气体 安装面与垂直面的倾斜度不大于5° Working conditions Sea level height:at most 2000M Ambient air temperature: -5℃~+40℃ Relative humidity (RH): When +25℃,it should be less than 90% No inductive dust gas of corroding metal in air Installation conditions: degree of inclination between fitting surface vertical surface should be less than ±5 型号规格: CJ:切换电容接触器 19:设计序号 —:基本规格,以约定发热(A)表示 —:辅助触头组合 Types specifications CJ:capacitchangeover contactor 19:design sequence —:basic size,using conventional heating(A)to show —:auxiliary contact block 主要技术参数:Main Technical Parameter 型号:model 项目:item 额定绝缘电压:rated insulation voltage 额定工作电压:rated operational voltage 可控容量: controllable capacity 约定交热电流:conventional heating current 额定工作电流:rated operational current 控制涌流能力:controlling inrush currentcapacity 控制电源电压:controlling supply voltage 线圈工作范围:coil working range 吸合:making 释放:release 操作频率:operating frequency 电寿命万次:Electric life 104 times 机械寿命万次:mechanical life 104 times 外形尺寸及安装尺寸:outline installing dimensions 内部电路连接 接触器除可用螺钉安装外,亦可采用标准卡轨快速嵌入方式安装。对CJ19-25,32,43接触器,卡规宽度35mm,对CJ19-63接触器,卡规宽度35mm或75mm inter-connection circuit This contactcan use not onlyscrew to mount,but alsostandard rail to mount. FCJ19-25,32,43 contactor,the rail width is 35mm.FCJ19-63 contactor,the rail width is 35mm 75mm 使用与维护 接触器的进线和出线多必须连接牢固,以免因压接松动而造成接线端过热而烧毁端子和产品。 接触器闭合时,合闸涌流较大,电阻可能被烧坏,此时应在更换电阻后才能继续使用。 功率因数补偿设备中的放电装置所选的电器,其绝缘电压应大于Ue Operation maintenance The inlet outlet wire of contactshould be connected firmly inder to avoid terminal product burned down. When contactcloses, inrush current turns higher, resistance is easy to be burned down,then you should change resistance to continue to use Isolation voltage of the electric discharge parts in power factcompensation device should be no less than Ue |