Dataman 448Pro2 Super Fast Gang ISP Production Programmer
Super fast universal gang programmer with four independent 48-pin ZIF sockets, ISP capabilities and USB 2.0 connectivity. Independent programming options combine with device insertion tests and a user friendly interface to give higher programming yields and reduced failure rates.
The 448Pro2 is built to meet the demands of high volume production programming with minimal operator effort.
General
448Pro2 programmer offers the same advanced features as 448Pro+ programmer but with much higher programming speeds (20-75%) for high-capacity memories.
Independent programming is more efficient than the concurrent programming method used in traditional gang programmers as each site operates independently allowing programming to start as soon as each device is inserted into the ZIF socket. Before the last device is loaded, the first device is already programmed and ready for removal. The operator is always busy removing and inserting chips, so both the operator and programmer are running continuously at maximum efficiency. With traditional gang programmer operation, the operator is idle while chips are being programmed and the programmer is idle while chips are being removed and new chips inserted. Therefore for the medium programming times, you can easily achieve the throughput of an eight socket gang programmer with one 448Pro2 programmer.
FPGA based totally reconfigurable 48 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Pin drivers operate down to 1.8V so you'll be ready to program the full range of today's advanced low-voltage devices.
Each programming module performs device insertion tests and contact checks before it programs each device. These capabilities, supported by overcurrent protection and signature-byte check help prevent chip damage due to operator error.
The selftest capability allows diagnostics included in the software to thoroughly check the health of the programmer.
Built-in protection circuits eliminate damage of the programming module and/or programmed device due to environment or operator failure. All ZIF socket pin inputs of the Dataman 448Pro2 programmer are protected against ESD up to 15kV.
Dataman 448Pro2 programmer performs programming verification at the marginal level of supply voltage, improving yield and guarantees long data retention.
Various socket converters are available to handle device in PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP, TQFP, QFN (MLF), SDIP, BGA and other packages.
Programmer Specification
4 x universal programming modules (4 x 48-pin DIL ZIF sockets and 4 x ISP connectors)
Operation result LEDs, LED power
USB 2.0 high-speed compatible port
Protection against surge and ESD on power supply input
Banana jack for ESD wrist strap connection
Banana jack for connection to ground
Module Specification
Base Unit (DAC)
On-board intelligence: powerful microprocessor and FPGA based state machine
Three D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall time
VCCP range 0..8V/1A
VPP1, VPP2 range 0..26V/1A
Selftest capability
ZIF Socket
48-pin DIL ZIF socket accepts both 300/600 mil devices up to 48-pin
Pindrivers: 48 universal
VCCP/VPP1/VPP2 can be connected to each pin
Perfect ground for each pin
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins
Analog pindriver output level selectable from 1.8V up to 26V
Current limitation, overcurrent shutdown, power failure shutdown
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV contact)
Continuity test: each pin is tested before every programming operation
ISP Connector
20-pin male type with missinsertion lock
6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all (including low-voltage) devices
1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins
Programmed chip voltage (VCCP) with both source/sink capability and voltage sense
1x VPP voltage (range 2V..25V/50mA), can be applied to six pins
Target system supply voltage (range 2V..6V/250mA)
ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV air, 8kV contact)
Two output signals, which indicate state of work result = LED OK and LED Error (active level: min 1.8V)
Input signal, switch YES! equivalent (active level: max. 0.8V)
