Dataman 48Pro+ Universal ISP Programmer

Universal 48-pin chip programmer with ISP capabilities and USB 2.0 connectivity. Dataman 48Pro+ can program without the need for a family-specific module, giving you the freedom to choose the optimal device for your design.

The 48Pro+ is built to meet the demands of development labs and field engineers for universal programming.

General

FPGA based totally reconfigurable 48 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Pin drivers operate down to 1.8V so you'll be ready to program the full range of tomorrows advanced low-voltage devices.
The programmer performs device insertion and contact tests before programming each device. These capabilities, supported by overcurrent protection and signature-byte check help prevent chip damage due to operator error.
The selftest capability allows diagnostics included in the software to thoroughly check the health of the programmer.
Built-in protection circuits eliminate damage to the programmer and/or programmed device due to environment or operator failure. All the inputs of the 48Pro+ programmer, including ZIF socket, connection to PC and power supply input are protected against ESD up to 15kV.
48Pro+ programmer performs programming verification at the marginal level of supply voltage, improving programming yield and guarantees long data retention.
Various socket converters are available to handle device in PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP, TQFP, QFN (MLF), SDIP, BGA and other packages

Programmer Specification

1 x universal programming module (1 x 48-pin DIL ZIF socket and 1 x ISP connectors)
Operation result LEDs, LED power
USB 2.0 high-speed compatible port
FPGA based IEEE 1284 slave printer port
Protection against surge and ESD on power supply input and parallel port connection
Banana jack for ESD wrist strap connection
Banana jack for connection to ground

Module Specification

Base Unit (DAC)

On-board intelligence: powerful microprocessor and FPGA based state machine
Three D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall time
VCCP range 0..8V/1A
VPP1, VPP2 range 0..26V/1A
Selftest capability

ZIF Socket

48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices up to 48-pin
Pindrivers: 48 universal
VCCP/VPP1/VPP2 can be connected to each pin
Perfect ground for each pin
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins
Analog pindriver output level selectable from 1.8V up to 26V
Current limitation, overcurrent shutdown, power failure shutdown
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV contact)
Continuity test: each pin is tested before every programming operation

ISP Connector

20-pin male type with missinsertion lock
6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all (low-voltage including) devices
1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins
Programmed chip voltage (VCCP) with both source/sink capability and voltage sense
1x VPP voltage (range 2V..25V/50mA), can be applied to six pins
Target system supply voltage (range 2V..6V/250mA)
ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV air, 8kV contact)
Two output signals, which indicate state of work result = LED OK and LED Error (active level: min 1.8V)
Input signal, switch YES! equivalent (active level: max. 0.8V)