产品名称：工程机械专用高压钢丝编织胶管产品结构：胶管由内胶层、中胶层、一层钢丝编织和外胶层组成产品用途：适于输送液压流体如醇、液压油、燃油、润滑油、水、乳化液、烃等，以实现流体高压输送或液压动力传递。工作温度：-40℃ —+100℃胶管规格内径(mm)钢丝层外径(mm)胶管外径(mm)工作压力(Mpa)检测压力(Mpa)爆破压力(Mpa)最小弯曲半径(mm)参考重量kg/m内压-层数-压力minmaxminmaxminmaxMpaPsiMpaPsiMpaPsi5-1-214.55.48.910.111.913.521.0304342.0608684.012172900.256.3-1-206.16.910.611.715.116.720.0289840.0579680.0115921000.348-1-17.57.78.512.113.316.718.317.5253635.0507070.0101431150.4110-1-169.310.114.515.719.120.616.0231832.0463764.092741300.4712.5-1-1412.313.517.519.122.223.814.0202928.0405756.081141800.6716-1-10.515.416.720.622.225.427.010.5152121.0304342.060862050.7119-1-918.619.824.626.229.431.29.0130418.0260836.052162400.8422-1-821.82327.829.432.534.18.0115916.0231832.046372800.9525-1-725.026.432.534.136.939.37.0101414.0202928.040573001.0932-1-4.431.33339.341.744.547.64.46388.8127517.625504201.3838-1-3.537.739.345.648.050.854.03.55077.5101414.020295001.8051-1-2.650.452.058.761.965.168.32.63775.275310.415076302.80产品名称：工程机械专用高压钢丝编织胶管产品结构：胶管由内胶层、中胶层、两层钢丝编织和外胶层组成。产品用途：适于输送液压流体如醇、液压油、燃油、润滑油、水、乳化液、烃等，以实现流体高压输送或液压动力传递。工作温度：-40℃ —+100℃胶管规格内径(mm)钢丝层外径(mm)胶管外径(mm)工作压力(Mpa)检测压力(Mpa)爆破压力(Mpa)最小弯曲半径(mm)参考重量kg/m内压-层数-压力minmaxminmaxminmaxMpaPsiMpaPsiMpaPsi5-2-374.55.410.611.715.116.737.0536174.010723148.021445900.376.3-2-356.16.912.113.316.718.335.0507270.010143140.0202861000.428-2-327.78.513.714.918.319.832.0463664.09273128.0185461150.5110-2-289.310.116.117.320.622.228.0406756.08114112.0162291300.6012.5-2-2512.313.519.020.623.825.425.0362250.07245100.0144901800.7416-2-2015.416.722.223.827.028.620.0289840.0579680.0115922050.8619-2-1618.619.826.227.831.032.516.0231832.0463664.092742401.0422-2-1421.823.029.431.034.135.714.0202928.0405756.081142801.3525-2-1425.026.434.135.738.540.914.0202928.0405756.075353001.4231.5-2-1131.333.043.345.649.252.411.0159422.0318844.063764202.2338-2-937.739.349.652.055.658.79.0130418.0260836.053165002.7451-2-850.452.062.364.768.371.48.0115916.0231832.046376303.50产品名称：金属软管 为了方便查阅选用方便我们按结构型式不同把金属软管分为：
1、通用螺纹连接式。
2、通用法兰连接式。
3、两端接管连接式。
4、快速接头连接式。
5、几种典型行业的结构形式。注意：在选用所需金属管总成时，一般应首先弄清以下四大要素：
1、尺寸：即软管的通径和长度，确定长度时注意软管弯曲半径，一般静态弯曲半径R j=(5-8)DN，动态弯曲半径R d=10DN。
2、压力：选用承压能力合适的软管，并把工作压力注明。注意：温度对软管承压能力的影响。
3、介质：据介质的腐蚀性选择管体及接头材质。
4、安装：据安装条件选择方便的软管接头，并注意：配置时使软管运动方向合理，不扭曲。