【YD焊条取芯钻头、打桩钻头、螺旋钻头专用焊条价格优惠】价格_厂家

YD焊条取芯钻头、打桩钻头、螺旋钻头专用焊条价格优惠

不限

￥0.00

中国天津

产品属性

图文详情

品牌推荐

品牌

海焊

型号

YD焊条取芯钻头、打桩钻头、螺旋钻头专用焊条

牌号

合金焊条

类型

堆焊焊条

材质

铸铁

酸碱性

酸性焊条

性能

超低氢焊条

加工定制

是

焊条直径

3-5mm

焊芯直径

3-5-6.5-8-9.5（mm）mm

长度

YD焊条取芯钻头、打桩钻头、螺旋钻头专用焊条（mm）mm

工作温度

YD焊条取芯钻头、打桩钻头、螺旋钻头专用焊条（℃）

适用范围

YD焊条取芯钻头、打桩钻头、螺旋钻头专用焊条

YD型【硬质合金堆焊焊条】简介：

      YD型硬质合金复合材料堆焊焊条(简称YD型焊条)，是由粒状烧结硬质合金与有弹性的胎体合金混合制成。外涂一层特殊熔剂并着色，以标识颗粒等级大小。烧结硬质合金颗粒主要为含钴碳化钨，其硬度为HRA89-91;胎体金属为“镍铜”合金，抗拉强度690MPa，硬度：HB≥ 160。
      YD型焊条需要与一种打底焊条(YD—D)和专用熔剂(YD—R)配合使用。均有我厂按比例配套供应。
      YD-D打底焊条是一种外皮涂有特殊熔剂的气焊焊条，用量应为YD焊条重量的15％。

      YD-R是一种复合物制造的熔剂，用量应为YD焊条重量的2％。

      用途：YD型焊条主要用于堆焊石油、矿山、采煤、地质、建筑等工业中一些严重磨损或兼有切削的工件。如：铣鞋、磨鞋、扶正器、扩孔器、钻杆接头、水力割刀、刮刀片、刨煤机刨刀、取芯钻头、打桩钻头、螺旋钻头等。

      堆焊工艺：YD型焊条是采用氧—乙炔火焰进行堆焊，使用的气焊焊咀应比普通气焊碳钢所用的焊咀大。火焰应调成中性或稍偏碳化焰。中性焰焰心的尖端位置应严格控制，不能接触到硬质合金颗粒和工件表面，以免过烧，也就是比普通气焊时焊咀提的要高，这一点是影响堆焊层耐磨寿命的关键，切勿忽视。

      堆焊时应尽量采用平焊位置，其它位置堆焊时应采用适当的胎具。

      工作场地必须通风良好，以免有害健康。

      规格：YD型焊条根据硬质合金颗粒大小，分为：以下八个等级供货：

牌号	公称尺寸(mm)	颗粒等级尺寸(mm)	颜色	备注
YD-9.5	9.5	9.5-6.5	深绿
YD-8	8	8-6.5	深兰
YD-6.5	6.5	6.5-5	红
YD-5	5	5-3	黄
YD-3	3	3-2	粉红
YD-10目	10目	10-18目	浅绿
YD-18目	18目	18-30目	浅兰
YD-30目	30目	30-50目	浅黄

YD型硬质合金堆焊焊条的堆焊工艺

该焊条采用氧乙炔堆焊。操作工艺如下：
(1)清理工件，使被焊工件表面露出金属光泽。
(2)取平焊位置进行堆焊，为此可使用适当的胎具为控制堆焊层厚度，可利用限厚块。
(3)用中性焰预热，焰心勿接触工件表面，距离以25mm为宜。
(4)当工件加热到适当温度时，即可在待堆焊表面涂一层专用焊剂，如熔剂预热得合适，熔剂就会起泡沸腾，此时工件表面的氧化物将被熔剂清除，再继续加热至溶剂布满被堆焊的表面并呈透明液体状态时，表明可开始堆焊打底焊层。
(5)堆焊打底焊层，采用中性焰，用打底焊条尖端不断搅动熔剂，并随之熔化，焊咀不断运行，其运行速度恰好与打底焊条的焊速度相等．要确保熔剂保持在工件表面上。当打底过程结束时，堆焊表面应形成一薄层平滑的打底合金，其厚度约lmm左右为宜。如预热温度不足时，熔融的打底层金属不能流平，并在工件表砸上形成小球或凸起。
(6)堆焊硬质合金焊层。在打底合金层上面，用YD型焊条堆焊，使用中性焰(可稍偏碳化焰)焊咀均匀平稳的在工件表面上移动，火焰对着合金焊条加热(注意不可使焰心尖端接触合金颗粒)，使焊条中胎体合金熔化，随之硬质合金颗粒也一同落下。在熔化的胎体金属凝固之前，要把颗粒安排好，可用左手拿着的合金焊条拔弄，或另一人手持一根打底焊条或石墨棒作拔棍，在一傍迅速拨弄颗粒，使之排列均匀整齐。堆焊层厚度按设计要求控制。
(7)工件堆焊完后，放在不通风的地方，缓慢冷却，不可急冷，有条件可用石棉毡盖上。
(8)工件冷却到室温后，如果有需要，可把堆焊面磨到要求尺寸和形状。
(9)清理工件，去除所有飞溅，熔渣等。

堆焊操作方法正确，堆焊层质量满意的标志是：待冷却后，堆焊层表面呈发亮的金黄色，堆焊层胎体合金与基体金属结合良好，合金颗粒排列紧密，且均匀、牢固的焊嵌在胎体金属里。

过热或过烧的标志是：冷却后胎体金属发红，合金颗粒露出黑色表面，其后果是合金颗粒的工作性能受损，影响使用寿命。

加热不足的标志是：冷却后，呈无光泽的银灰色，胎体合金与基体金属结合不良，堆焊后的工具运转时整个堆焊层有脱落的危险。

美国泰克罗伊、奥地利伯乐、德国伯乐、赫伯特HOBART、德国蒂森、德国Cor o dur、德国UTP、法国SAF、韩国现代、美国阿克泰克、美国哈里斯HARRIS、美国万能焊条、日本日亚焊条、日本神钢焊条、瑞典伊萨ESAB、瑞典阿维斯塔、瑞士奥利康、意大利TFA、英国曼切特条。
北京重庆上海天津海焊美国牛津
江苏省：扬州、南京、徐州、连云港、宿迁、淮安、盐城、泰州、南通、镇江、常州、无锡、苏州。
辽宁省：沈阳、大连、朝阳、阜新、铁岭、抚顺、本溪、辽阳、鞍山、丹东、营口、盘锦、锦州、葫芦岛。
山东省：济南、骏焊青岛、聊城、德州、东营、淄博、潍坊、烟台、威海、日照、临沂、枣庄、济宁、泰安、莱芜、滨州、菏泽。主要销售特种焊条焊丝，代理斯米克、司太立、天泰、电力、京雷、大西洋、金桥、大桥、等
陕西省：西安、延安、铜川、渭南、咸阳、宝鸡、汉中、骏焊，榆林、商洛、
山西省：太原、大同、朔州、阳泉、长治、晋城、忻州、吕梁、晋中、临汾、运城。
四川省：成都、广元、绵阳、德阳、南充、广安、遂宁、内江、乐山、自贡、泸州、宜宾、攀枝花、巴中、达州、资阳、眉山、雅安。
云南省：昆明、曲靖、玉溪、丽江、昭通、思茅、临沧、保山。
浙江省：杭州、宁波、湖州、嘉兴、舟山、绍兴、衢州、金华、台州、温州、丽水。
安徽：合肥、宿州、淮北、阜阳、蚌埠、淮南、滁州、马鞍山、芜湖、铜陵、安庆、黄山、六安、巢湖、池州、宣城、亳州。
福建省：厦门、福州、南平、三明、莆田、泉州、漳州、龙岩、宁德。
甘肃省：兰州、嘉峪关、金昌、白银、天水、酒泉、庆阳、平凉、定西、陇南。
广东省：广州、深圳、清远、韶关、河源、梅州、潮州、汕头、揭阳、汕尾、惠州、东莞、珠海、中山、江门、佛山、肇庆、云浮、阳江、茂名、湛江
贵州省：贵阳、六盘水、遵义、安顺
黑龙江省：哈尔滨、齐齐哈尔、黑河、大庆、伊春、鹤岗、佳木斯、双鸭山、七台河、鸡西、牡丹江、绥化。
河南省：郑州、开封、洛阳、平顶山、安阳、鹤壁、新乡、焦作、濮阳、许昌、漯河、三门峡、南阳、商丘、周口、驻马店、信阳
湖北省：武汉、十堰、襄樊、荆门、孝感、黄冈、鄂州、黄石、咸宁、荆州、宜昌、
湖南省：长沙、张家界、常德、益阳、岳阳、株洲、湘潭、衡阳、郴州、永州、邵阳、怀化、娄底。
吉林省：长春、吉林市、白城、松原、四平、辽源、通化、白山。
江西省：南昌、九江、景德镇、鹰潭、新余、萍乡、赣州、上饶、抚州、宜春、吉安
青海省：西宁、格尔木、德令哈。
广西：南宁、桂林、柳州、梧州、贵港、玉林、钦州、北海、防城港、崇左、百色、河池、来宾、贺州。
TGX-308L焊丝，R308LT1-5不锈钢药芯焊丝

不锈钢用药芯焊棒

种类 ESAB 牌号技术标准熔敷金属力学性能熔敷金属化学成分（％）
SFA/AWS EN 屈服值 Mpa 抗拉强度 Mpa 延伸率％冲击值 J C Si Mn Cr Ni 其它
手工焊条 OK 61.25 A5.4-9E308-15 EN 1600E 19 9 H B 22 430 600 45 20℃ 70 0.06 0.5 1.7 18.5 9.5 －
OK 61.30 A5.4 E308L-17 EN 1600 E 19 9 L R 12 430 560 45 20℃ 70 0.03 0.8 0.7 19.5 10.0 －
OK 61.35 A5.4 E308L-15 EN1600E 19 9 L B 2 2 460 580 45 +20℃ 100-120℃ 70-196℃ 45 0.03 0.4 1.7 19.5 10.5 －
OK 61.41 A5.4 E308L-17 EN1600 E 19 9 L R 5 3 420 560 45 20℃ 65 0.03 0.7 0.8 19.5 10.0 －
OK 61.50 A5.4-92 E308H-17 EN1600 E 19 9 H R 12 430 600 45 20℃ 60 0.05 0.8 0.8 20.0 10. －
OK 61.80 A5.4-92 E347-17 EN 1600E 19 9 Nb R 12 500 630 40 +20℃ 60-80℃ 40 0.03 0.7 0.6 20.0 10.0 Nb 0.3
OK 61.81 A5.4 E347-16 EN1600 E 19 9 Nb R 3 2 560 700 32 +20℃ 60 0.06 0.6 1.6 20.0 10.0 Nb 0.7
OK 61.85 A5.4 E347-15 EN1600 E 19 9 Nb B 2 2 500 620 40 +20℃ 100-60℃ 70 0.05 0.5 1.7 19.5 10.0 Nb 0.5
OK 61.86 A5.4 E347-17 EN1600 E 19 9 Nb R 1 2 520 660 35 +20℃ 55 0.03 0.7 0.8 19.0 10.0 Nb 0.3
OK 63.20 A5.4 E316L-16 EN1600 E 19 12 3 L R 1 1 480 580 35 +20℃ 65-60℃ 45-120℃ 32 0.03 0.7 0.8 18.5 12.0 Mo2.8
OK 63.30 A5.4 E316L-17 EN1600 E 19 12 3 L R 1 2 460 570 40 +20℃ 60-125℃ 32 0.03 0.8 0.6 18.0 12.0 Mo2.8
OK 63.31 A5.4 E316L-17 EN1600 E 19 12 3 L R 3 2 460 570 38 +20℃ 60-125℃ 35 0.03 0.8 0.7 19.0 11.0 Mo2.8
OK 63.34 A5.4 E316L-16 EN1600 E 19 12 3 L R 11 440 600 40 +20℃ 65 0.03 0.8 0.8 18.5 12.0 Mo2.8
OK 63.35 A5.4 E316L-15 EN1600E 19 12 3 L B 2 2 460 600 35 +20℃ 95-120℃ 60-196℃ 35 0.03 0.5 1.7 18.5 12.6 Mo2.8
OK 63.41 A5.4 E316L-17 EN1600 E 19 12 3 L R 5 3 430 570 45 +20℃ 60 0.03 0.8 0.7 18.0 12.0 Mo2.8
OK 63.80 A5.4 E318-17 EN 1600E 19 12 3 Nb R 3 2 500 620 35 +20℃ 55 0.02 0.8 0.6 18.0 12.0 Mo2.8Nb0.3
OK 64.30 A5.4 E317L-17 EN1600 E 19 13 4 LR 3 2 480 600 30 +20℃ 45 0.03 0.7 0.7 19.0 13.0 Mo2.8
OK 67.13 A5.4 E310-16 EN 1600 E 25 20 R 12 560 600 35 +20℃ 60 0.1 0.5 1.9 26.0 21.0 －
OK 67.15 A5.4 E310-15 EN 1600 E 25 20 B 22 410 590 35 +20℃ 100 0.1 0.3 2.0 26.0 20.0 －
OK 67.20 A5.4 E309MoL-16 EN1600 E 23 12 2 LR 1 1 480 640 35 +20℃ 60 0.03 0.8 0.8 23.0 13.0 Mo2.9
OK 67.50 A5.4 E2209-17 EN 1600E 22 9 3 N L R 3 2 660 820 25 +20℃ 70 0.03 0.8 1.0 23.0 9.0 Mo3.0N0.15
OK 67.55 A5.4 E2209-15 EN 1600E 22 9 3 N L B 2 2 650 800 28 +20℃ 100-40℃ 75-60℃ 65 0.03 0.7 1.0 23.0 9.0 Mo3.0N0.15
OK 67.60 A5.4 E309L-17 EN 1600E 23 12 L R 3 2 470 580 32 +20℃ 50-10℃ 40 0.03 0.8 0.9 24.0 12.5 －
OK 67.62 A5.4 E309-26 EN1600 E 23 12 R 7 3 450 570 40 +20℃ 60 0.05 0.8 0.6 24.0 12.5 －
OK 67.66 A5.4 E309L-16 EN1600 E 23 23 L R 3 2 430 580 45 +20℃ 70 0.03 0.4 1.0 23.0 13.0 －
OK 67.70 A5.4 E309MoL-17 EN1600 E 23 12 2 LR 3 2 510 620 33 +20℃ 50 0.03 0.8 0.6 23.0 13.0 Mo2.7
OK 67.75 A5.4 E309L-15 EN1600 E 23 12 L B 4 2 460 570 35 +20℃ 75-80℃ 55 0.03 0.3 0.2 24.0 13.0 Mo0.3
OK 68.15 A5.4 E410-15 EN1600 E 13 B 4 2 390 520 25 +20℃ 55 0.06 0.5 0.5 13.0 －－
OK 68.17 A5.4 E410NiMo-16 EN 1600E 13 4 R 3 2 650 870 17 +20℃ 45-10℃ 45-40℃ 40 0.03 0.4 0.6 12.0 4.6 Mo0.6
OK 68.25 A5.4E410NiMo-15 EN 1600E 13 4 B 4 2 680 880 17 +20℃ 60-20℃ 53 0.03 0.4 0.6 12.5 4.5 Mo0.6
OK 68.60 EN 1600 E 25 4 R 3 2 660 800 15 +20℃ 30 0.05 1.1 1.2 26 5 Mo1.5N0.18
OK 68.81 A5.4 E312-17 EN1600 E 29 9 R 3 2 580 750 25 +20℃ 30 0.12 0.7 0.8 29.0 10.0 －
OK 69.25 EN 1600E 20 16 3 Mn L B 4 2 450 650 30 +20℃ 90-196℃ 50 0.03 0.5 6.5 19.0 16.0 Mo3.0N0.15
OK 69.33 A5.4E385-16 EN 1600E 20 25 5 Cu N L R 3 2 400 575 35 +20℃ 80-140℃ 45 0.03 0.5 1.0 20.5 25.0 Mo5.0Cu1.5
OK61.20 E308L-16焊条    钛酸性焊条，用于焊接19Cr10Ni型，不锈钢和类似成份的钢种，特别适合焊接薄壁管，1.6-2.5mm的焊条能够用于包括立向下焊在内的全位置焊接
OK61.25 E308L-15焊条    碱性焊条，焊缝含碳量较高，用于石化企业的高温设备
OK61.30 E308L-17焊条     钛酸性焊条，交直流两用，引弧和再引弧容易，焊缝成形好，熔渣自动分离，用于焊接19Cr10Ni型钢及含有稳定化元素的成分类似钢种
OK61.35 E308L-15焊条      碱性焊条，立焊和仰焊性能好，焊缝在超低温下（-196℃）韧性好，用于焊接液化天然气结构
OK61.41 E308L-26焊条       钛酸型超低碳钢高效焊条，适合平焊和平角焊，用于焊接19Cr10Ni型钢及含有稳定化元素的成分类似钢种
OK61.50 E308H-17焊条        钛酸型焊条，用于焊接高温下适用的18Cr10Ni型非稳定化奥氏体钢
OK61.80 E347-17焊条        钛酸性含Nb不锈钢焊条，碳含量低用于焊接321和347钢在400℃以下具有抗晶间腐蚀性能
OK61.81 E347-16焊条        钛型含Nb不锈钢焊条，用于焊接TiNb的18Cr8Ni不锈钢，特别适合高温场合
OK61.85 E347-15焊条        含Nb碱性焊条，特别适合焊接含NbTi的不锈钢，立焊和仰焊性能好，适合管道焊接
OK61.86 E347-17焊条        钛酸性焊条，用于焊接含Nb、Ti的19Cr10Ni型不锈钢，铁素体量较低
OK62.53焊条                钛型焊条，用于高温场合，焊接抗氧化温度约1150℃，推荐用于焊接Avesta253MA\UNS S30815等钢种
OK62.73焊条               酸性焊条熔敷金属为奥氏体+铁素体型，抗裂性好，适合焊接裂纹敏感性高的材料，也用于焊接5Cr-0.5Mo钢焊后不用热处理
OK62.75焊条                钛碱性焊条，熔敷金属为奥氏体+铁素体型，抗裂性好，适合焊接裂纹敏感性高的材料，装甲钢以及异种钢焊接、也用于焊接5Cr-0.5Mo钢，焊后不用热处理，在硬面堆焊中，用于焊接吸收应立的过渡层
OK63.20 E316L-16焊条       钛酸型焊条，用于焊接316L、18Cr12Ni3Mo型不锈钢，特别适合全位置焊接薄壁管、引弧和再引弧很容易
OK63.30 E316L-17焊条         钛酸性焊条，引弧和再引弧容易，焊缝成形好，渣自动分离，用于焊接18Cr12Ni3Mo型钢及含有稳定化元素的成分类似钢种
OK63.32 E308Mo-26焊条     钛型高效焊条，用于不锈钢，奥氏体锰钢与碳钢、低合金钢之间的异种钢焊接、也用于焊接装甲钢和不锈钢堆焊层
OK63.34 E316L-16焊条       钛酸性焊条，19Cr12Ni3Mo型，用于立向下焊接成分类似不锈钢，焊缝成形好，焊角过渡平滑、渣量少，脱渣好
OK63.41 E316L-26焊条       钛酸性高效焊条，18Cr12Ni-3Mo型，适合平焊、焊缝表面光滑、角焊缝轻微凹陷
OK63.35 E316L-15焊条      碱性焊条，立焊和仰焊性能好，抗裂性好，抗气孔能力强，用于焊接18Cr12Ni3Mo型钢，焊缝在超低温下（-196℃）韧性好，也适合焊接液化天然气结构
OK63.80 E318-17焊条        钛酸性焊条，用于焊接含Nb或Ti的18Cr12Ni23Mo型不锈钢
OK63.85 E318-15焊条       碱性焊条，焊缝含Nb，用于焊接成分类似的钢种
OK64.30 E317-17焊条        钛酸性焊条，交直流两用，全位置焊接，焊缝表面光滑，Mo含量高，抗酸腐蚀和抗点蚀性能优于316L，用于焊接19Cr13Ni3.5Mo型奥氏体不锈钢
OK64.63焊条                  钛碱性焊条，熔敷金属为纯奥氏体组织、抗腐蚀性能很好，除立向下外的全位置焊接性能优越
OK67.13 E310-16焊条          钛碱性焊条，纯奥氏体焊缝，抗氧化温度为1100-1150℃，用于焊接25Cr20Ni型奥氏体不锈钢，也用于装甲钢等空冷淬硬钢和不锈钢于碳钢之间的异种钢焊接
OK67.15 E310-15焊条          碱性焊条，抗裂性好，用于焊接25Cr20Ni型不锈钢、装甲钢、奥氏体锰钢和异种钢
OK67.20焊条                   钛酸性不锈钢焊条，用于不锈钢于碳钢和低合金钢之间的异种钢焊接，包括立向下在内的全位置焊性能良好
OK67.43 E307-16焊条            钛碱性焊条，交直流两用，熔敷金属含有少量均匀分布的铁素体，抗裂性能很好，适合焊接13Mn钢和这类钢于其他钢之间的异种钢焊接
OK67.45 E307-15焊条              碱性焊条，铁素体含量低于5%，抗裂型能好，适合焊接12-14%Mn钢和这种钢于其他钢之间的异种钢焊接，也适合硬面堆焊前的过渡层焊接
OK67.50 E2209-17焊条            钛酸型焊条，在300℃高温下具有良好的抗应力腐蚀性能，用于焊接铁素体-奥氏体双相不锈钢
OK67.51 E2209-26焊条           钛酸性高效不锈钢焊条，用于焊接双相不锈钢，如UNS S31803,也用于双相钢与CMn钢之间的异种钢焊接

种类焊剂牌号密度Kg/dm3 碱性度配用焊丝牌号熔敷金属力学性能熔敷金属化学成分（％）
     屈服值Mpa 抗拉强度Mpa 冲击值J C Si Mn Cr Ni Mo
埋弧焊剂 OK Flux 10.16 ≈1.2 2.4 OK Autrod 19.81 490 730 +20℃ 80-60℃   75-196℃ 60 0.02 0.2 0.7 18.0 Bal. 16.0
    OK Autrod 19.82 425 700 -140℃ 100-196℃ 80 0.01Fe2.0 0.3Nb3.5 0.3 21.0 Bal. 9.0
    OK Autrod 19.85 360 600 +20℃ 140-196℃ 100 0.01Fe1.0 0.3 Nb2.3 3.2 19.0 Bal. 2.0
OK Flux 10.92 ≈1.0 1.0 OK Autrod 16.10 365 580 -60℃ 60 0.02 0.9 1.0 20.0 10.0 －
    OK Autrod 16.15 365 580 -60℃ 60 0.03 0.9 1.0 20.0 10.0 0.75
    OK Autrod 16.21 470 640 -60℃ 55-110℃ 40 0.04 0.8 0.9 20.0 10.0 Nb0.5

不锈钢用焊条

Z308铸铁焊条

符合 GB EZNi-1
相当 AWS ENi-C1

说明:Z308是纯镍焊芯、强还原性石墨型药皮的铸铁焊条，施焊时，焊件可不预热，具有良好的抗裂性能和加工性能。镍价格昂贵，应该在其它焊条不能满足时才可选用。交直流两用。

用途:用于铸铁薄件及加工面的补焊，如发动机座、机床导轨、齿轮座等重要灰口铸铁件。

熔敷金属化学成分(%)

化学成分	C	Mn	Si	S	Ni	Fe	其它元素总量
保证值	≤2.00	≤1.00	≤2.50	≤0.030	≥90	≤8	≤1.00

参考电流(AC、DC+)

焊条直径(mm)	φ2.5	φ3.2	φ4.0	φ5.0
焊接电流(A)	50~100	70~120	110~180	160~190

注意事项:
1.焊前焊条须经150℃左右烘焙1h。
2.可以通过锤击焊缝消除焊补区应力，避免裂纹。

上海斯米克焊条

【上海斯米克电焊条】简介

Category
类别
Trade-
Mark
牌号
Equivalent to China Standard
相当国标
Characteristics & application
特性和用途
Equivalent to AWS
相当AWS

Hard-surfacing
硬
面

堆

焊

D 667
EDZCr-B-15
HRc≥48. Resistance to wear, gas corrosion and oxidation. Hardfacing of blast furnace hopper and cracker part.
HRc≥48，耐磨、耐气蚀、抗氧化。堆焊高炉料钟、破碎机件
　
D 802
EDCoCr-A-03
HRc38-47. Resistance to heat, wear and corrosion. Hardfacing of high temperature part such as the edge of thermo-cutter.
HRc38-47，耐热、耐蚀、耐磨。堆焊高温工件如热剪切刀刃
ECoCr-A
D 812
EDCoCr-B-03
HRc45-50. Resistance to heat, wear and corrosion. Hardfacing of high temperature part such as internal-combustion engine valve.
HRc45-50，耐热、耐蚀、耐磨。堆焊高温工件如内燃机阀
ECoCr-B
D 822
　
HRc≥53. Resistance to Wear and heat, bad shock resistance. Hardfacing of rotating blade wheel of boiler.
HRc≥53，耐热、耐磨，但抗冲击性差。堆焊锅炉旋转叶轮
　
D 832
EDCoCr-C-03
HRc≥50. Wear and heat resistance. Hardfacing of high temperature part such as hot-rolling guided way.
HRc≥50，耐热、耐磨。堆焊高温工件如热轧导轨
ECoCr-C
D 842
EDCoCr-D-03
HRc28-38. Corrosion and thermo-fatigue resistance, work harding. Hardfacing of hot forging die.
HRc28-38，耐蚀、抗热疲劳，具有加工硬化性。堆焊热锻模
　

Cast iron

铸

铁
Z 308
EZNi
Pure nickel, excellent general properties. Used to weld thin cast iron part and repair welding machined surface, such as guided way of machine tool.
纯镍，综合性能好。铸铁薄件及加工面补焊用，如机床导卫
ENi-Cl
Z 408
EZNiFe
Iron nickel, high strength and excellent ductility. Repair welding of important gray cast iron and nodular cast iron, such as cylinder cap.
镍铁，强度高、塑性好。重要灰铸铁及球铁焊补用，如汽缸盖
ENiFe-Cl
Z 508
EZNiCu-1
Copper nickel, good machinability and bad crack resistance. Repair welding of sand hole and gray cast iron machined surface subject to no load.
镍铜，易加工，但抗裂性较差。不受力的灰铸铁加工面及砂眼补焊
ENiCu-B

Copper alloys

铜

合

金
Cu 107
ECu
Red copper, atmosphere and sea water corrosion and excellent electric conductivity. Welding of red copper such as electrical copper row.
紫铜，耐大气，海水腐蚀，导电性好。紫铜焊接用，如导电铜排
ECu
Cu 207
ECuSi
Silicon bronze, corrosion resistance and high strength. Welding of copper, silicon bronze and brass.
硅青铜，耐蚀、强度高。铜、硅青铜及黄铜焊接用
ECuSi
Cu 227
ECuSnB
Tin phosphor bronze, corrosion resistance and high strength. Welding of copper, silicon bronze and brass.
锡磷青铜，耐蚀、强度高。铜、硅青铜及黄铜焊接用
ECuSn-C
Cu 237
ECuAl
Aluminum bronze, wear and corrosion and high strength. Welding or surfacing of copper alloys.
铝青铜，耐磨、耐蚀，强度高。铜合金焊接或堆焊用
ECuAl-A2

Aluminum alloys

铝
合
金
Al 109
TAl
Pure aluminum, excellent corrosion resistance and middle strength. Welding of pure aluminum.
纯铝，耐蚀性好，但强度不高，纯铝焊接用
E1100
Al 209
TAlSi
Silicon aluminum, good crack resistance and wide range of usage. Welding of aluminum alloys other than aluminum magnesium alloys.
铝硅，抗裂性好，通用性大。铝合金焊接用，不宜焊接铝镁合金
E4043
Al 309
TAMn
Manganese aluminum, corrosion resistance and high strength. Welding of aluminum alloys.
铝锰，强度高，耐蚀。铝合金焊接用
E3003

Nickel alloys
镍合金
Ni 102
ENi-1
Pure nickel. Welding and surfacing of nickel and nickel to steel.
纯镍，用于镍、镍与钢的焊接与堆焊
ENi-1
Ni 207
ENiCu-7
Copper nickel. Welding and surfacing of copper nickel and copper nickel to steel.
镍铜，用于镍铜、镍铜与钢的焊接与堆焊
ENiCu-7
Category
类别
Trade
mark
牌号
Chemical composition
主要成份(%)
Characteristics & application
特性和用途
Equivalent to AWS
相当AWS

Hardfacing

硬

面

堆

焊
S 101
C3 Cr28 Ni4
Si3.5 Fe Rem.
HRc48-54. Resistance to wear, gas corrosion and oxidation. Hardfacing of bucket tooth and case pump.
HRc48-54，耐磨、耐气蚀、抗氧化。堆焊铲斗齿，泵套
　
S 111
C1 Cr29 W5
Co Rem.
HRc38-47. Resistance to wear and corrosion at high-temperature. Hardfacing of high temperature and pressure valve.
HRc38-47，高温下耐磨、耐蚀。堆焊高温高压阀门
ECoCr-A
S 112
C1.5 Cr29 W8
Co Rem.
HRc45-50. Resistance to wear and corrosion at high-temperature. Hardfacing of valve and hot-rolling pass.
HRc45-50，高温下耐磨、耐蚀。堆焊阀门，热轧孔型
ECoCr-B
S 113
C2.5 Cr30 W17
Co Rem.
HRc≥55. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of screw charging carriage.
HRc≥55，高温下耐磨、耐热，但抗冲击性差。堆焊螺旋送料机用
　
S 114
C2.5 Cr30 W12
Co Rem.
HRc≥53. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of three-cone bit.
HRc≥53，高温下耐磨、耐热，但抗冲击较差。堆焊牙轮钻头
ECoCr-C

Copper
alloys

铜

合

金
S 201
Sn1 Si0.3Mn0.3
Cu Rem.
Good mechanical properties and crack resistance. Gas welding and argon arc welding of red copper.
机械性能好，抗裂性好。紫铜气焊及氩弧焊用
ERCu
S 211
Si3 Mn1
Cu Rem.
Good mechanical properties. Argon arc welding of copper alloys and MIG brazing of steel.
机械性能好，铜合金氩弧焊及钢的MIG钎焊用
ERCuSi-Al
S 212
Sn5 Cu Rem.
Wear resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨性好。铜合金氩弧焊及钢的堆焊用
ERCuSn-A
S 213
Sn8 Cu Rem.
Wear resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨性好。铜合金氩弧焊及钢的堆焊用
ERCuSn-C
S 214
Al7.5 Cu Rem.
Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用
ERCuAl-A1
S 215
Al9 Cu Rem.
Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel.
耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用
ERCuAl-A2
S 221
Cu60 Sn1 Si0.3
Zn Rem.
Melting point is about 890℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约890℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
　
S 221F
Cu60 Sn1 Si 0.3
Zn Rem.
S221 welding rod coated with flux.
外涂焊剂的S221焊丝
　
S 222
Cu58Sn0.9Si0.1
Fe0.8 Zn Rem.
Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约880℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
RBCuZn-C
S 222F
Cu58Sn0.9Si0.1
Fe0.8 Zn Rem.
S222 welding rod coated with flux.
外涂焊剂的S222焊丝
RBCuZn-C
S 223
Cu59 Sn0.6
Zn Rem.
Melting point is about 900℃. Braze welding of copper, steel and cast iron.
熔点约900℃。铜、钢、铸铁钎焊用
RBCuZn-A
S 224
Cu62 Si0.5
Zn Rem.
Melting point is about 905℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点约905℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
　
Copper
alloys
铜

合

金
S 225
Cu48 Ni10
Zn Rem.
Melting point is about 935℃ and high strength. Braze welding of steel, nickel and carbide alloys.
熔点约935℃。高强度,钎焊钢、镍及硬质合金用
RBCuZn-D
S 225F
Cu48 Ni10
Zn Rem.
S225 welding rod coated with flux.
外涂焊剂的S225焊丝
RBCuZn-D
S 226
Cu60 Sn0.3
Si0.2 Zn Rem.
Melting point is about 900℃. Gas welding of brass, also braze welding of copper, steel and cast iron.
熔点约900℃。黄铜气焊用，也可钎焊铜、钢、铸铁
　
S 227
Cu58Sn0.9Ni0.5
Si0.1 Fe0.8
Zn Rem.
Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron.
熔点880℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
RBCuZn-B
S 229
Cu55 Ni6 Mn4
Zn余
Melting point is about 920℃, high strength. Braze welding of steel, nickel and hard carbide.
熔点约920℃。高强度,钎焊钢、镍及硬质合金用
　
Aluminum alloys

铝

合

金
S 301
Al≥99.5
Good ductility and corrosion resistance. Gas welding and argon arc welding of pure aluminum.
塑性好、耐蚀。纯铝气焊、氩弧焊用
ER1100
S 311
Si5 Al Rem.
Corrosion resistance, wide range of usage. Gas welding and argon arc welding of aluminum alloys other than high magnesium alloys.
抗裂性好，通用性大。铝合金气焊、氩弧焊用。不宜用高镁合金
ER4043
S 321
Mn1.3 Al Rem.
Good corrosion resistance, weldability and ductility. Gas welding and argon arc welding of aluminum alloys.
良好的耐蚀性、可焊性及塑性。铝合金气焊、氩弧焊用
　
S 331
Mg5 Mn0.4
Al Rem.
Corrosion resistance and high strength. Argon arc welding of aluminum alloys.
耐蚀，强度高。铝合金氩弧焊用
ER5183
斯米克钎焊料分别有：（铜锌钎焊料），（铜磷银基钎焊料），（铝基钎焊料），（锡铅钎焊料），（镍基钎焊料).简介如下：
Category
类别
Trade-mark
牌号
Specification
规格
Melting
Point
熔点(℃)
Chemical
composition
主要成份(%)
Application
用途

Equivalent
to AWS
相当AWS

Copper
zinc
铜锌
L103
Wire & rod
丝
885-888
Cu54 Zn Rem.
Brazing of copper, bronze and steel, subjected to low load.
钎焊铜、青铜和钢等受力不大工件
　
L104
Foil
箔
890-930
Cu57 Mn2
Co2 Zn Rem.
Brazing of carbide cutting tool.
钎焊硬质合金刀具
　

Copper
phosphorus

铜磷
L201
Cast rod, wire & rod, powder
铸条、丝、粉
710-800
P7 Cu Rem.
Brazing of copper and copper alloys.
钎焊铜及铜合金
BCuP-2
L204
Cast rod, wire
铸条、丝
640-815
P5 Ag15
Cu Rem.
Brazing of copper, copper alloys, silver and molybdenum etc.
钎焊铜及铜合金、银、钼等金属。
BCuP-5
L205
Cast rod, wire & rod, powder
铸条、丝、箔
640-800
P6 Ag5
Cu Rem.
Brazing of copper and copper alloys.
钎焊铜及铜合金
BCuP-3
L207
Cast rod, wire & rod
铸条、丝
640-770
P7 Ag5
Cu Rem.
Brazing of copper and copper alloys.
钎焊铜及铜合金
BCuP-7
L209
Cast rod, wire
铸条、丝
684-710
P7 Ag2
Cu Rem.
Brazing of copper and copper alloys.
钎焊铜及铜合金。
BCuP-6

　Silver
base

银基
L302
Wire & rod
丝
745-775
Ag25 Cu40
Zn Rem.
Brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
　
L303
Wire & rod
丝
660-725
Ag45 Cu30
Zn余
Brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
BAg-5
L303F
Flux coated rod
涂药丝
660-725
Ag45 Cu30
Zn Rem.
L303 coated with flux, the same application as L303.
外涂钎剂的L303，用途与L303相同
BAg-5
L304
Foil
箔
690-775
Ag50 Cu34
Zn Rem.
Brazing of copper, copper alloys and steel etc.
钎焊铜及铜合金、钢等
BAg-6
L308
Wire & rod
丝
779-780
Ag72 Cu Rem.
Brazing of copper and nickel under vacuum or reducing protective atmosphere.
铜和镍的真空或还原保护气氛钎焊
BAg-8
L312
Wire & rod
丝
595-605
Ag40.Cu.Zn.Cd
Brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
　
L313
Wire & rod
丝
625-635
Ag50.Cu.Zn.Cd
Brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
BAg-1a
L321
Wire & rod
丝
615-650
Ag56.Cu.Zn.Sn
Brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
BAg-7
L323
Wire & rod
丝
665-755
Ag30.Cu.Zn.Sn
Brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
　
L325
Wire & rod
丝
645-685
Ag45.Cu.Zn.Sn
Brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
BAg-36
L326
Wire & rod
丝
650-720
Ag38.Cu.Zn.Sn
Brazing of copper, copper alloys, steel and stainless steel etc.
钎焊铜及铜合金、钢及不锈钢等
BAg-34

Aluminum base
铝基
L400
Cast rod, wire & rod
铸条、丝
577-582
Si11.5
Al Rem.
Brazing of aluminum and aluminum alloys.
铝及铝合金的钎焊
BAlSi-4
L401
Cast rod
铸条
525-535
Si5 Cu28
Al Rem.
Brazing of aluminum and aluminum alloys.
铝及铝合金的钎焊
　

Tin lead
锡铅
L600
Wire & rod
丝
183-185
Sn60 Sb≤0.8
Pb Rem.
Soldering of fusible metals and heat-treated part.
易熔金属及热处理件的钎焊
60Sn
L601
Wire & rod
丝
183-227
Sn18 Sb2
Pb Rem.
Soldering of copper, copper alloys and galvanized iron plain sheet.
铜及铜合金、镀锌铁皮的钎焊。
18Sn
L602
Wire & rod
丝
183-256
Sn30 Sb2
Pb Rem.
Soldering of copper, brass, copper alloys and galvanized iron plain sheet.
铜、黄铜、铁、镀锌铁皮的钎焊
30Sn
L603
Wire & rod
丝
183-235
Sn40 Sb2
Pb Rem.
Soldering of copper, copper alloys, steel and zinc parts.
铜及铜合金、钢、锌制零件的钎焊
40Sn
L604
Wire & rod
丝
183-222
Sn90 Sb≤0.15
Pb Rem.
Soldering of copper and steel for food and medicine field.
食品、医疗所需铜、钢等金属的钎焊
90Sn
L605
Wire & rod
丝
232-240
Ag5 Sn95
Soldering of copper and steel for electrical and food field.
电器、食品所需铜、钢等金属的钎焊
　
L608
Wire & rod
丝
295-305
Sn5.5 Ag2.5
Pb Rem.
Soldering of copper, copper alloys, steel and stainless steel.
铜及铜合金、钢及不锈钢的钎焊
　
Nickel base
镍基
L702
Powder
粉
970-1000
Cr7 B3 Si4
Ni Rem.
Brazing of stainless steel under vacuum or protective atmosphere.
不锈钢真空或保护气氛钎焊
BNi-2
Category
类别
Trade-mark
牌号
Product name
名称
Characteristics & application
特性和用途
Gas
welding
气焊
CJ301
Copper gas welding flux
铜气焊熔剂
Melting point is about 650℃, flux for gas welding and brazing of copper and copper alloys.
熔点约650℃，铜及铜合金气焊或钎焊的助熔剂
CJ401
Aluminum gas welding flux
铝气焊熔剂
Melting point is about 560℃, flux for gas welding of aluminum and aluminum alloys.
熔点约560℃，铝及铝合金气焊的助熔剂

Silver
brazing
银钎焊
QJ101
Silver brazing flux
银钎焊熔剂
Brazing flux of copper, copper alloys, steel and stainless steel within 550-750℃.
在550-750℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
QJ102
Silver brazing flux
银钎焊熔剂
Brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃.
在600-850℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
QJ102A
Silver brazing flux
银钎焊熔剂
Brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃. Non agglomeration.
在600-850℃范围钎焊铜及铜合金、钢及不锈钢。不易结块
QJ112
Silver brazing paste flux
膏状银钎焊熔剂
Brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃.
在600-850℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
QJ103
Silver brazing flux
银钎焊熔剂
Brazing flux of copper, copper alloys, steel and stainless steel within 550-750℃.
在550-750℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
Aluminum brazing
铝钎焊
QJ201
Aluminum brazing flux
铝钎焊熔剂
Brazing flux of aluminum and aluminum alloys within 450-620℃.
在450-620℃范围钎焊铝及铝合金的助熔剂
QJ207
Aluminum brazing flux
铝钎焊熔剂
Brazing flux of aluminum and aluminum alloys within 560-620℃.
在560-620℃范围钎焊铝及铝合金的助熔剂
Category
类别
Trade-
mark
牌号
Chemical
composition
化学成份(%)
Hardness
硬度
Application
用途

　Oxy-
Acetylene
Flame
spray-
using
氧

乙

炔

焰

喷

焊
F103
Cr10 B1.5 Si3 Ni Rem.
HRc 25
Spray-fusing of cast iron parts,, such as die for glass, cylinder, and guide.
铸铁件的喷焊，如玻璃模具，汽缸、导轨
F101
Cr10 B2.5 Si3 Ni Rem.
HRc 45
Spray-fusing of parts resistance to wear and corrosion, such as valve, the rotator and piston of pump.
耐磨、耐蚀件的喷焊，如阀门、泵转子、泵柱塞
F101Fe
Cr10 B2.5 Si3 Fe10
Ni Rem.
HRc 45
Spray-fusing of corrosion-resistant parts, such as axle and stigma.
耐磨件的喷焊，如轴类、汽门
F102
Cr16 B4 Si4 Ni Rem.
HRc 60
Spray-fusing of parts resistance to wear, corrosion and high temperature oxidation, such as die and piston.
耐磨、耐蚀、抗高温氧化工件的喷焊，如模具、柱塞
F102Fe
Cr16 B4 Si4 Fe15
Ni Rem.
HRc 60
Spray-fusing of corrosion-resistant parts, such as axle and cold die.
耐磨件的喷焊，如轴类、冷模具
F105
F102+50%WC
HRc 60
Spray-fusing of parts resistance to grain-wear , such as guide plate, scraper and blade of fan.
抗磨粒磨损场合的喷焊，如导板、刮板、风机叶片
F105Fe
F102Fe+35%WC
HRc 60
Spray-fusing of parts resistance to grain-wear, such as guide plate, scraper and blade of fan.
抗磨粒磨损场合的喷焊，如导板、刮板、风机叶片
F108
F102+80%WC
HRc 60
Spray-fusing of parts resistance to strong grain-wear and free machining, such as harrow teeth of dredger.
抗强烈磨粒磨损，无需加工场合的喷焊，如挖泥船耙齿
F301
Cr5 B4 Si4 Ni30
Fe Rem.
HRc 45
Spray-fusing of vulnerable parts of agricultural machinery and mining machinery, such as gear and axletree.
农机,矿山机械易损件的喷焊，如齿轮，车轴
Track iron powder
轨铁粉
Cr5 B1.5 Si3 Ni30
Fe Rem.
HRc 28
Repair spray-fusing of defects such as scratch and concavity of railroad track.
铁路钢轨擦伤、低塌等缺陷的修复喷焊

Oxy-acetylene flame spraying

氧
乙
炔
焰
喷
涂
F111
Cr5 B1.5 Si3 Ni30
Fe Rem.
HB 150
Spraying of bearing and cutting parts etc.
轴承、切削件等的喷涂
F113
Cr10 B1.5 Si3 Ni Rem.
HB 250
Spray-fusing or spraying, such as roll, piston and axle of wear and corrosion resistance.
喷涂亦可喷焊，如滚筒、柱塞、耐蚀耐磨轴等
F313
Cr15 B1.5 Fe Rem.
HB 250
Spraying of dryer of papermaking and axle.
造纸烘缸、轴类的喷涂
F314
Cr18 Ni9 B1.5 Fe Rem.
HB 250
Spraying of axle.
轴类喷涂
F412
Sn10 P0.3 Cu Rem.
HB 80
Spraying of axle and bearing.
轴、轴承的喷涂
F512
复合Al5Ni95

Backing spray of transition layer between base and working layer.
喷涂层的基体与工作层之间过渡（打底）层用喷涂

PTA
hardfacing
等
离
子
弧
喷
焊
F221
Cr26 W5 B0.7 Co Rem.
HRc 43
PTA hardfacing of sealing surface of high temperature and high pressure valve and the edge of hot shearing tool.
高温高压阀门密封面、热剪切刃口的等离子喷焊
F223
Cr21 W5 B1.5 Co Rem.
HRc 40
PTA hardfacing of parts resistance to wear and corrosion at high temperature, such as valve under high temperature and high pressure, and blower.
高温下耐磨耐蚀件的喷焊，如高温高压阀门、鼓风机
F321
Cr13 B1.5 Si1 Fe Rem.
HRc 45
PTA hardfacing of corrosion-resistant parts under mid-temperature and mid-pressure, such as stop-plate etc.
中温中压阀门的闸板及其他耐磨件的等离子喷焊
F322
Cr23 Ni13 Si5 B1
Fe Rem.
HRc 40
PTA hardfacing of corrosion-resistant parts under mid-temperature and mid-pressure, such as valve base etc.
中温中压阀门的阀座及其他耐磨件的等离子喷焊
F422
Sn10 P0.3 Cu Rem.
HB 80
PTA hardfacing of axle and bearing etc.
轴、轴承等离子喷焊

类别
品名
AWS型号
熔敷金属化学成分(%)
熔敷金属力学性能
特征与用途
C
Si
Mn
P
S
Ni
Cr
Mo
其它
σ0.2(MPa)
δb(MPa)
δ(%)
Akv(J)
焊条
NC-38
E308-16
0.07
0.35
1.69
0.023
0.002
9.58
20.49

410
600
46
-0℃:74
用于对接焊及角焊，适于焊接SUS304钢
NC-38L
E308L-16
0.034
0.33
1.42
0.022
0.006
9.57
20.07

410
580
48
0℃:78
用于对接焊及角焊，与NC-38相比，NC-38L含碳量较低，适于焊接SUS304L钢
NC-39
E309-16
0.08
0.53
1.50
0.020
0.003
12.72
23.97

410
590
39
0℃:62
用于不锈钢与其它钢的异种钢焊接和复合刚过渡层焊接
NC-39L
E309L-16
0.030
0.60
1.50
0.020
0.005
12.50
23.13

410
560
42
0℃:67
用于不锈钢与其它钢的异种钢焊接和复合钢过层焊接,与NC-39相比，NC-39L的含碳量较低
NC-39MoL
E309MoL-16
0.029
0.51
1.28
0.024
0.005
12.65
23.08
2.29

450
630
41
0℃:65
用于不锈钢与其它钢的异种钢焊接和复合钢过渡层焊接，与NC-39相比，NC-39MoL含碳量较低
NC-36L
E316L-16
0.023
0.57
1.56
0.025
0.003
12.17
18.68
2.20

420
580
45
0℃:83
用于对接焊及角焊，适于焊接SUS316L钢，与NC-36相比，NC-36L含碳量较低
NC-38LT
E308L-16
0.034
0.38
2.12
0.022
0.002
10.89
18.36

370
540
51
-196℃:52
用于焊接深冷温度下使用的18%Cr-8%Ni不锈钢,烘干: 150-200℃×0.5-1h
NC-36LT
E316L-16
0.030
0.52
2.02
0.021
0.003
13.06
17.28
2.25

390
530
44
-196℃:40
用于焊接深冷温度下使用的18%Cr-12%Ni-2%Mo不锈钢,烘干:150-200℃×0.5-1h
NC-317L
E317L-16
0.030
0.50
1.17
0.027
0.004
13.28
19.11
3.50

440
600
39

用于焊接19%Cr-13%Ni-3%Mo超低碳不锈钢,烘干:150-200℃×0.5-1h
NC-37
E347-16
0.060
0.60
1.66
0.018
0.002
9.82
20.22

Nb:0.67
470
670
34

用于焊接18%Cr-8%Ni-Nb不锈钢
CR-40
E410-16
0.08
0.47
0.28
0.020
0.006

12.83

290
510
33

用于焊接13%Cr马氏体不锈钢,烘干:300-350℃×0.5-1h
CR-43
E430-16
0.09
0.60
0.27
0.021
0.003

17.65

300
560
24

用于焊接17%Cr不锈钢,烘干:300-350℃×0.5-1h

类别	品名	AWS型号	熔敷金属化学成分(%)										熔敷金属力学性能				特征与用途
类别	品名	AWS型号	C	Si	Mn	P	S	Ni	Cr	Mo	Cu	Nb+Ta	σ0.2(MPa)	δb(MPa)	δ(%)	Akv(J)	特征与用途
药芯焊棒	TGX-316L	R316LT1-5	0.016	0.87	1.55	0.023	0.004	12.47	18.89	2.32	0.03		440	600	38	0℃:110	用于单面TIG焊的根部焊道，无需背面保护，适用于焊接SUS316和SUS316L钢
	TGX-347	R347T1-5	0.020	0.80	1.60	0.021	0.004	10.21	19.09	0.02	0.03	0.66	460	630	48	0℃:130	用于单面TIG焊的根部焊道，无需背面保护，适用于焊接SUS347和SUS321钢
	TGX-308L	R308LT1-5	0.018	0.80	1.66	0.023	0.005	10.31	19.62	0.02	0.03		450	620	47	-196℃:60	用于单面TIG焊的根部焊道，无需背面保护，适用于焊接SUS304和SUS304L钢
	TGX-309L	R309LT1-5	0.017	0.81	1.52	0.022	0.006	12.62	24.26	0.02	0.03		530	680	32		用于单面TIG焊的根部焊道，无需背面保护，适用于奥氏体钢与铁素体钢的异种钢焊接

焊接法	产品名称	相当规格			规格	熔敷金属物理性能之一例				熔敷金属化学成份之一例（Wt%）					主要用途
		相当规格				抗拉强度	屈服强度	延伸度	冲击值	C	Si	Mn	Ti	其它
		GB	JIS	AWS		MPa	MPa	%	J(℃)	C	Si	Mn	Ti	其它
	JM-49	ER-49-1	-	-	0.8-1.6	565	450	26	90(常温)	0.07	0.6	1.42			适合结构焊接，抗氧化锈皮能力稍强气孔敏感性较小，可做全位置焊接。
	JM-52	ER50-2	-	ER70S-2	0.9-1.2	570	480	26	95(-30)	0.06	0.46	0.85	0.05	Zr:0.01 A1:0.02	适合管件全位置打底焊接，含Ti、AL、Zr等元素，有优越的力学性能。
	JM-53	ER50-3	YGW16	ER70S-3	0.9-1.2	558	470	28	90(-18)	0.08	0.36	0.74			适合焊接板金等薄板工件需焊道平顺精致的高速焊接场合。
	JM-54	ER50-4	YGW12	ER70S-4	0.8-1.6	549	460	32	74(-20)	0.09	0.7	1.06			适合焊接板金等薄板高速焊接及一般结构物，可做全位置焊接。
	JM-56	ER50-6	YGW12	ER70S-6	0.8-2.0	555	430	29	69(-29)	0.08	0.6	1.13			适合结构物焊接，抗氧化锈皮能力稍强，气孔敏感性较小，可做全位置焊接。
GMWA熔化极	JM-70	ER50-6	YGW12	ER70S-6	0.8-2.0	550	425	28	61(-29)	0.08	0.6	1.1		A1:0.006	适合结构物焊接，抗氧化锈皮能力稍强，气孔敏感性较小，可做全位置焊接。
气体保护焊	JM-57	ER50-7	-	ER70S-7	0.8-1.6	545	480	29	61(-29)	0.06	0.54	1.25			适合结构物焊接，抗氧化锈皮能力稍强，气孔敏感性小，可做全位置焊接。
	JM-58	ER50-G	YGW11	ER70S-G	1.0-1.6	580	490	29	120(-20)	0.1	0.57	1.26	适量		适合焊接集装箱、建筑等镀锌钢板，耐气孔性佳，火花飞溅小可做全位置焊接。
	JM-60	ER55-D2Ti	YGW21	ER80S-G	0.8-1.6	650	560	26	62(-29)	0.08	0.61	1.44	适量	Mo:0.37	适合高电流焊接,含适量合金可使飞溅减少,细化晶粒,增加冲击韧性。
	JM-68	ER55-G	-	ER80S-G	1.0-1.6	1.0-1.6	643	605	24	130(-29)	0.07	0.58	1.76	0.12	适合55~60Kg级高强度钢焊接，如桥梁、压力容器、建筑等。
	JM-100	ER69-1	-	ER100S-1	0.8-1.6	700	615	20	78(-51)	0.04	0.33	1.34		Ni:0.67 Mo:0.38	MIG焊丝，用于船体结构的焊接，也适用于Rel大于590Mpa级高强度重要结构钢焊接。
	JM-100C	ER69-3	-	ER100S-G	0.8-1.6	720	615	25	95(-20)	0.09	0.54	1.63		Ni:1.88 Mo:0.46	用于高强度煤矿液压支架的焊接，也适用于Rel大于690Mpa级高强度重要结构钢焊接。
	JM-110	ER76-G	-	ER110S-G	0.8-1.6	820	760	20	82(-50)	0.08	0.42	1.3	Cr:0.23		适用军用钢的焊接，如造船、石油化学、核能电厂等高压设备管件对接及角焊。

H13CrMoA焊丝，上海电力牌焊丝

英国METRODE镍基合金焊接材料

【海焊公司为以下产品的中国总代理】

“质量第一·信誉第一”

曼彻特拥有完整的优质镍基合金焊接材料系列，充分满足大量高精尖工业制造的需求。本系列焊接材料的设计成分优化了产品的焊接工艺和焊缝金属的使用性能，广泛适用于高温、高腐蚀及超低温的使用环境以及异种材料接头的焊接。

曼彻特镍基合金焊接材料所适用的母材不但包括所以著名的专用合金，诸如Inconels,Incloys,Hastelloys,Nicrofers;而且还包括一些新近开发的合金，如617和59类合金等；本节还包括一些适合有色金属的焊接材料，如纯镍、铜镍和蒙乃尔合金等，下表列出了手工电弧焊条，用于TIG，MIG和埋弧焊接的实芯焊丝。

182类合金焊接材料
产品牌号	焊接方法	产品数据	AWS	DIN	适用于镍基材料，如600类合金的焊接也常用于镍基材料，不锈钢和低合金钢之间的异种接头的焊接
NIMROD 132KS	MMA	10-03C	ENiCrFe-1	-
NIMROD 182KS	MMA	10-03A	ENiCrFe-3	EL-NiCr15FeMn
NIMROD 182	MMA	10-03A	ENiCrFe-3	EL-NiCr15FeMn
NIMAX 182	MMA	10-03B	ENiCrFe-3	EL-NiCr15FeMn
NIMROD NC19Nb	MMA	10	-	EL-NiCr19Nb
20.70.Nb	TIG/MIG/SA	15-06A	ERNiCr3	SG-NiCr20Nb
NiCr	Flux	17-06C	-	-

AB类合金焊接材料
NIMROD AKS	MMA	10-04A	ENiCrFe-2	EL-NiCr15MoNb	使用范围与182类焊材相似与182类焊材相比，其焊缝在600°C以上具有更好的高温性能
NIMROD AB	MMA	10-04A	ENiCrFe-2/4	EL-NiCr15MoNb
NIMAX A	MMA	10-04B	ENiCrFe-2	EL-NiCr15MoNb
20.70.Nb	TIG/MIG/SA	15-06A	ERNiCr-3	SG-NiCr20Nb
NiCr	Flux	17-06C	-	-

625类合金焊接材料
NIMROD 625KS	MMA	10-05A	ENiCrMo-3	EL-NiCr20Mo9Nb	焊缝金属具有优良的综合机械性能和耐腐蚀性能适用于相应的625类合金同时也适用于其他高温合金，如601，800等合金 721类焊材适用于6%Mo，825及28合金的焊接
NIMROD 625	MMA	10-05A	ENiCrMo-3	EL-NiCr20Mo9Nb
62-50	TIG/MIG/SA	15-06B	ERNiCrMo-3	SG-NiCr21Mo9Nb
NIMROD 721KS	MMA	10-05E	-	-
72-10	TIG/MIG/SA	15-06N	-	-

C类合金焊接材料
NIMROD C276	MMA	10-07A1	ENiCrMo-4	EL-NiMo15Cr15EW	适用于大多数腐蚀环境含22%Cr的59合金具有优良的耐腐蚀性能 NIMROD C和 C焊条主要用于堆焊，如热作模具的堆焊等 KS型焊条特别适合固定位置管道的焊接
NIMROD C276KS	MMA	10-07A2	ENiCrMo-4	EL-NiMo15Cr15W
HAS C276	TIG	15-06E	ERNiCrMo-4	SG-NiMo16Cr16W
NIMROD C4KS	MMA	10-07C	ENiCrMo-7	EL-NiMo15Cr15Ti
HAS C4	TIG	15-06H	ERNiCrMo-7	SG-NiMo16Cr16Ti
NIMROD 59KS	MMA	10-07F	ENiCrMo-13	EL-NiCr22Mo16
HAS 59	TIG	15-06J	ERNiCrMo-13	SG-Ni23Mo16
NIMROD C	MMA	10	ENiCrMo-5

合金	板材	棒材	焊条	焊丝	无缝管	焊接管	管件	锻件
Hastelloy B-3（ N10675 ）	SB333 B333	SB335 B335	ENiMo-10	ERNiMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-276 (N10276)	SB575 B575	SB574 B574	ENiCrMo-4	ERNiCrMo-4	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-22 (N06022)	SB575 B575	SB574 B574	ENiCrMo-10	ERNiCrMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-2000 (N06200)	SB575 B575	SB574 B574	ENiCrMo-17	ERNiCrMo-17	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy D-205
Hastelloy G-30 (N06030)	SB582 B582	SB581 B581	ENiCrMo-11	ERNiCrMo-11	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy G-35 (N06035)	B575	B574			B622	B619 B626	B366	B462
ULTIMET (R31233)	B818	B815
Hastelloy B (N10001)	SB333 B333	SB335 B335	ENiMo-10
Hastelloy X (N06002)	SB435 B435 AMS5536	SB572 B572 AMS 5754	ENiCrMo-2	ERNiCrMo-2	SB622 B622	SB619/B619	B366	AMS 5754
Haynes 25 (R30605)	AMS 5537	AMS5759	AMS5797	AMS5796		B619/B626		AMS5759
Haynes HR-120 (N08120)	AMS5619 SB409 B409	SB408 B408			SB407 B407	SB514/B514 SB515/B515	SB366 B366	SB564 B564
Haynes HR-160 (N12160)	SB435 B435	SB572 B572			SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Haynes 188（ R30188 ）	AMS5608	AMS5772		AMS5801				AMS5772
Haynes 214 (N07041)
Haynes 230 (N06230)	SB435 B435 AMS5878	SB572 B572 AMS5891			SB622/B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564 AMS 5891
Haynes 230-W (N06231)				ERNiCrWMo-1 AMS5839
Haynes 242 (N10242)	SB434 B434	SB573 B573			SB622	SB619/B619 B626	B366	SB564 B564
Haynes 556 (R30556)	SB435 B435 AMS5874	SB572 B572 AMS5877		ER3556 AMS5831	SB622/B622	SB619/B619 SB626/B626	SB366 B366	AMS5877
Haynes 625 (N06625)	SB443 B443 AMS5666	SB446 B446 AMS5599		ERNiCrMo-3 AMS5837	AMS5581 SB444/B444	AMS5881 SB704/B704 SB705/B705	SB366 B366	AMS5666
Haynes 718 (N07718)	AMS5596 AMS5597	AMS5662 AMS5664 SB637 B637		ERNiCrFeCr-2 AMS 5832	AMS5589 AMS5590			AMS5662 AMS5664
B =执行标准 ASTM SB = 执行标准 ASME 焊丝焊条为 AWS 标准 AMS 为 SAE 标准

焊条

1N12	ENICrMo-3	1N12	用于焊接镍铬钼合金,如625 800 801 825 600
8N12	ENICrFe-3	8N12H	用于镍铬钼合金自身的焊接,钢及碳钢的焊接
4N1A	ENICrFe-2	4N1A	用于奥氏体钢,铁素体钢和高镍合金各种类型的焊接,也可用于9%镍合金的焊接
9N10	ENiCu-7	9N10	主要用于镍钢合金自身的焊接以及它们和钢之间的焊接
352	ENICrFe-7	N/A	焊接镍铬铁合金690(UNS N06690)自身
C-276	ENICrMo-4	N/A	焊接C-276合金自身以及大多数其它镍基合金
617	ENICrCoMo-1	N/A	焊接镍铬钴钼合金以及焊接各种不同的高温合金

合金	板材	棒材	焊条	焊丝	无缝管	焊接管	管件	锻件
Hastelloy B-3（ N10675 ）	SB333 B333	SB335 B335	ENiMo-10	ERNiMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-276 (N10276)	SB575 B575	SB574 B574	ENiCrMo-4	ERNiCrMo-4	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-22 (N06022)	SB575 B575	SB574 B574	ENiCrMo-10	ERNiCrMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-2000 (N06200)	SB575 B575	SB574 B574	ENiCrMo-17	ERNiCrMo-17	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy D-205
Hastelloy G-30 (N06030)	SB582 B582	SB581 B581	ENiCrMo-11	ERNiCrMo-11	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy G-35 (N06035)	B575	B574			B622	B619 B626	B366	B462
ULTIMET (R31233)	B818	B815
Hastelloy B (N10001)	SB333 B333	SB335 B335	ENiMo-10
Hastelloy X (N06002)	SB435 B435 AMS5536	SB572 B572 AMS 5754	ENiCrMo-2	ERNiCrMo-2	SB622 B622	SB619/B619	B366	AMS 5754
Haynes 25 (R30605)	AMS 5537	AMS5759	AMS5797	AMS5796		B619/B626		AMS5759
Haynes HR-120 (N08120)	AMS5619 SB409 B409	SB408 B408			SB407 B407	SB514/B514 SB515/B515	SB366 B366	SB564 B564
Haynes HR-160 (N12160)	SB435 B435	SB572 B572			SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Haynes 188（ R30188 ）	AMS5608	AMS5772		AMS5801				AMS5772
Haynes 214 (N07041)
Haynes 230 (N06230)	SB435 B435 AMS5878	SB572 B572 AMS5891			SB622/B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564 AMS 5891
Haynes 230-W (N06231)				ERNiCrWMo-1 AMS5839
Haynes 242 (N10242)	SB434 B434	SB573 B573			SB622	SB619/B619 B626	B366	SB564 B564
Haynes 556 (R30556)	SB435 B435 AMS5874	SB572 B572 AMS5877		ER3556 AMS5831	SB622/B622	SB619/B619 SB626/B626	SB366 B366	AMS5877
Haynes 625 (N06625)	SB443 B443 AMS5666	SB446 B446 AMS5599		ERNiCrMo-3 AMS5837	AMS5581 SB444/B444	AMS5881 SB704/B704 SB705/B705	SB366 B366	AMS5666
Haynes 718 (N07718)	AMS5596 AMS5597	AMS5662 AMS5664 SB637 B637		ERNiCrFeCr-2 AMS 5832	AMS5589 AMS5590			AMS5662 AMS5664
B =执行标准 ASTM SB = 执行标准 ASME 焊丝焊条为 AWS 标准 AMS 为 SAE 标准

8”以下管材为固溶退火，酸洗交货巴氏合金焊丝 Sn4-4、Sn8-4锑铜焊丝

合金	板材	棒材	焊条	焊丝	无缝管	焊接管	管件	锻件
Hastelloy B-3（ N10675 ）	SB333 B333	SB335 B335	ENiMo-10	ERNiMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-276 (N10276)	SB575 B575	SB574 B574	ENiCrMo-4	ERNiCrMo-4	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-22 (N06022)	SB575 B575	SB574 B574	ENiCrMo-10	ERNiCrMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-2000 (N06200)	SB575 B575	SB574 B574	ENiCrMo-17	ERNiCrMo-17	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy D-205
Hastelloy G-30 (N06030)	SB582 B582	SB581 B581	ENiCrMo-11	ERNiCrMo-11	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy G-35 (N06035)	B575	B574			B622	B619 B626	B366	B462
ULTIMET (R31233)	B818	B815
Hastelloy B (N10001)	SB333 B333	SB335 B335	ENiMo-10
Hastelloy X (N06002)	SB435 B435 AMS5536	SB572 B572 AMS 5754	ENiCrMo-2	ERNiCrMo-2	SB622 B622	SB619/B619	B366	AMS 5754
Haynes 25 (R30605)	AMS 5537	AMS5759	AMS5797	AMS5796		B619/B626		AMS5759
Haynes HR-120 (N08120)	AMS5619 SB409 B409	SB408 B408			SB407 B407	SB514/B514 SB515/B515	SB366 B366	SB564 B564
Haynes HR-160 (N12160)	SB435 B435	SB572 B572			SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Haynes 188（ R30188 ）	AMS5608	AMS5772		AMS5801				AMS5772
Haynes 214 (N07041)
Haynes 230 (N06230)	SB435 B435 AMS5878	SB572 B572 AMS5891			SB622/B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564 AMS 5891
Haynes 230-W (N06231)				ERNiCrWMo-1 AMS5839
Haynes 242 (N10242)	SB434 B434	SB573 B573			SB622	SB619/B619 B626	B366	SB564 B564
Haynes 556 (R30556)	SB435 B435 AMS5874	SB572 B572 AMS5877		ER3556 AMS5831	SB622/B622	SB619/B619 SB626/B626	SB366 B366	AMS5877
Haynes 625 (N06625)	SB443 B443 AMS5666	SB446 B446 AMS5599		ERNiCrMo-3 AMS5837	AMS5581 SB444/B444	AMS5881 SB704/B704 SB705/B705	SB366 B366	AMS5666
Haynes 718 (N07718)	AMS5596 AMS5597	AMS5662 AMS5664 SB637 B637		ERNiCrFeCr-2 AMS 5832	AMS5589 AMS5590			AMS5662 AMS5664
B =执行标准 ASTM SB = 执行标准 ASME 焊丝焊条为 AWS 标准 AMS 为 SAE 标准

合金	板材	棒材	焊条	焊丝	无缝管	焊接管	管件	锻件
Hastelloy B-3（ N10675 ）	SB333 B333	SB335 B335	ENiMo-10	ERNiMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-276 (N10276)	SB575 B575	SB574 B574	ENiCrMo-4	ERNiCrMo-4	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-22 (N06022)	SB575 B575	SB574 B574	ENiCrMo-10	ERNiCrMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-2000 (N06200)	SB575 B575	SB574 B574	ENiCrMo-17	ERNiCrMo-17	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy D-205
Hastelloy G-30 (N06030)	SB582 B582	SB581 B581	ENiCrMo-11	ERNiCrMo-11	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy G-35 (N06035)	B575	B574			B622	B619 B626	B366	B462
ULTIMET (R31233)	B818	B815
Hastelloy B (N10001)	SB333 B333	SB335 B335	ENiMo-10
Hastelloy X (N06002)	SB435 B435 AMS5536	SB572 B572 AMS 5754	ENiCrMo-2	ERNiCrMo-2	SB622 B622	SB619/B619	B366	AMS 5754
Haynes 25 (R30605)	AMS 5537	AMS5759	AMS5797	AMS5796		B619/B626		AMS5759
Haynes HR-120 (N08120)	AMS5619 SB409 B409	SB408 B408			SB407 B407	SB514/B514 SB515/B515	SB366 B366	SB564 B564
Haynes HR-160 (N12160)	SB435 B435	SB572 B572			SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Haynes 188（ R30188 ）	AMS5608	AMS5772		AMS5801				AMS5772
Haynes 214 (N07041)
Haynes 230 (N06230)	SB435 B435 AMS5878	SB572 B572 AMS5891			SB622/B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564 AMS 5891
Haynes 230-W (N06231)				ERNiCrWMo-1 AMS5839
Haynes 242 (N10242)	SB434 B434	SB573 B573			SB622	SB619/B619 B626	B366	SB564 B564
Haynes 556 (R30556)	SB435 B435 AMS5874	SB572 B572 AMS5877		ER3556 AMS5831	SB622/B622	SB619/B619 SB626/B626	SB366 B366	AMS5877
Haynes 625 (N06625)	SB443 B443 AMS5666	SB446 B446 AMS5599		ERNiCrMo-3 AMS5837	AMS5581 SB444/B444	AMS5881 SB704/B704 SB705/B705	SB366 B366	AMS5666
Haynes 718 (N07718)	AMS5596 AMS5597	AMS5662 AMS5664 SB637 B637		ERNiCrFeCr-2 AMS 5832	AMS5589 AMS5590			AMS5662 AMS5664
B =执行标准 ASTM SB = 执行标准 ASME 焊丝焊条为 AWS 标准 AMS 为 SAE 标准

合金	板材	棒材	焊条	焊丝	无缝管	焊接管	管件	锻件
Hastelloy B-3（ N10675 ）	SB333 B333	SB335 B335	ENiMo-10	ERNiMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-276 (N10276)	SB575 B575	SB574 B574	ENiCrMo-4	ERNiCrMo-4	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-22 (N06022)	SB575 B575	SB574 B574	ENiCrMo-10	ERNiCrMo-10	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy C-2000 (N06200)	SB575 B575	SB574 B574	ENiCrMo-17	ERNiCrMo-17	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy D-205
Hastelloy G-30 (N06030)	SB582 B582	SB581 B581	ENiCrMo-11	ERNiCrMo-11	SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Hastelloy G-35 (N06035)	B575	B574			B622	B619 B626	B366	B462
ULTIMET (R31233)	B818	B815
Hastelloy B (N10001)	SB333 B333	SB335 B335	ENiMo-10
Hastelloy X (N06002)	SB435 B435 AMS5536	SB572 B572 AMS 5754	ENiCrMo-2	ERNiCrMo-2	SB622 B622	SB619/B619	B366	AMS 5754
Haynes 25 (R30605)	AMS 5537	AMS5759	AMS5797	AMS5796		B619/B626		AMS5759
Haynes HR-120 (N08120)	AMS5619 SB409 B409	SB408 B408			SB407 B407	SB514/B514 SB515/B515	SB366 B366	SB564 B564
Haynes HR-160 (N12160)	SB435 B435	SB572 B572			SB622 B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564
Haynes 188（ R30188 ）	AMS5608	AMS5772		AMS5801				AMS5772
Haynes 214 (N07041)
Haynes 230 (N06230)	SB435 B435 AMS5878	SB572 B572 AMS5891			SB622/B622	SB619/B619 SB626/B626	SB366 B366	SB564 B564 AMS 5891
Haynes 230-W (N06231)				ERNiCrWMo-1 AMS5839
Haynes 242 (N10242)	SB434 B434	SB573 B573			SB622	SB619/B619 B626	B366	SB564 B564
Haynes 556 (R30556)	SB435 B435 AMS5874	SB572 B572 AMS5877		ER3556 AMS5831	SB622/B622	SB619/B619 SB626/B626	SB366 B366	AMS5877
Haynes 625 (N06625)	SB443 B443 AMS5666	SB446 B446 AMS5599		ERNiCrMo-3 AMS5837	AMS5581 SB444/B444	AMS5881 SB704/B704 SB705/B705	SB366 B366	AMS5666
Haynes 718 (N07718)	AMS5596 AMS5597	AMS5662 AMS5664 SB637 B637		ERNiCrFeCr-2 AMS 5832	AMS5589 AMS5590			AMS5662 AMS5664
B =执行标准 ASTM SB = 执行标准 ASME 焊丝焊条为 AWS 标准 AMS 为 SAE 标准

MRO消耗品、易耗品 > 焊接耗材 > 焊条 >

Category 类别	Trade- Mark 牌号	Equivalent to China Standard 相当国标	Characteristics & application 特性和用途	Equivalent to AWS 相当AWS
Hard-surfacing 硬面堆焊	D 667	EDZCr-B-15	HRc≥48. Resistance to wear, gas corrosion and oxidation. Hardfacing of blast furnace hopper and cracker part. HRc≥48，耐磨、耐气蚀、抗氧化。堆焊高炉料钟、破碎机件
	D 802	EDCoCr-A-03	HRc38-47. Resistance to heat, wear and corrosion. Hardfacing of high temperature part such as the edge of thermo-cutter. HRc38-47，耐热、耐蚀、耐磨。堆焊高温工件如热剪切刀刃	ECoCr-A
	D 812	EDCoCr-B-03	HRc45-50. Resistance to heat, wear and corrosion. Hardfacing of high temperature part such as internal-combustion engine valve. HRc45-50，耐热、耐蚀、耐磨。堆焊高温工件如内燃机阀	ECoCr-B
	D 822		HRc≥53. Resistance to Wear and heat, bad shock resistance. Hardfacing of rotating blade wheel of boiler. HRc≥53，耐热、耐磨，但抗冲击性差。堆焊锅炉旋转叶轮
	D 832	EDCoCr-C-03	HRc≥50. Wear and heat resistance. Hardfacing of high temperature part such as hot-rolling guided way. HRc≥50，耐热、耐磨。堆焊高温工件如热轧导轨	ECoCr-C
	D 842	EDCoCr-D-03	HRc28-38. Corrosion and thermo-fatigue resistance, work harding. Hardfacing of hot forging die. HRc28-38，耐蚀、抗热疲劳，具有加工硬化性。堆焊热锻模
Cast iron 铸铁	Z 308	EZNi	Pure nickel, excellent general properties. Used to weld thin cast iron part and repair welding machined surface, such as guided way of machine tool. 纯镍，综合性能好。铸铁薄件及加工面补焊用，如机床导卫	ENi-Cl
	Z 408	EZNiFe	Iron nickel, high strength and excellent ductility. Repair welding of important gray cast iron and nodular cast iron, such as cylinder cap. 镍铁，强度高、塑性好。重要灰铸铁及球铁焊补用，如汽缸盖	ENiFe-Cl
	Z 508	EZNiCu-1	Copper nickel, good machinability and bad crack resistance. Repair welding of sand hole and gray cast iron machined surface subject to no load. 镍铜，易加工，但抗裂性较差。不受力的灰铸铁加工面及砂眼补焊	ENiCu-B
Copper alloys 铜合金	Cu 107	ECu	Red copper, atmosphere and sea water corrosion and excellent electric conductivity. Welding of red copper such as electrical copper row. 紫铜，耐大气，海水腐蚀，导电性好。紫铜焊接用，如导电铜排	ECu
	Cu 207	ECuSi	Silicon bronze, corrosion resistance and high strength. Welding of copper, silicon bronze and brass. 硅青铜，耐蚀、强度高。铜、硅青铜及黄铜焊接用	ECuSi
	Cu 227	ECuSnB	Tin phosphor bronze, corrosion resistance and high strength. Welding of copper, silicon bronze and brass. 锡磷青铜，耐蚀、强度高。铜、硅青铜及黄铜焊接用	ECuSn-C
	Cu 237	ECuAl	Aluminum bronze, wear and corrosion and high strength. Welding or surfacing of copper alloys. 铝青铜，耐磨、耐蚀，强度高。铜合金焊接或堆焊用	ECuAl-A2
Aluminum alloys 铝合金	Al 109	TAl	Pure aluminum, excellent corrosion resistance and middle strength. Welding of pure aluminum. 纯铝，耐蚀性好，但强度不高，纯铝焊接用	E1100
	Al 209	TAlSi	Silicon aluminum, good crack resistance and wide range of usage. Welding of aluminum alloys other than aluminum magnesium alloys. 铝硅，抗裂性好，通用性大。铝合金焊接用，不宜焊接铝镁合金	E4043
	Al 309	TAMn	Manganese aluminum, corrosion resistance and high strength. Welding of aluminum alloys. 铝锰，强度高，耐蚀。铝合金焊接用	E3003
Nickel alloys 镍合金	Ni 102	ENi-1	Pure nickel. Welding and surfacing of nickel and nickel to steel. 纯镍，用于镍、镍与钢的焊接与堆焊	ENi-1
Nickel alloys 镍合金	Ni 207	ENiCu-7	Copper nickel. Welding and surfacing of copper nickel and copper nickel to steel. 镍铜，用于镍铜、镍铜与钢的焊接与堆焊	ENiCu-7

Category 类别	Trade mark 牌号	Chemical composition 主要成份(%)	Characteristics & application 特性和用途	Equivalent to AWS 相当AWS
Hardfacing 硬面堆焊	S 101	C3 Cr28 Ni4 Si3.5 Fe Rem.	HRc48-54. Resistance to wear, gas corrosion and oxidation. Hardfacing of bucket tooth and case pump. HRc48-54，耐磨、耐气蚀、抗氧化。堆焊铲斗齿，泵套
	S 111	C1 Cr29 W5 Co Rem.	HRc38-47. Resistance to wear and corrosion at high-temperature. Hardfacing of high temperature and pressure valve. HRc38-47，高温下耐磨、耐蚀。堆焊高温高压阀门	ECoCr-A
	S 112	C1.5 Cr29 W8 Co Rem.	HRc45-50. Resistance to wear and corrosion at high-temperature. Hardfacing of valve and hot-rolling pass. HRc45-50，高温下耐磨、耐蚀。堆焊阀门，热轧孔型	ECoCr-B
	S 113	C2.5 Cr30 W17 Co Rem.	HRc≥55. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of screw charging carriage. HRc≥55，高温下耐磨、耐热，但抗冲击性差。堆焊螺旋送料机用
	S 114	C2.5 Cr30 W12 Co Rem.	HRc≥53. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of three-cone bit. HRc≥53，高温下耐磨、耐热，但抗冲击较差。堆焊牙轮钻头	ECoCr-C
Copper alloys 铜合金	S 201	Sn1 Si0.3Mn0.3 Cu Rem.	Good mechanical properties and crack resistance. Gas welding and argon arc welding of red copper. 机械性能好，抗裂性好。紫铜气焊及氩弧焊用	ERCu
	S 211	Si3 Mn1 Cu Rem.	Good mechanical properties. Argon arc welding of copper alloys and MIG brazing of steel. 机械性能好，铜合金氩弧焊及钢的MIG钎焊用	ERCuSi-Al
	S 212	Sn5 Cu Rem.	Wear resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨性好。铜合金氩弧焊及钢的堆焊用	ERCuSn-A
	S 213	Sn8 Cu Rem.	Wear resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨性好。铜合金氩弧焊及钢的堆焊用	ERCuSn-C
	S 214	Al7.5 Cu Rem.	Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用	ERCuAl-A1
	S 215	Al9 Cu Rem.	Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用	ERCuAl-A2
	S 221	Cu60 Sn1 Si0.3 Zn Rem.	Melting point is about 890℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔点约890℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
	S 221F	Cu60 Sn1 Si 0.3 Zn Rem.	S221 welding rod coated with flux. 外涂焊剂的S221焊丝
	S 222	Cu58Sn0.9Si0.1 Fe0.8 Zn Rem.	Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔点约880℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁	RBCuZn-C
	S 222F	Cu58Sn0.9Si0.1 Fe0.8 Zn Rem.	S222 welding rod coated with flux. 外涂焊剂的S222焊丝	RBCuZn-C
	S 223	Cu59 Sn0.6 Zn Rem.	Melting point is about 900℃. Braze welding of copper, steel and cast iron. 熔点约900℃。铜、钢、铸铁钎焊用	RBCuZn-A
	S 224	Cu62 Si0.5 Zn Rem.	Melting point is about 905℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔点约905℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
Copper alloys 铜合金	S 225	Cu48 Ni10 Zn Rem.	Melting point is about 935℃ and high strength. Braze welding of steel, nickel and carbide alloys. 熔点约935℃。高强度,钎焊钢、镍及硬质合金用	RBCuZn-D
	S 225F	Cu48 Ni10 Zn Rem.	S225 welding rod coated with flux. 外涂焊剂的S225焊丝	RBCuZn-D
	S 226	Cu60 Sn0.3 Si0.2 Zn Rem.	Melting point is about 900℃. Gas welding of brass, also braze welding of copper, steel and cast iron. 熔点约900℃。黄铜气焊用，也可钎焊铜、钢、铸铁
	S 227	Cu58Sn0.9Ni0.5 Si0.1 Fe0.8 Zn Rem.	Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔点880℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁	RBCuZn-B
	S 229	Cu55 Ni6 Mn4 Zn余	Melting point is about 920℃, high strength. Braze welding of steel, nickel and hard carbide. 熔点约920℃。高强度,钎焊钢、镍及硬质合金用
Aluminum alloys 铝合金	S 301	Al≥99.5	Good ductility and corrosion resistance. Gas welding and argon arc welding of pure aluminum. 塑性好、耐蚀。纯铝气焊、氩弧焊用	ER1100
	S 311	Si5 Al Rem.	Corrosion resistance, wide range of usage. Gas welding and argon arc welding of aluminum alloys other than high magnesium alloys. 抗裂性好，通用性大。铝合金气焊、氩弧焊用。不宜用高镁合金	ER4043
	S 321	Mn1.3 Al Rem.	Good corrosion resistance, weldability and ductility. Gas welding and argon arc welding of aluminum alloys. 良好的耐蚀性、可焊性及塑性。铝合金气焊、氩弧焊用
	S 331	Mg5 Mn0.4 Al Rem.	Corrosion resistance and high strength. Argon arc welding of aluminum alloys. 耐蚀，强度高。铝合金氩弧焊用	ER5183

Category 类别	Trade-mark 牌号	Specification 规格	Melting Point 熔点(℃)	Chemical composition 主要成份(%)	Application 用途	Equivalent to AWS 相当AWS
Copper zinc 铜锌	L103	Wire & rod 丝	885-888	Cu54 Zn Rem.	Brazing of copper, bronze and steel, subjected to low load. 钎焊铜、青铜和钢等受力不大工件
Copper zinc 铜锌	L104	Foil 箔	890-930	Cu57 Mn2 Co2 Zn Rem.	Brazing of carbide cutting tool. 钎焊硬质合金刀具
Copper phosphorus 铜磷	L201	Cast rod, wire & rod, powder 铸条、丝、粉	710-800	P7 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-2
	L204	Cast rod, wire 铸条、丝	640-815	P5 Ag15 Cu Rem.	Brazing of copper, copper alloys, silver and molybdenum etc. 钎焊铜及铜合金、银、钼等金属。	BCuP-5
	L205	Cast rod, wire & rod, powder 铸条、丝、箔	640-800	P6 Ag5 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-3
	L207	Cast rod, wire & rod 铸条、丝	640-770	P7 Ag5 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-7
	L209	Cast rod, wire 铸条、丝	684-710	P7 Ag2 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金。	BCuP-6
Silver base 银基	L302	Wire & rod 丝	745-775	Ag25 Cu40 Zn Rem.	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
	L303	Wire & rod 丝	660-725	Ag45 Cu30 Zn余	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-5
	L303F	Flux coated rod 涂药丝	660-725	Ag45 Cu30 Zn Rem.	L303 coated with flux, the same application as L303. 外涂钎剂的L303，用途与L303相同	BAg-5
	L304	Foil 箔	690-775	Ag50 Cu34 Zn Rem.	Brazing of copper, copper alloys and steel etc. 钎焊铜及铜合金、钢等	BAg-6
	L308	Wire & rod 丝	779-780	Ag72 Cu Rem.	Brazing of copper and nickel under vacuum or reducing protective atmosphere. 铜和镍的真空或还原保护气氛钎焊	BAg-8
	L312	Wire & rod 丝	595-605	Ag40.Cu.Zn.Cd	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
	L313	Wire & rod 丝	625-635	Ag50.Cu.Zn.Cd	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-1a
	L321	Wire & rod 丝	615-650	Ag56.Cu.Zn.Sn	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-7
	L323	Wire & rod 丝	665-755	Ag30.Cu.Zn.Sn	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
	L325	Wire & rod 丝	645-685	Ag45.Cu.Zn.Sn	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-36
	L326	Wire & rod 丝	650-720	Ag38.Cu.Zn.Sn	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-34
Aluminum base 铝基	L400	Cast rod, wire & rod 铸条、丝	577-582	Si11.5 Al Rem.	Brazing of aluminum and aluminum alloys. 铝及铝合金的钎焊	BAlSi-4
Aluminum base 铝基	L401	Cast rod 铸条	525-535	Si5 Cu28 Al Rem.	Brazing of aluminum and aluminum alloys. 铝及铝合金的钎焊
Tin lead 锡铅	L600	Wire & rod 丝	183-185	Sn60 Sb≤0.8 Pb Rem.	Soldering of fusible metals and heat-treated part. 易熔金属及热处理件的钎焊	60Sn
	L601	Wire & rod 丝	183-227	Sn18 Sb2 Pb Rem.	Soldering of copper, copper alloys and galvanized iron plain sheet. 铜及铜合金、镀锌铁皮的钎焊。	18Sn
	L602	Wire & rod 丝	183-256	Sn30 Sb2 Pb Rem.	Soldering of copper, brass, copper alloys and galvanized iron plain sheet. 铜、黄铜、铁、镀锌铁皮的钎焊	30Sn
	L603	Wire & rod 丝	183-235	Sn40 Sb2 Pb Rem.	Soldering of copper, copper alloys, steel and zinc parts. 铜及铜合金、钢、锌制零件的钎焊	40Sn
	L604	Wire & rod 丝	183-222	Sn90 Sb≤0.15 Pb Rem.	Soldering of copper and steel for food and medicine field. 食品、医疗所需铜、钢等金属的钎焊	90Sn
	L605	Wire & rod 丝	232-240	Ag5 Sn95	Soldering of copper and steel for electrical and food field. 电器、食品所需铜、钢等金属的钎焊
	L608	Wire & rod 丝	295-305	Sn5.5 Ag2.5 Pb Rem.	Soldering of copper, copper alloys, steel and stainless steel. 铜及铜合金、钢及不锈钢的钎焊
Nickel base 镍基	L702	Powder 粉	970-1000	Cr7 B3 Si4 Ni Rem.	Brazing of stainless steel under vacuum or protective atmosphere. 不锈钢真空或保护气氛钎焊	BNi-2

Category 类别	Trade-mark 牌号	Product name 名称	Characteristics & application 特性和用途
Gas welding 气焊	CJ301	Copper gas welding flux 铜气焊熔剂	Melting point is about 650℃, flux for gas welding and brazing of copper and copper alloys. 熔点约650℃，铜及铜合金气焊或钎焊的助熔剂
Gas welding 气焊	CJ401	Aluminum gas welding flux 铝气焊熔剂	Melting point is about 560℃, flux for gas welding of aluminum and aluminum alloys. 熔点约560℃，铝及铝合金气焊的助熔剂
Silver brazing 银钎焊	QJ101	Silver brazing flux 银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 550-750℃. 在550-750℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
	QJ102	Silver brazing flux 银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃. 在600-850℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
	QJ102A	Silver brazing flux 银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃. Non agglomeration. 在600-850℃范围钎焊铜及铜合金、钢及不锈钢。不易结块
	QJ112	Silver brazing paste flux 膏状银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 600-850℃. 在600-850℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
	QJ103	Silver brazing flux 银钎焊熔剂	Brazing flux of copper, copper alloys, steel and stainless steel within 550-750℃. 在550-750℃范围钎焊铜及铜合金、钢及不锈钢的助熔剂
Aluminum brazing 铝钎焊	QJ201	Aluminum brazing flux 铝钎焊熔剂	Brazing flux of aluminum and aluminum alloys within 450-620℃. 在450-620℃范围钎焊铝及铝合金的助熔剂
Aluminum brazing 铝钎焊	QJ207	Aluminum brazing flux 铝钎焊熔剂	Brazing flux of aluminum and aluminum alloys within 560-620℃. 在560-620℃范围钎焊铝及铝合金的助熔剂

Category 类别	Trade- mark 牌号	Chemical composition 化学成份(%)	Hardness 硬度	Application 用途
Oxy- Acetylene Flame spray- using 氧乙炔焰喷焊	F103	Cr10 B1.5 Si3 Ni Rem.	HRc 25	Spray-fusing of cast iron parts,, such as die for glass, cylinder, and guide. 铸铁件的喷焊，如玻璃模具，汽缸、导轨
	F101	Cr10 B2.5 Si3 Ni Rem.	HRc 45	Spray-fusing of parts resistance to wear and corrosion, such as valve, the rotator and piston of pump. 耐磨、耐蚀件的喷焊，如阀门、泵转子、泵柱塞
	F101Fe	Cr10 B2.5 Si3 Fe10 Ni Rem.	HRc 45	Spray-fusing of corrosion-resistant parts, such as axle and stigma. 耐磨件的喷焊，如轴类、汽门
	F102	Cr16 B4 Si4 Ni Rem.	HRc 60	Spray-fusing of parts resistance to wear, corrosion and high temperature oxidation, such as die and piston. 耐磨、耐蚀、抗高温氧化工件的喷焊，如模具、柱塞
	F102Fe	Cr16 B4 Si4 Fe15 Ni Rem.	HRc 60	Spray-fusing of corrosion-resistant parts, such as axle and cold die. 耐磨件的喷焊，如轴类、冷模具
	F105	F102+50%WC	HRc 60	Spray-fusing of parts resistance to grain-wear , such as guide plate, scraper and blade of fan. 抗磨粒磨损场合的喷焊，如导板、刮板、风机叶片
	F105Fe	F102Fe+35%WC	HRc 60	Spray-fusing of parts resistance to grain-wear, such as guide plate, scraper and blade of fan. 抗磨粒磨损场合的喷焊，如导板、刮板、风机叶片
	F108	F102+80%WC	HRc 60	Spray-fusing of parts resistance to strong grain-wear and free machining, such as harrow teeth of dredger. 抗强烈磨粒磨损，无需加工场合的喷焊，如挖泥船耙齿
	F301	Cr5 B4 Si4 Ni30 Fe Rem.	HRc 45	Spray-fusing of vulnerable parts of agricultural machinery and mining machinery, such as gear and axletree. 农机,矿山机械易损件的喷焊，如齿轮，车轴
	Track iron powder 轨铁粉	Cr5 B1.5 Si3 Ni30 Fe Rem.	HRc 28	Repair spray-fusing of defects such as scratch and concavity of railroad track. 铁路钢轨擦伤、低塌等缺陷的修复喷焊
Oxy-acetylene flame spraying 氧乙炔焰喷涂	F111	Cr5 B1.5 Si3 Ni30 Fe Rem.	HB 150	Spraying of bearing and cutting parts etc. 轴承、切削件等的喷涂
	F113	Cr10 B1.5 Si3 Ni Rem.	HB 250	Spray-fusing or spraying, such as roll, piston and axle of wear and corrosion resistance. 喷涂亦可喷焊，如滚筒、柱塞、耐蚀耐磨轴等
	F313	Cr15 B1.5 Fe Rem.	HB 250	Spraying of dryer of papermaking and axle. 造纸烘缸、轴类的喷涂
	F314	Cr18 Ni9 B1.5 Fe Rem.	HB 250	Spraying of axle. 轴类喷涂
	F412	Sn10 P0.3 Cu Rem.	HB 80	Spraying of axle and bearing. 轴、轴承的喷涂
	F512	复合Al5Ni95		Backing spray of transition layer between base and working layer. 喷涂层的基体与工作层之间过渡（打底）层用喷涂
PTA hardfacing 等离子弧喷焊	F221	Cr26 W5 B0.7 Co Rem.	HRc 43	PTA hardfacing of sealing surface of high temperature and high pressure valve and the edge of hot shearing tool. 高温高压阀门密封面、热剪切刃口的等离子喷焊
	F223	Cr21 W5 B1.5 Co Rem.	HRc 40	PTA hardfacing of parts resistance to wear and corrosion at high temperature, such as valve under high temperature and high pressure, and blower. 高温下耐磨耐蚀件的喷焊，如高温高压阀门、鼓风机
	F321	Cr13 B1.5 Si1 Fe Rem.	HRc 45	PTA hardfacing of corrosion-resistant parts under mid-temperature and mid-pressure, such as stop-plate etc. 中温中压阀门的闸板及其他耐磨件的等离子喷焊
	F322	Cr23 Ni13 Si5 B1 Fe Rem.	HRc 40	PTA hardfacing of corrosion-resistant parts under mid-temperature and mid-pressure, such as valve base etc. 中温中压阀门的阀座及其他耐磨件的等离子喷焊
	F422	Sn10 P0.3 Cu Rem.	HB 80	PTA hardfacing of axle and bearing etc. 轴、轴承等离子喷焊