输入电源:DC11.0~18.0 Volt
充电功率: 最大 50W x 2
放电功率： 5W x 2
充电电流: 0.1~5.0A x2
放电电流: 0.1~1.0A x2
单个电池的电流: 300mAh/cell
充镍氢,镍铬节数: 1~15 cell x2
充锂离子,锂聚合物,锂铁电池节数: 1~6 *2/最大12S
铅蓄电池: 2V~20V x2
重量: 430g(净重)
尺寸: 160×135×23mm
Imax B610 Twins
Charger | Imax RC B610 Twins Introduction If you have been searching for one charger can charge two batteries at once, look no further than the IMAXRC B610Twins. It is a latest professional & rapid charger of 200W /each with dual output, totally output 400W. B610Twins is able to service multiple types of batteries, such as NiCd, NiMH, LiPO, Li-ION/LiFe and Lead Acid batteries. | Optimized operation software B610Twins features an AUTO function that controls the charge rate during charging and discharging. For Lithium batteries, this can prevent overcharging which may lead to an explosion due to the user's setting the charge rate improperly. It will disconnect the circuit automatically and initiate an alarm if there is any malfunction. All the operating modes of this charger are controlled through two way communication, between the charger and the battery to achieve maximum safety. All the settings can be configured by the user. | Internal independent lithium battery balancer B610Twins employs an inpidual cell voltage balancer. It isn't necessary to connect an external balancer for balancer charging. |
| SPECIFICATIONS - Operation voltage range :DC: 11.0~18.0 Volt
- Circuit power: Max :Charge power 2*200Watts
- Max :Discharge power 2*25
- Charge current range :(0.1~10A)
- Discharge current range :2*(0.1~5A)
- Current drain for balancing Li-Po/Lon/Fe :200Ma/cell
- Li-ion/Fe/Polymer cell count :(1~6cells)
- NiCd/NiMH battery cell count :1~18cells
- Pb battery voltage :2V~24V
- Net weight :350g
- Dimension :160*200*60mm
| COMPARISON WITH OTHER CHARGERS: | Charger | Cells for LI battery | Charge current range | Circuit power | AC/DC | Dual output | | Imax B610Twins | 1-6cells | 2*(0.1~10A) | 2*200Watts | DC | YES | | Imax B6 Twins | 1-6cells | 2*(0.1~5A) | 2*50Watts | DC | YES |
| Imax B610 Includes - - IMAXRC B610Twins
- - Manual book
- - 6 kinds of wires : Tamiya charging cable, FutabaRX charging cable, Glow charging cable, Crocodile clip charging cable, JST/BEC charging cable, Dean charging cable( two pcs)
- - One pair 6PIN adapter
- - One pair Crocodile clip
|
|
How to use 1, Using the power cord, connect the charger to the 110~240VAC mains electricity (usual household wall socket).The 2control LED on the charger light green ,the charger is in standby mode. | 2. Connect the battery to the charger as following, and push "on/off" button the charger will enter charge state, then 2 LED turn red. Figure 1: If a LED is flashing red, it means that the corresponding cell has a low voltage or connects with charger improperly. Check the connection state between balance port and charger, or check the voltage of corresponding battery cell. If battery is defective, discontinue use of this battery immediately. | 3. When battery is fully charged and balanced, the LED will turn green. The charger sets 4 hours time limit after CV mode charging for balancing battery, if the battery is still unbalanced after 4 hours' balance charging, please reinsert and recharge them to achieve complete balance. |
| |
Balancing inpidual cells battery discharging |
During the process of discharging, the B610Twins can monitor and balance each cell of the battery inpidually. An error message will be indicated and the process will be ended automatically if the voltage of any single one cell is abnormal. |
"Fast" and "storage" mode of lithium battery |
There are various methods of charging Lithium batteries. "Fast" charge reduces the charging time whereas "store charge" can control the final voltage of your battery. This method is best for long term storage and protects the useful life of the battery. |
Automatic charging current limit& Temperature threshold |
You can set the upper limit of the charge current when charging your NiCd or NiMH batteries. It is useful for NiMH batteries of low impedance and capacity in the 'AUTO' charging mode. The batteries internal chemical reaction can cause the temperature of the battery to rise during charging. If the temperature limit is reached (set by the user), the charging process will be terminated. This function is available by connecting an optional temperature probe, which is not included in with the charger. |
Processing time limit& Data store/load& Cyclic charging/discharging |
The user can set the maximum charging time. If the charging time exceeds the limit, the process will be terminated automatically when you set the maximum time for the charging mode. The "Duo" can store data from ten different batteries. The user can set the charging / discharging parameters for a particular battery type and "call up" these settings to charge a battery without additional programming needed. Batteries can be set to charge/ discharge for 5 cycles if needed. |
Adaptable to various types of lithium battery |
| Imax B610 Twins Duo is adaptable to various types of Lithium batteries, such as Li-ion, LiPo and the new LiFe series of batteries. | Delta-peak sensitivity: The automatic charge termination program based on the principle of the Delta-peak voltage detection. When the battery's voltage exceeds the threshold, the process will be terminated automatically. |  |  |
|
Simple Guidelines on Chargers |
Showing the benefits and limitations of different charge methods. 
|
