成  分       Composition

环氧树脂：Epoxy resin

外  观         Appearance

红色糊状：Paste/red-colored

比  重       Specific gravity

1.25

粘  度     Viscosity at 25℃,5rpm

BY320为320mpa·cps.BY350为350mpa·cps

摇变性指数       Thixotropy index

6.9(1rpm/10rpm)

接着强度Adhesive Strength 2125C

Mini-moid tr

                 SOP·IC16p

44N(4.5kgf)0.2mgr twin

45N(4.6kgf)0.3mgr twin

92N(9.4kgf)0.8mgf single×2

电气特性       Electric Property

体积阻抗系数   Volume resistance

绝缘值         Insulation resistance

初期值         Initial value

处理后*         After treating

介电常数       Dielectric constant

节电正常     Dielectric loss tangent

3.6×1016Ω·cm   JIS K6911

1.2×1014Ω        JIS Z3197

1.2×1012Ω

3.12/1MHZ       JIS K6911

0.012/1MHZ       JIS K6911

保存条件     Preservation condition

0℃~10℃的冰箱保存（最佳5±3℃）

To be strictly kept at than

0℃~10℃in refrigerator（5±3℃）

包装方式

Package stBYes

容量

Contents

包装单位

Pack.Unit

点胶机设备厂商

Applicable Dispenser Makers

1.条装Tube

200gr

10Pcs

2.圆柱筒

300ml

5Pcs

For our filling machines only

3.圆柱筒

350gr

12Pcs

4.罐装

PLASTIC JAR

350gr

12Pcs

5.罐装

PLASTIC JAR

1000gr

6Pcs

For screen printing

1.Much lower temperature curing is aimed ay amd is

   practically possible.

2.Very good stable curing shapes without stringing

   and slumping are achieved at super high speed

   dispensing ang very amall dots.

3.Stable adhesive strength can be obtained with a

   variety of SMD.

4.Long-term preservation stability is expected.

5.High heat-resistivity and excellent electric properties are possessed.

6.Usable for screen printing.

1.允许低温度硬化

2.尽管超高速涂敷、微少量涂敷仍可

  保持没有拉丝，塌陷的稳定形状。

3.对于各种表面粘着零件，可获得安

  定的接着强度。

4.储存安定性优良

5.具有高度耐热性和优良的电气

特性。

6.可用于网板印刷。

○Recommended curing condition:Over 120 sec after PCB ’s surface temperature has reached 150℃.or over 150 sec after PCB’s surface temperature has reached 120℃.

○When the higher curing temperature and the longer curing time,the stronger adhesive strength can obtained.We would suggest you to search out an optimum curing condition,for the temperature exerterd on the adhesive may occasionally vary according to the size,material,etc.of component parts mounted on PCBs.

固化条件

○建议固化条件是PCB板表面温度到达150℃后120秒以上，或者是达到120℃后150秒以上。

○固化温度越高，且固化时间越长，可获得更高的粘接强度，依PCB板上装着元件材质、大小不同而实际附加于接着剂的温度会有所不同，因此请依据实际生产情况找出最适合的固化条件。

○Adhesive should be preserved in refrigerator(below

   5±3℃)to keep on its quality.

○Before processing,the adhesive should be taken out

   from the refrigerator for de-freezing about a few

   houre until it reaching the room temperature.

○The bottom of printing screen should be clesned

   timely for good printing shape.

○Toluene or ethBY acetate is possible to use for

   cleaning up this adhesive.

使用方法

○为使接着剂的特性发挥最大效果，请务必放置与冰箱（5±3℃）保存。

○使用前请务必提前几小时从冰箱取出，待红胶恢复至室温后使用。

○为获得良好印刷成形，请及时清洁钢网底部。

○对红胶的洗涤可使用甲苯

○Warranty:6Months.

○Store adhesive in a refrigerator keeping the

   temperature at 5±3℃

○This product may cause skin irritation to sensitive  

   Personnel.

○In case Seal-glo YY-L978 gets in touch with skin,

wash it thoroughly with soap and water.

○In case of eye contact,wash out with clean water

   and consult a medical doctor immediately.

○保质期：6个月。

○请务必将本品保存在5±3℃的冰箱内。

○如果有过敏体质的人，直接接触皮肤有时会引起皮肤过敏，因此请注意。

○误沾皮肤时，请立即用肥皂水清洗。

○进入眼睛时，请尽速以清水冲洗干净，立即接受医生的诊察。