防火DC插座/防火DC电源插座/防火DC充电座
东莞市德凌塑胶电子有限公司
东莞市桥头镇田新工业区
产品属性
图文详情
品牌推荐
品牌/型号
deling/DC-005
品牌
deling
加工定制
是
额定电流
1A（A）A
型号
DC-005
环境温度
-25℃~+70℃（℃）℃
额定电压
12V（V）V
导电体材质
-
壳体材质
塑料
产品认证
RoHS
'1.0构造Tectonic
A型状、尺寸依照制品图而规定. Shape, size in accordance with the provisions of map products.
B外观:各部位应良好无秤锈、裂痕、电镀不良现象.
Appearance : the good parts should weigh no rust, cracks, electroplating ill.
2.0 使用环境条件The use of environmental conditions
A环境湿度Humidity: -25℃~+70℃
B 相对湿度Relative humidity: ≤93% (+40℃)
C 机械性能Mechanical properties
D 动作力Power moves:3~25N
E 端子强度Terminal Strength
各端子在各方面承受500克力作用下,在10秒内,无脱落、破损等不良现象,但弯曲也可.
The terminals in all aspects under 500 Caledon role, in 10 seconds, without any loss, damage and other negative phenomena, but also bending.
3.0 电气性能Electrical Performance
A 额定电流Current ratings:DC 12V 1A.
B 接触电阻Contact resistance:50mΩ以下.
C 绝缘电阻Insulation Resistance:
在端子之间各端子与壳之间加AC 500V 条件下,持续1分钟测试.100MΩ以上. The terminal between the terminal and Shell in between 500V AC conditions, sustained a minute test MΩ above .100.
D 抵抗电压Resistance voltage:
在端子之间端子与壳之间加 AC 500V 60Hz 条件下,持续1分钟测量.无击穿现象出现. In between the terminal and the terminal shell in between AC 500V 60Hz conditions, sustained a minute measurement. No breakdown phenomenon.
4.0可靠性试验Reliability Test
A 寿命试验Life Test
以涂有薄层润滑脂的插头(涂润滑脂防止摩擦过热)以每分钟15~20次,无负载插座拨出5,000次，符合规格3.0和4.0规定值. Coated with a thin layer of grease plugs (TU Grease prevent friction overheated) per minute to 15 ~ 20, a no-load socket allocated 5,000, with the specifications 3.0 and 4.0 provides value
B 温度试验Temperature Test
将插座放置于40±2℃,相对温度90%~95%环境中,96个小时后取出,取去水滴,将插座放置于常温常湿环境中,于30分钟内测试,符合规格3.0和4.0要求. Socket to be placed on the 40 ± 2℃, relative humidity of 90% ~ 95% of the environment, 96 hours after the removal, taking a drop of water, will be placed in the socket temperature often wet environment, in the test within 30 minutes, with 3.0 and 4.0 specifications required.
C 耐热试验Heat test
将插座放置于70±2℃环境下,96个小时后取出,将插座放置于常温常湿环境中,于30分钟内测定,符合规格3.0和4.0要求. Socket to be placed on the 70 ± 2℃ environment, 96 hours after the removal of sockets placed on the temperature and moisture environment, within 30 minutes measured with 3.0 and 4.0 specifications required.
D 耐寒试验Hardy trial
将插座放置于-40±3℃环境中,96个小时后取出,取去水滴,将插座放置于常温湿环境中.于30分钟内测定,符合规格3.0和4.0要求.
Socket to be placed on the 40 ± 3℃ environment, 96 hours after the removal, taking a drop of water, will be placed in the socket regular temperature and humidity environment. Within 30 minutes measured with 3.0 and 4.0 specifications required.
5.0 耐焊接热试验Thermal resistance welding test
A 自动焊;温度 235±5℃,时间5±1秒. Automatic Welding; Temperature of 235 ℃ ± 5, ± a time five seconds.
B 人动焊;温度 350±10℃,时间3±0.5秒. People to welding; The temperature of 350 ± 10 ℃ for 3 ± 0.5 seconds.
'
A型状、尺寸依照制品图而规定. Shape, size in accordance with the provisions of map products.
B外观:各部位应良好无秤锈、裂痕、电镀不良现象.
Appearance : the good parts should weigh no rust, cracks, electroplating ill.
2.0 使用环境条件The use of environmental conditions
A环境湿度Humidity: -25℃~+70℃
B 相对湿度Relative humidity: ≤93% (+40℃)
C 机械性能Mechanical properties
D 动作力Power moves:3~25N
E 端子强度Terminal Strength
各端子在各方面承受500克力作用下,在10秒内,无脱落、破损等不良现象,但弯曲也可.
The terminals in all aspects under 500 Caledon role, in 10 seconds, without any loss, damage and other negative phenomena, but also bending.
3.0 电气性能Electrical Performance
A 额定电流Current ratings:DC 12V 1A.
B 接触电阻Contact resistance:50mΩ以下.
C 绝缘电阻Insulation Resistance:
在端子之间各端子与壳之间加AC 500V 条件下,持续1分钟测试.100MΩ以上. The terminal between the terminal and Shell in between 500V AC conditions, sustained a minute test MΩ above .100.
D 抵抗电压Resistance voltage:
在端子之间端子与壳之间加 AC 500V 60Hz 条件下,持续1分钟测量.无击穿现象出现. In between the terminal and the terminal shell in between AC 500V 60Hz conditions, sustained a minute measurement. No breakdown phenomenon.
4.0可靠性试验Reliability Test
A 寿命试验Life Test
以涂有薄层润滑脂的插头(涂润滑脂防止摩擦过热)以每分钟15~20次,无负载插座拨出5,000次，符合规格3.0和4.0规定值. Coated with a thin layer of grease plugs (TU Grease prevent friction overheated) per minute to 15 ~ 20, a no-load socket allocated 5,000, with the specifications 3.0 and 4.0 provides value
B 温度试验Temperature Test
将插座放置于40±2℃,相对温度90%~95%环境中,96个小时后取出,取去水滴,将插座放置于常温常湿环境中,于30分钟内测试,符合规格3.0和4.0要求. Socket to be placed on the 40 ± 2℃, relative humidity of 90% ~ 95% of the environment, 96 hours after the removal, taking a drop of water, will be placed in the socket temperature often wet environment, in the test within 30 minutes, with 3.0 and 4.0 specifications required.
C 耐热试验Heat test
将插座放置于70±2℃环境下,96个小时后取出,将插座放置于常温常湿环境中,于30分钟内测定,符合规格3.0和4.0要求. Socket to be placed on the 70 ± 2℃ environment, 96 hours after the removal of sockets placed on the temperature and moisture environment, within 30 minutes measured with 3.0 and 4.0 specifications required.
D 耐寒试验Hardy trial
将插座放置于-40±3℃环境中,96个小时后取出,取去水滴,将插座放置于常温湿环境中.于30分钟内测定,符合规格3.0和4.0要求.
Socket to be placed on the 40 ± 3℃ environment, 96 hours after the removal, taking a drop of water, will be placed in the socket regular temperature and humidity environment. Within 30 minutes measured with 3.0 and 4.0 specifications required.
5.0 耐焊接热试验Thermal resistance welding test
A 自动焊;温度 235±5℃,时间5±1秒. Automatic Welding; Temperature of 235 ℃ ± 5, ± a time five seconds.
B 人动焊;温度 350±10℃,时间3±0.5秒. People to welding; The temperature of 350 ± 10 ℃ for 3 ± 0.5 seconds.
'
