Specifications | |||||
Input | |||||
Input Voltage | 90-264 VAC (120-370 VDC) | ||||
Input Frequency | 47-63 Hz | ||||
Input Current | 120 W: 1.7 /1.0 A max at 115 /230 VAC 150 W: 2.0 /0.8 A max at 115 /230 VAC 180 W: 2.7 A max at 90 VAC | ||||
Inrush Current | 120 W: 20 /51 A max at 115 /230 VAC 150 W: 54 /63 A max at 115 /230 VAC 180 W: 54 /108 A max at 115 /230 VAC | ||||
Power Factor | >0.9 | ||||
Earth Leakage Current | 120 W: 0.30 /0.75 mA at 115 /230 VAC 150 W: 0.40 /0.75 mA at 115 /230 VAC 150 W (-M): 0.075 mA at 230 VAC 180 W: 0.75 mA at 230 VAC | ||||
Input Protection | Internal T3.15 A /250 VAC fuse in line, SDS150-M: line and neutral | ||||
No Load Input Power | 180 W: ≤ 0.5 W | ||||
Output | |||||
Output Voltage | See datasheet | ||||
Output Voltage Trim | ±5% output 1 only (3.3 V variant ±10%) SDS180: not user adjustable | ||||
Initial Set Accuracy | Single output models: ±1% Multi-output models: ±5% | ||||
Minimum Load | No minimum load required for single output models. For multi-output models see table on datasheet. | ||||
Start Up Delay | 2 s max | ||||
Start Up Rise Time | 2 ms typical | ||||
Hold Up Time | 16 ms minimum at full load and 110 VAC | ||||
Line Regulation | 0.5% typical | ||||
Load Regulation | 3.0% typical | ||||
Transient Response | 4% max deviation, recovery to within 1% in 500 μs for a 50% load change | ||||
Ripple & Noise | 1% pk-pk typical, 20 MHz bandwidth | ||||
Overvoltage Protection | 112-132% V1 only, recycle input to reset | ||||
Overload Protection | All outputs: 110-150% with auto recovery (primary power limit) | ||||
Short Circuit Protection | Trip & restart (Hiccup mode), auto recovery | ||||
Temperature Coefficient | ±0.04%/°C | ||||
General | |||||
Efficiency | 120 W: 80% typical 150 W and 180 W: 88% typical | ||||
Isolation | 3000 VAC Input to Output, 1500 VAC Input to Ground, 500 VDC Output to Ground, SDS150-M: 5600 VDC Input to Output, 2800 VDC Input to Ground, 500 VDC Output to Ground | ||||
Switching Frequency | 120 W: PFC 100 kHz typical, PWM 67 kHz typical. 150 W: PFC 34 kHz minimum, PWM 55 kHz typical. 180 W: PFC 67 kHz typical, PWM 67 kHz typical | ||||
Power Density | 120 W: 4.87 W/In3, 150 W: 6.50 W/In3 180 W: 7.47 W/In3 | ||||
Signals | Power Fail Detect = TTL active low, combined AC and DC OK signal (-P versions SDS120 & 150 only) Warning time 16 ms | ||||
MTBF | >130 kHrs to MIL-HDBK-217F at 25 °C, GB | ||||
Isolation Resistance | 50 MΩ | ||||
Environmental | |||||
Operating Temperature | 0 °C to +70 °C (-20 °C to +70 °C, SDS180), derate linearly from 100% load at +50 °C to 50% load at +70 °C, for low temperature option add suffix -L: -40 °C to +70 °C, SDS120 and SDS150, not available for SDS150-M and SDS180 | ||||
Cooling | Convection-cooled | ||||
Operating Humidity | 5-95% RH, non-condensing | ||||
Storage Temperature | -40 °C to +85 °C | ||||
EMC and Safety | |||||
Emissions | EN55022, level B conducted & radiated. SDS150-M: EN55011 class B conducted & radiated | ||||
Harmonic Currents | EN61000-3-2 class A | ||||
Voltage Flicker | EN61000-3-3 | ||||
ESD Immunity | EN61000-4-2, level 2 contact, Perf Criteria A SDS150: level 3 air, Perf criteria A SDS150-M: level 3 contact, Perf Criteria A | ||||
Radiated Immunity | EN61000-4-3, level 2, Perf Criteria A SDS150-M: level 3, Perf Criteria A | ||||
EFT/Burst | EN61000-4-4, level 2 Perf Criteria A | ||||
Surge | EN61000-4-5, installation class 3, Perf Criteria A | ||||
Conducted Immunity | EN61000-4-6, level 2 , Perf Criteria A SDS150-M: level 3, Perf Criteria A | ||||
Dips & Interruptions | EN61000-4-11, 30% 10 ms, 60% 100 ms, >95% 5000 ms Perf Criteria A, B, B | ||||
Safety Approvals | EN60950-1, UL60950-1,CSA60950-1 per cUL. SDS150-M: EN60601-1 | ||||
Magnetic Field | EN61000-4-8, 1 A/m, Perf Criteria A SDS150-M: 3 A/m, Perf Criteria A |
Model Number | Input | Output | Power | Back to top | |
SDS120 COVER | Stock Check | ||||
SDS120PS03B | 90-260 VAC | 3.3 V/22.0 A | 72 W | Stock Check | |
SDS120PD00B | 90-260 VAC | o/p 1: 3.3 V/15.0 A, o/p 2: 5.0 V/6.0 A | 79.5 W | ||
SDS120PT00B | 90-260 VAC | o/p 1: 3.3 V/15.0 A, o/p 2: 5.0 V/6.0 A, o/p 3: 12.0 V/1.0 A | 91.5 W | Stock Check | |
SDS120PT01B | 90-260 VAC | o/p 1: 3.3 V/15.0 A, o/p 2: 5.0 V/6.0 A, o/p 3: -12.0 V/1.0 A | 91.5 W | ||
SDS120PS05B | 90-260 VAC | 5.0 V/22.0 A | 110 W | Stock Check | |
SDS120PS07B | 90-260 VAC | 7.0 V/16.42 A | 115 W | ||
SDS120PD01B | 90-260 VAC | o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A | 120 W | ||
SDS120PD02B | 90-260 VAC | o/p 1: 5.0 V/15.0 A, o/p 2: 12.0 V/6.0 A | 120 W | ||
SDS120PD03B | 90-260 VAC | o/p 1: 5.0 V/15.0 A, o/p 2: 15.0 V/6.0 A | 120 W | ||
SDS120PD04B | 90-260 VAC | o/p 1: 5.0 V/15.0 A, o/p 2: 24.0 V/3.5 A | 120 W | ||
SDS120PD05B | 90-260 VAC | o/p 1: 5.0 V/15.0 A, o/p 2: -24.0 V/2.0 A | 120 W | ||
SDS120PD06B | 90-260 VAC | o/p 1: 28.0 V/3.92 A, o/p 2: 5.0 V/2.0 A | 120 W | ||
SDS120PS09B | 90-260 VAC | 9.0 V/13.33 A | 120 W | ||
SDS120PS12B | 90-260 VAC | 12.0 V/10.0 A | 120 W | Stock Check | |
SDS120PS15B | 90-260 VAC | 15.0 V/8.0 A | 120 W | Stock Check | |
SDS120PS18B | 90-260 VAC | 18.0 V/6.66 A | 120 W | ||
SDS120PS24B | 90-260 VAC | 24.0 V/5.0 A | 120 W | Stock Check | |
SDS120PS28B | 90-260 VAC | 28.0 V/4.28 A | 120 W | Stock Check | |
SDS120PS36B | 90-260 VAC | 36.0 V/3.33 A | 120 W | ||
SDS120PS48B | 90-260 VAC | 48.0 V/2.5 A | 120 W | Stock Check | |
SDS120PT02B | 90-260 VAC | o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: 5.0 V/0.8 A | 120 W | ||
SDS120PT03B | 90-260 VAC | o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: -5.0 V/0.8 A | 120 W | ||
SDS120PT04B | 90-260 VAC | o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: -12.0 V/0.8 A | 120 W | ||
SDS120PT05B | 90-260 VAC | o/p 1: 3.3 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: 12.0 V/0.8 A | 120 W | ||
SDS120PT06B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: 5.0 V/0.8 A | 120 W | ||
SDS120PT07B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: -5.0 V/0.8 A | 120 W | Stock Check | |
SDS120PT08B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: -12.0 V/0.8 A | 120 W | Stock Check | |
SDS120PT09B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 12.0 V/6.0 A, o/p 3: 12.0 V/0.8 A | 120 W | ||
SDS120PT10B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 15.0 V/6.0 A, o/p 3: -15.0 V/0.8 A | 120 W | Stock Check | |
SDS120PT11B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 15.0 V/6.0 A, o/p 3: 15.0 V/0.8 A | 120 W | ||
SDS120PT12B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 24.0 V/3.5 A, o/p 3: -24.0 V/0.8 A | 120 W | ||
SDS120PT13B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 24.0 V/3.5 A, o/p 3: 24.0 V/0.8 A | 120 W | ||
SDS120PT14B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 24.0 V/3.5 A, o/p 3: -12.0 V/0.8 A | 120 W | ||
SDS120PT15B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 24.0 V/3.5 A, o/p 3: 12.0 V/0.8 A | 120 W | Stock Check | |
SDS120PT16B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 10.0 V/6.0 A, o/p 3: -10.0 V/1.0 A | 120 W | ||
SDS120PT17B | 90-260 VAC | o/p 1: 5 V/15.0 A, o/p 2: 10.0 V/6.0 A, o/p 3: 10.0 V/1.0 A | 120 W | ||
SDS150PS09B | 90-260 VAC | 9.0 V/16.0 A | 144 W | Stock Check | |
SDS150PS12B | 90-260 VAC | 12.0 V/12.5 A | 150 W | Stock Check | |
SDS150PS12B-M | 90-260 VAC | 12.0 V/12.5 A | 150 W | Stock Check | |
SDS150PS15B | 90-260 VAC | 15.0 V/10.0 A | 150 W | Stock Check | |
SDS150PS18B | 90-260 VAC | 18.0 V/8.33 A | 150 W | Stock Check | |
SDS150PS24B | 90-260 VAC | 24.0 V/6.25 A | 150 W | Stock Check | |
SDS150PS24B-M | 90-260 VAC | 24.0 V/6.25 A | 150 W | Stock Check | |
SDS150PS30B | 90-260 VAC | 30.0 V/5.0 A | 150 W | ||
SDS150PS36B | 90-260 VAC | 36.0 V/4.17 A | 150 W | ||
SDS150PS48B | 90-260 VAC | 48.0 V/3.13 A | 150 W | Stock Check | |
SDS180PS12B | 90-260 VAC | 12.0 V/14.58 A | 180 W | Stock Check | |
SDS180PS24B | 90-260 VAC | 24.0 V/7.5 A | 180 W | Stock Check | |
SDS180PS48B | 90-260 VAC | 48.0 V/3.75 A | 180 W | Stock Check | |