1、本产品采用高级进口丙烯酸树脂和高级颜料经过细制研磨加工组合而成，适用范围：各种金属、玻璃、陶瓷、石材、电镀(含水电镀)、阳极氧化铝表面、静电喷漆面及烤漆面等制品的丝印及移印，不需加固化剂，不需烘烤，即可获得优异的附着力。
2、产品特性：平光、附着力佳、流平性佳、硬度强、耐酒精、耐冲压、抗刮伤、耐化学品。 3、稀释剂：建议采用本公司配套专用稀释剂开油。 4、固化剂：本产品无需加固化剂，切勿加不配套的固化剂，会影响其效果 5、油墨调配方法：搅拌时先加稀释剂10%左右稀释到印刷适合粘度。 6、干燥时间：表干时间自然挥发5-10分钟，实干时间在24小时以内，48小时后达最佳性能，烤箱80℃烘烤30分钟性能更优。 7、使用期限：半年，过期请弃用，加了其他助剂剩余油墨不可回收。 【油墨使用注意事项】 1、试印确认符合要求后再批量生产。 2、做好被印物的表面清除油脂及杂质工作，以促进附着效果。 3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、耐磨性等性能的检测，需要完全固化后方可检测。 4、未经允许情况下，不得将本系列油墨与其它类型油墨混用及配色。 5、丝网印刷加适量拉丝膏用本公司特慢干稀释剂更适宜印刷工艺顺畅。 6、注意作业车间的湿度，湿度过大会影响附着力，温度高容易堵网。 【油墨性能检测结果】 1、3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。 2、纯度99%的酒精500G力在油墨表面来回擦拭100次无脱色。 【油墨使用安全规则】 1、油墨，稀释剂使用及储存时严禁烟火 2、使用时注意施工场所的通风状况良好。 3、尽量避免皮肤直接接触。 4、本品不慎溅入口、鼻、眼、耳内，应用大量水清洗或直接求助医生。 5、对本品过敏者，使用前应涂覆一层皮肤扶肤膏或戴不渗透手套。 6、注意作业车间的湿度，湿度过大会影响附着力，温度高容易堵网。
1, and this products used senior imports acrylic resin and senior pigment after fine system grinding processing combination and into, applies range: various metal, and glass, and ceramic, and stone, and plating (containing water plating), and anode alumina surface, and electrostatic painting surface and the roast paint surface, products of silk printed and the moved printed, not needed reinforcement of agent, not needed baking, can obtained excellent of adhesion. 2, product characteristics: flat, good adhesion, excellent levelling, hardness, resistance to alcohol, punching, scratch-resistant, resistant to chemicals. 3, thinner: oil companies supporting special thinner is recommended to open. 4, curing agent: this product without reinforcing agent, do not add not supporting the curing agent, will effect the its deployment method 5, ink: before mixing and diluting agent diluted to around 10% printing suitable viscosity. 6, drying time: table dry time volatile nature 5-10 minutes, action time in less than 24 hours, 48 hours after the best performance and better oven 80 ° c and bake for 30 minutes. 7, the use of the term: for half a year, expired deprecated, other additives have been added the remaining ink cannot be recycled. "Ink notes on use" 1, try printing to comply with the requirements, and then mass production. 2, by print work surface clear of grease and impurities, in order to promote adhesion effect. 3, adhesion, hardness, acid resistance, ethanol resistance, chemical resistance, scratch resistance and wear resistance properties of the test, you need to test when it is fully cured. 4, cases without permission, ink in this series must not be mixed with other types of inks and color schemes. 5, adds the right amount of wire drawing paste screen printing companies for slow thinner more suitable printing process smoother. 6, notices, job shop, humidity and humidity affect the adhesion of the General Assembly, high temperature easier blocking network. "Ink test results" 1, 3M adhesive tape stuck to the paint surface where many of the ink pulling up a 45-degree angle quickly without oil. 2, 99% pure alcohol 500G in ink surface wipe back and forth 100 times without bleaching. "Ink used security rules" 1, ink, thinner when the use and storage of fire 2, when construction of the ventilation of the premises in good condition. 3, try to avoid direct skin contact. 4, this product is accidentally spilled the entrance, in the nose, eyes, ears, a large amount of water to clean or doctor directly for help. 5, allergic to the chemicals, should be coated with a layer of skin before using helped skin cream or impervious gloves. 6, notices, job shop, humidity and humidity affect the adhesion of the General Assembly, high temperature easier blocking network
