【Flyin 100G 40 channel Thermal AWG specification】价格_厂家

Flyin 100G 40 channel Thermal AWG specification

不限

￥10

中国深圳

产品属性

图文详情

品牌推荐

品牌

flyin

型号

Flyin 100G 40 channel Thermal AWG specification

类型

密集波分复用DWDM

速度

高速

通道

多通道

输出波长

C-Bandnm

线宽

0.0002mm

加工定制

是

1. 产品概述/Product Overview

This document presents the generic specification for the 40-channel 100GHz AWG MUX/DEMUX component supplied for use in DWDM system.

This component is designed for use within the C -band release of DWDM system. To decrease the power dissipation of the devices in different environmental conditions, the AWG package is special designed with selection of reliable thermal plastic with low thermal conduction, and the AWG operating temperature is controlled by using foil resist heater or Peltier TEC with thermistor temperature sensor. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications.

Flyin’s label is only for spec review and can be no label or customer label on the device on delivered samples and products

2. 极限条件/Absolute Maximum Ratings (unless otherwise specified)

参数/Parameters	条件/Conditions	规格/Specifications		单位/Units
		最小/Min.	最大/Max.	单位/Units
工作温度/Operating Temperature	产品正常工作时/Operating	-5	65	oC
工作湿度/Operating Humidity	产品正常工作时/Operating	5	95	%RH
存储温度/Storage Temperature	产品不工作时/Non_Operating	-40	+85	oC
存储湿度/Storage Humidity	产品不工作时/Non_Operating	5	95	%RH

3.      光性能/Optical Specification (平顶AWG/ Flattop Thermal AWG)
参数/Parameters
条件/Condition
规格/Specs
单位/Units
Min
Typ
Max
通道数/Number of Channels

40

通道间距/Number Channel Spacing
100GHz
100
GHz
中心波长/Cha. Center Wavelength
ITU频率/ITU frequency.
C -band
nm
通带频率/Clear Channel Passband

±0.1
nm
波长精度/Wavelength Stability
Maximum range of the wavelength error of all channels and temperatures in average polarization.
±0.05
nm
-1 dB 带宽/-1 dB Channel Bandwidth
Clear channel bandwidth defined by passband shape. For each channel
0.4

nm
-3 dB 带宽/-3 dB Channel Bandwidth
Clear channel bandwidth defined by passband shape. For each channel
0.6

nm
插损/Optical Insertion Loss at ITU grid
Defined as the minimum transmission at ITU wavelength for all channels. For each channel, at all temperatures and polarizations.

4.5
6.0
dB
相邻通道隔离度/Adjacent Channel Isolation
Insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of the adjacent channels.
25

dB
非相邻通道隔离度/Non-Adjacent, Channel Isolation
Insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of the nonadjacent channels.
30

dB
总隔离度/Total Channel Isolation
Total cumulative insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of all other channels, including adjacent channels.
22

dB
插损一致性/Insertion Loss Uniformity
Maximum range of the insertion loss variation within ITU across all channels, polarizations and temperatures.

1.0
1.5
dB
方向性Directivity(Mux Only)
Ratio of reflected power out of any channel(other than channel n)to power in from the input channel n
40

dB
插损平坦度/Insertion Loss Ripple
Any maxima and any minima of optical loss across ITU band, excluding boundary points, for each channel at each port

0.5
dB
回损/Optical Return loss
Input & output ports
40

dB
PDL/Polarization Dependent Loss in Clear Channel Band
Worst-case value measured in ITU band

0.3
0.5
dB
偏振模式色散/Polarization Mode Dispersion

0.5
ps
最大承受光功率/Maximum Optical Power

23
dBm
功率监控范围/MUX/DEMUX input/ output
Monitoring range

-35

+23
dBm
1.       IL Represents the worst case over a +/-0.1nm window around the ITU wavelength.
2.       PDL was measured on average polarization over a +/- 0.1nm window around the ITU wavelength.

4.      机械尺寸/Mechanical Schematic and Dimensions
尺寸/Dimensions
150 x 65 x 16 (mm)
安装孔/ Space between space between screws
140×58 (mm)
光纤类型/Fiber Type
公共端Common SMF-28e fiber with 900um loose tube，，通道端Channels G652D ribbons
光纤编排/Fiber Format
4x 12带纤/4x 12-fiber ribbons
输入光纤长度/ Input fiber length
500mm ±50mmwith 900um loose tube
输出光纤长度Output fiber length
Ribbon200mm±20 mmand Fan out 300mm±30mmwith 900um loose tube
光纤标识/fiber Identification
光纤末端贴数码贴标识/
Label with channel number to be placed midway between fiber end-points
连接器类型/Connector Options
Common
LC/UPC
Channels
LC/UPC
带纤光纤标识/Fiber

1
蓝/Blue
2
橙/Orange
3
绿/Green
4
褐/Brown
5
灰/Grey
6
白/White
7
红/Red
8
黑/Black
9
黄/Yellow
10
紫/Purple
11
粉/Pink
12
水/Aqua

Fan-out

Fan-out
*可以按客户要求使用其他结构/Also available in other configuration

AWG Module

LC/UPC
Fiber Coding

LC/UPC

5.      电子规格/Electrical Specifications
Only for the thermal AWG module which has an internal temperature control circuit.
NO.
Parameters
Notes
Specifications
Units
Min
Typ
Max
2.23
Set-Point temperature of
component
Optimum operating temperature section for thermal AWG
The commands could only set current temperature and threshold in this range.
65

90
°C
2.24
Set-Point temperature stability
Over entire operating temperature range for thermal AWG

±0.5
°C
2.25
Heater Drive Voltage

+5

V
2.26
Heater Drive Current

2.5
A
2.27
Heater Power Dissipation
(maximum, stable)

12.5
W
2.28
Heater Power Dissipation
(stable state)
25°C ambient temperature

6
W
2.29
AWG Temperature Settling
Time
AWG warm up time from a cold start(25°Cambient temperature) to set point for thermal AWG

7
min
2.30
AWG Temperature Settling
Time
AWG warm up time from a cold start(-5°Cambient temperature) to set point for thermal AWG

15
min
Temperature control IC build inside

6.      电接口/Electric interface
Connector type: 10 pin FRC box type (2.54mmpitch) male connector.
Pin definition is as below:
NO.
pin#
Signal Name
Type
Direction
Descriptions
2.31
1
+5V
Power
----
supply for Heater circuit
2.32
2
+5V
Power
----
supply for Heater circuit
2.33
3
+5V
Power
----
supply for control circuit
2.34
4
Ready
TTL
Output
※         Set HIGH when the internal temperature is at a set-point temperature.
※         Set LOW when the internal temperature is not at a set-point temperature (higher than the Upper Temperature Threshold or lower than the Under Temperature Threshold).
※         This signal should be 3.3V TTL level.
2.35
5
Alarm
TTL
Output
※         Set HIGH when the internal temperature is higher than the set-point temperature.
※         Set LOW when the internal temperature is not higher than the set-point temperature.
Pin4 and pin5 could be used to check the temperature’s status.
※         This signal should be 3.3V TTL level.
2.36
6
Enable
TTL
Input
※         If set HIGH, the heater circuit is activated.
※         If set LOW, the heater circuit is disabled.
※         This signal should be 3.3V TTL level.
2.37
7*
TX
TTL
Output
RS232 transmit signal
This signal should be 3.3V TTL level.
2.38
8
GND
Power
----
Ground
2.39
9*
Rx
TTL
Input
RS232 receive signal
This signal should be 3.3V TTL level.
2.40
10
GND
Power
----
Ground
*: Information available for inquiry includes Chip Temperature, Module Status, P/N & SN.

7.      可靠性说明/Reliability Specifications
The planar DWDM components described within this datasheet are fully qualified according to Telcordia reliability assurance requirements for fiber optic and opto-electronic components (GR-1221-CORE/UNC, Generic Reliability Assurance Requirements for Fiber Optic Branching Components, and Telcordia TR-NWT-000468, Reliability Assurance Practices for Opto-electronic Devices). The reliability report is available for request.

8.      订购信息/Ordering Part Code Sequence
AWG
X
XX
X
XXX
X
X
X
XX

Band
Number of Channels
Spacing
1st Channel
Filter Shape
Package
Fiber Length
In/Out Connector
C=C-Band
L=L-Band
D=C+L-Band
X=Customize
16=16-CH
32=32-CH
40=40-CH
48=48-CH
XX=Special
1=100G
2=200G
5=50G
X=Special
C60=C60
H59=H59
C59=C59
H58=H58
XXX=special
G=Gaussian
B=Broad Gaussiar
F=Flat Top
M=Module
R=Rack
X=Special
1=0.5m
2=1m
3=1.5m
4=2m
5=2.5m
6=3m
S=Specify
0=None
1=FC/APC
2=FC/PC
3=SC/APC
4=SC/PC
5=LC/APC
6=LC/PC
7=ST/UPC
S=Specify

电子元器件 > 光电器件 > 光纤波分复用器 >

参数/Parameters	条件/Condition	规格/Specs					单位/Units
		Min	Typ		Max
通道数/Number of Channels		40
通道间距/Number Channel Spacing	100GHz	100					GHz
中心波长/Cha. Center Wavelength	ITU频率/ITU frequency.	C -band					nm
通带频率/Clear Channel Passband		±0.1					nm
波长精度/Wavelength Stability	Maximum range of the wavelength error of all channels and temperatures in average polarization.	±0.05					nm
-1 dB 带宽/-1 dB Channel Bandwidth	Clear channel bandwidth defined by passband shape. For each channel	0.4					nm
-3 dB 带宽/-3 dB Channel Bandwidth	Clear channel bandwidth defined by passband shape. For each channel	0.6					nm
插损/Optical Insertion Loss at ITU grid	Defined as the minimum transmission at ITU wavelength for all channels. For each channel, at all temperatures and polarizations.			4.5		6.0	dB
相邻通道隔离度/Adjacent Channel Isolation	Insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of the adjacent channels.	25					dB
非相邻通道隔离度/Non-Adjacent, Channel Isolation	Insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of the nonadjacent channels.	30					dB
总隔离度/Total Channel Isolation	Total cumulative insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of all other channels, including adjacent channels.	22					dB
插损一致性/Insertion Loss Uniformity	Maximum range of the insertion loss variation within ITU across all channels, polarizations and temperatures.			1.0		1.5	dB
方向性Directivity(Mux Only)	Ratio of reflected power out of any channel(other than channel n)to power in from the input channel n	40					dB
插损平坦度/Insertion Loss Ripple	Any maxima and any minima of optical loss across ITU band, excluding boundary points, for each channel at each port					0.5	dB
回损/Optical Return loss	Input & output ports	40					dB
PDL/Polarization Dependent Loss in Clear Channel Band	Worst-case value measured in ITU band			0.3		0.5	dB
偏振模式色散/Polarization Mode Dispersion						0.5	ps
最大承受光功率/Maximum Optical Power						23	dBm
功率监控范围/MUX/DEMUX input/ output Monitoring range		-35				+23	dBm

NO.	Parameters	Notes	Specifications			Units
NO.	Parameters	Notes	Min	Typ	Max	Units
2.23	Set-Point temperature of component	Optimum operating temperature section for thermal AWG The commands could only set current temperature and threshold in this range.	65		90	°C
2.24	Set-Point temperature stability	Over entire operating temperature range for thermal AWG			±0.5	°C
2.25	Heater Drive Voltage			+5		V
2.26	Heater Drive Current				2.5	A
2.27	Heater Power Dissipation (maximum, stable)				12.5	W
2.28	Heater Power Dissipation (stable state)	25°C ambient temperature			6	W
2.29	AWG Temperature Settling Time	AWG warm up time from a cold start(25°Cambient temperature) to set point for thermal AWG			7	min
2.30	AWG Temperature Settling Time	AWG warm up time from a cold start(-5°Cambient temperature) to set point for thermal AWG			15	min

NO.	pin#	Signal Name	Type	Direction	Descriptions
2.31	1	+5V	Power	----	supply for Heater circuit
2.32	2	+5V	Power	----	supply for Heater circuit
2.33	3	+5V	Power	----	supply for control circuit
2.34	4	Ready	TTL	Output	※ Set HIGH when the internal temperature is at a set-point temperature. ※ Set LOW when the internal temperature is not at a set-point temperature (higher than the Upper Temperature Threshold or lower than the Under Temperature Threshold). ※ This signal should be 3.3V TTL level.
2.35	5	Alarm	TTL	Output	※ Set HIGH when the internal temperature is higher than the set-point temperature. ※ Set LOW when the internal temperature is not higher than the set-point temperature. Pin4 and pin5 could be used to check the temperature’s status. ※ This signal should be 3.3V TTL level.
2.36	6	Enable	TTL	Input	※ If set HIGH, the heater circuit is activated. ※ If set LOW, the heater circuit is disabled. ※ This signal should be 3.3V TTL level.
2.37	7*	TX	TTL	Output	RS232 transmit signal This signal should be 3.3V TTL level.
2.38	8	GND	Power	----	Ground
2.39	9*	Rx	TTL	Input	RS232 receive signal This signal should be 3.3V TTL level.
2.40	10	GND	Power	----	Ground