亲看中上面的产品了吗O(∩_∩)O~
如需了解详情可联系我们的客服代表
联系方式
贺小姐：13713377315
阿里旺旺：xingchisewing678
QQ：2355509413
Email：2355509413@qq.com
固话：0769-89161572-219
如需了解详情请联系
贺小姐:13713377315
或加Q:2355509413 谢谢!
品牌：长弘牌
型号：XDB-668
产品名称：手动断布机
§技术参数:
刀片直径:108mm
电压:单相110V/ 60HZ或220~240V/50HZ
刀片转速:18000转/分
输出功率:180W
§Technical parameters:
Side of Blade: 108mm
Shape of the Blade: round
Electric Pressure: single phase 110V/60HZ or 220V-240V/50HZ
Revolving speed of the Knife: 18000 r.p.m
Output: 180w
§检查：
A.调整磨刀砂轮
当砂轮磨不到刀片时,应放松磨刀臂螺钉,调整磨刀砂轮位置,使磨刀砂轮和刀片边缘间有一个适宜的距离,然后锁紧螺钉.
B.更换磨刀砂轮
拧下螺钉,取下磨刀砂轮,然后装上新的磨刀砂轮.
C.更换圆刀片
1.拿下磨削轮部件.
2.旋下刀片锁紧螺母.
3.取下刀片.
4.当安装新刀片时,应使印有"This sede up" 的这一面朝向操作者.
5.装上新刀片后,调整磨削砂轮至适宜位置.
D. 更换底刀
1.旋下底刀固定板螺钉,取下底刀固定板.
2.拧下底刀固定螺钉,换上新底刀,确保底刀侧平面贴近圆刀边缘.
E. 更换碳刷
1.碳刷的磨损会引起电机的故障,当碳刷磨得只剩下5~6mm时,必须更换碳刷.
2.用螺丝刀旋下碳刷螺母,更换碳刷.
3.须同时更换左右碳刷.
4.更换时,接线弹簧须钩住碳刷壳金属部件.
F. 清洁导轨和主机
1.当断布机连续工作10到20小时后,须用刷子清除导轨上遗留下的织物.
2.当断布机的连续工作30天后,须从导轨上拆下主机,用刷子逐一清洁各导轨槽,清洁后,装回主机.
注意:
1.操作前,应检查导轨平面是否干净.
2.为安全起见,应装有接地线.
§Checking：
A. Adjusting the grinder
When the blade is worn out, adjust the grinder position by unscrewing the screw for the grinder arm so as to ensure a correct distance between the grinder and the blade edge. After finishing adjustment, screw up the screw.
B. Replacing the Grinding Wheel
Take off the grinding wheel by unscrewing it off.Mount the new grinding wheel then.
C. Replacing the Knife
1.take off the grinding wheel unit.
2.unscrew the lock nut for the knife.
3.take off the knife.
4.when mounting the knife, make sure that the side printed with "this side up" should be placed facing the operator.
5.After the blade is replaced, adjust the position of the grinder at the proper.
D. Eplacing the Knife Frame
1.To take off the knife frame arm by unscrewing the screw for the knife frame arm.
2.Replacing the knife frame by Unscrewing the fixed screw.Replace the knife frame and ensured the flat surface of the knife frame adjacent to the blade edge.
E.Replace of carbon brush
1.Too much weaving of carbon brush will cause motor trubles.Carbon brush must be replaced when it to 5-6mm.
2.Carbon brush cap is replaced by turning it left by attached wrench.
3.Always replace right and left carbon brushes simultaneously.
4.Be sure to hold metallic part of the brush.
F.Clean the Track and the Master Machine
1.Clean all the wasted cotton and cloth in the track with a brush thoroughly after the machine is continuce running for 10 to 20 hours.
2.To take the master machine of the track and thoroughly clean the L-type track with a brash after the machine is continuously running for 30 days. Repeatedly cleand it as shown in item.To mount the master machinein the track groove again after cleanness is ensured.
Cautions:
1.Beforing operating the machine, make sure of complete cheanness of the track surface.
2.Safety electric ground wire is used for the sake of safety.
§售后服务：
1. 以上报价为人民币现金报价（不含税，不含运费）。
2. 整机保修一年,马达包换一年
运费说明：本公司所有产品默认选择发货运，如客户有特别要求发快递的或者有指定的货运公司请与客服联系，在购买后未说明的，公司默认发货运不得异议！运费到付！
注明：本公司出售的品牌缝纫机均为原厂正品，假一赔十，欢迎广大顾客求证！
发票：本公司可以开具17%增值税发票，属于正规的有限公司，如客户需要开票的请向客服提出，未提出者一律不开票，需开票的根据不同的产品收取相应的税金（详情请咨询客服）。
付款方式：款到发货，报价为不含运费不含税。
§公司简介：
本公司官网：www.dgxingchisewing.com
星驰缝制设备有限公司 专业销售的产品有：高车（341、8B、246、244以及零部件销售）、电脑花样机（2010、2516 、3020、210D 、5030、6030）电脑同步车（0368、0398）、电脑平车（8700/8700D）、人字车（同步人字车，高车人字车，曲臂人字车，四针六线人字车）、同步车（0318、0302、0338、0303以及零部件销售）、修边机、罗拉车、包边车、拉帮机、绷缝机、钉扣机、多针机 、平车、平双针车、埋箱车、锁边机、铲皮机801及配件、长臂车，特种车，沙发类针车批发。
零部件销售有：挑线簧、天平、挑线杆、针杆、五金类、螺丝类、车针类、高车、DY类、梭壳、梭心、特种车配件、平车、DY车配件、电脑车配件、双针车配件、梭床类、平车胶底、341、8B配件、剪刀类、夹线器、牙齿、针板类。
