【加纤PP MF004AI美国液氮/耐烘烤高温/退火收缩率小/耐冲击性】价格_厂家

加纤PP MF004AI美国液氮/耐烘烤高温/退火收缩率小/耐冲击性

1台起批

￥16800.00

东莞市樟木头镇塑胶原料市场一期Z-09A

产品属性

图文详情

品牌推荐

厂家(产地)

美国LNP

牌号

MF004AI

销售方式

品牌经销

类型

标准料

LNP* Thermotuf* Compound MF004AI

|British

|Metric

|PDF

Americas: COMMERCIAL

Also known as:LNP* Thermotuf* Compound MF-1004 HI

Product reorder name:MF004AI

LNP* Thermotuf* MF004AI is a compound based on Polypropylene resin containing Glass Fiber. Added features of this material include: High Impact.

Property

TYPICAL PROPERTIES(1)
MECHANICAL	Value	Unit	Standard
Tensile Stress, break	400	kgf/cm²	ASTM D 638
Tensile Strain, break	4.8	%	ASTM D 638
Tensile Modulus, 50 mm/min	49200	kgf/cm²	ASTM D 638
Flexural Stress	420	kgf/cm²	ASTM D 790
Flexural Modulus	28100	kgf/cm²	ASTM D 790
Tensile Stress, break	37	MPa	ISO 527
Tensile Strain, break	4.5	%	ISO 527
Tensile Modulus, 1 mm/min	4940	MPa	ISO 527
Flexural Stress	46	MPa	ISO 178
Flexural Modulus	3000	MPa	ISO 178
IMPACT	Value	Unit	Standard
Izod Impact, unnotched, 23°C	44	cm-kgf/cm	ASTM D 4812
Izod Impact, notched, 23°C	17	cm-kgf/cm	ASTM D 256
Izod Impact, unnotched 80104 +23°C	28	kJ/m²	ISO 180/1U
Izod Impact, notched 80104 +23°C	14	kJ/m²	ISO 180/1A
THERMAL	Value	Unit	Standard
HDT, 0.45 MPa, 3.2 mm, unannealed	150	°C	ASTM D 648
HDT, 1.82 MPa, 3.2mm, unannealed	108	°C	ASTM D 648
CTE, -40°C to 40°C, flow	1.06E-04	1/°C	ASTM E 831
CTE, -40°C to 40°C, xflow	6.84E-05	1/°C	ASTM E 831
CTE, -40°C to 40°C, flow	1.05E-04	1/°C	ISO 11359-2
CTE, -40°C to 40°C, xflow	6.8E-05	1/°C	ISO 11359-2
HDT/Bf, 0.45 MPa Flatw 80104 sp=64mm	144	°C	ISO 75/Bf
HDT/Af, 1.8 MPa Flatw 80104 sp=64mm	104	°C	ISO 75/Af
PHYSICAL	Value	Unit	Standard
Density	1.03	g/cm³	ASTM D 792
Mold Shrinkage, flow, 24 hrs (5)	1.1 - 1.3	%	ASTM D 955
Mold Shrinkage, xflow, 24 hrs (5)	1.1 - 1.3	%	ASTM D 955
Mold Shrinkage, flow, 24 hrs (5)	1.2	%	ISO 294
Mold Shrinkage, xflow, 24 hrs (5)	1.2	%	ISO 294
Density	1.03	g/cm³	ISO 1183

Source GMD, last updated:2008/09/24

Processing

Parameter
Injection Molding	Value	Unit
Drying Temperature	80	°C
Drying Time	4	hrs
Melt Temperature	225 - 250	°C
Front - Zone 3 Temperature	240 - 250	°C
Middle - Zone 2 Temperature	215 - 225	°C
Rear - Zone 1 Temperature	195 - 205	°C
Mold Temperature	30 - 50	°C
Back Pressure	0.2 - 0.3	MPa
Screw Speed	30 - 60	rpm

Source GMD, last updated:2008/09/24

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.

PLEASECONTACT USFOR AVAILABILITY IN YOUR REGION.

(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.

(2) Only typical data for selection purposes. Not to be used for part or tool design.

(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.

(4) Internal measurements according to UL standards.

(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

Disclaimer :THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER\'S STANDARD CONDITIONS OF SALE, WHICH CAN BE FOUND AThttp://www.sabic-ip.com. AND ARE AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER\'S PRODUCTS, SERVICES OR RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER\'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN.Each user is responsible for making its own determination as to the suitability of Seller\'s products, services or recommendations for the user\'s particular use through appropriate end-use testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller\'s Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible use of any product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of such product, service or design in a manner that infringes any patent or other intellectual property right.
SABIC Innovative Plastics is a trademark of SABIC Holding Europe B.V.* LNP is a trademark of SABIC Innovative Plastics IP BV
* Thermotuf is a trademark of SABIC Innovative Plastics IP BV
©1997-2012 SABIC Innovative Plastics Holding BV.All rights reserved

原料辅料、初加工材料 > 橡胶、塑料、树脂 > 通用与工程塑料 > PP >