供应 FCC电容式非接触式电压探棒F-CVP-1
上海欧桥电子科技有限公司（网络部）
中国 上海
产品属性
图文详情
品牌推荐
品牌
型号
F-CVP-1
产地
国外
产品名称：FCC电容式非接触式电压探棒F-CVP-1
品 牌：FCC
型 号：F-CVP-1
工作带宽：9 kHz – 100 MHz
标称增益探头：- 20 dB
标称增益平坦度：(150 kHz – 30 MHz): +/- 0.2 dB
(9 kHz – 100 MHz): +/- 1.5 dB
动态范围：80 dB minimum
最小可测量的信号：(At 1kHz detection bandwidth) 10 dBuV
最大可测量的信号：约10 V
最大直径：被测电线/电缆束：2公分为小于5pf的标称负载电缆/捆测试
探头电源：内置可充电镍氢电池或镍镉，或一次性碱性电池（10 AA尺寸）
电池寿命：40 hours minimum
电池充电器：External, powered from 120 VAC
充电时间（最长）：14 hours
连接器：Type N (female)
输出连接器外形尺寸：7.7 inches High X 5.0 inches Wide X 8.0 inches Long (19.6 cm X 12.7 cm X 20.3 cm)
The Fischer Custom Communications, Inc. non-contact capacitive voltage probe (F-CVP-1) is used to measure the common mode voltage appearing between a multi-pair balanced cable bundle and the local ground reference for the cable bundle in accordance with CISPR 22 Section C.1.3. The F-CVP-1 makes this voltage measurement without requiring direct contact with the metallic conductors in the cable bundle, or requiring physically breaking the cable bundle to install the F-CVP-1.
The F-CVP-1 consists of 2 concentric metal electrodes. A capacitive voltage pider is formed by the capacitance between the cable bundle under test and the inner metal electrode of the F-CVP-1, and the capacitance between the inner and outer metal electrodes of the F-CVP-1. A Fischer Custom Communications, Inc. proprietary circuit buffers and amplifies the voltage from this capacitive pider, and provides a voltage out of the F-CVP-1 for direct input into a 50 O signal or spectrum analyzer.
The F-CVP-1 meets the critical requirement to minimize capacitive loading of cables under test. If the loading is greater than 5 pico farads the overall impedance of the cable under test can be significantly lowered and result in erroneous common mode voltage measurements.
Accessories Provided:
Rechargeable NiMH batteries
Battery Charger
Foam inserts to hold/position wire/cable under test inside CVP
Operating Manual
FCC公司的非接触式电容电压探针（F-CVP-1）被用于测量的共模电压根据CISPR多对平衡电缆束和电缆束的局部接地参考之间出现22第C.1.3。这架F-CVP-1使得这个电压测量，而无需使用金属导体直接接触的电缆束，或要求物理破坏电缆束安装在F-CVP-1。
品 牌：FCC
型 号：F-CVP-1
工作带宽：9 kHz – 100 MHz
标称增益探头：- 20 dB
标称增益平坦度：(150 kHz – 30 MHz): +/- 0.2 dB
(9 kHz – 100 MHz): +/- 1.5 dB
动态范围：80 dB minimum
最小可测量的信号：(At 1kHz detection bandwidth) 10 dBuV
最大可测量的信号：约10 V
最大直径：被测电线/电缆束：2公分为小于5pf的标称负载电缆/捆测试
探头电源：内置可充电镍氢电池或镍镉，或一次性碱性电池（10 AA尺寸）
电池寿命：40 hours minimum
电池充电器：External, powered from 120 VAC
充电时间（最长）：14 hours
连接器：Type N (female)
输出连接器外形尺寸：7.7 inches High X 5.0 inches Wide X 8.0 inches Long (19.6 cm X 12.7 cm X 20.3 cm)
The Fischer Custom Communications, Inc. non-contact capacitive voltage probe (F-CVP-1) is used to measure the common mode voltage appearing between a multi-pair balanced cable bundle and the local ground reference for the cable bundle in accordance with CISPR 22 Section C.1.3. The F-CVP-1 makes this voltage measurement without requiring direct contact with the metallic conductors in the cable bundle, or requiring physically breaking the cable bundle to install the F-CVP-1.
The F-CVP-1 consists of 2 concentric metal electrodes. A capacitive voltage pider is formed by the capacitance between the cable bundle under test and the inner metal electrode of the F-CVP-1, and the capacitance between the inner and outer metal electrodes of the F-CVP-1. A Fischer Custom Communications, Inc. proprietary circuit buffers and amplifies the voltage from this capacitive pider, and provides a voltage out of the F-CVP-1 for direct input into a 50 O signal or spectrum analyzer.
The F-CVP-1 meets the critical requirement to minimize capacitive loading of cables under test. If the loading is greater than 5 pico farads the overall impedance of the cable under test can be significantly lowered and result in erroneous common mode voltage measurements.
Accessories Provided:
Rechargeable NiMH batteries
Battery Charger
Foam inserts to hold/position wire/cable under test inside CVP
Operating Manual
FCC公司的非接触式电容电压探针（F-CVP-1）被用于测量的共模电压根据CISPR多对平衡电缆束和电缆束的局部接地参考之间出现22第C.1.3。这架F-CVP-1使得这个电压测量，而无需使用金属导体直接接触的电缆束，或要求物理破坏电缆束安装在F-CVP-1。
