产品介绍：
宠物食品生产线是专门为猫、狗等宠物生产日常食品和保健功能食品而研制开发，采用原料预处理调质系统，大幅度提高产量和降低能耗，能够满足客户对产量和品质的不同需求，同时在工艺上注重产品的适口性和科学的营养配比，使产品易于消化吸收。以此生产线为基点，我公司愿与行业内众多客商达成多层次、全方位的合作。
宠物饲料加工设备工艺组成：
1、拌粉机：根据生产线产量的不同选用不同型号的拌粉机，主要三种机型给您选择选用BFJ-I、BFJ-II、BFJ-III。
2、上料机：利用电机为动力螺旋式输送，确保上料方便快捷。
3、膨化机：根据生产线产量的不同选用不同型号的膨化主机，产量可从100kg/h--600kg/h不等，可以玉米粉、谷粉、骨粉、肉粉等为原料，具体产品形状可更换模具。
4、提升机：将饲料输送到烤箱，提升机的高度根据烤箱确定，也可选用风送机。
5、多层烤箱：烤箱多为电烤箱，温度在0-200度之间通过控制柜自行调节，内部为不锈钢双层网袋，烘烤时间可以根据速度调节，有三层、五层、七层不锈钢烤箱；
6、调味线：有八角筒、圆筒、提升单滚筒、双滚筒调味线，根据产量、产品性质配置，
7.振动筛：筛去多余碎料以及多余的外撒料，确保包装
膨化机的保养
1、箱体轴承应及时加注润滑油脂，运行500小时后，要全部更换一次润滑油脂。(新机器运行前应适量加入润滑脂，运行200小时后应当换油。)
2、其他轴承部位要定期加注润滑脂。
3、螺杆、螺套等易损件在拆装过程中严禁用硬物重锤，在膨化腔上严禁放置重物或者站人。进口泵 阀门
4、膨化原料应经过清理，严防金属等异物进入机内损坏机件。
5、随时检查膨化机质量，注意更换易损件。
6、保持设备周围的清洁。
7、长期停机不用或更换膨化物料时，应将膨化腔内的物料清除干净，以免结块、霉变或者物料之间交叉污染。
8、由于接近出料口处的易损件磨损相对较快，靠近进料口一端的易损件磨损较少，所以在更换易损件时，应从出料端开始依次更换，不宜一次更换多种部件。
Maintenance of the extruder
1, the box bearing should be filled with lubricating oil in time. After 500 hours, all the grease should be replaced. (the lubricating grease should be added to the new machine before running, and the oil should be changed after running for 200 hours. " )
2, other bearing parts should be regularly filled with grease.
3, screw and screw sleeve parts in the process of disassembly prohibited hammer with hard objects, in the extrusion chamber is prohibited to place heavy objects or stand. Inlet pump valve
4, the extruded raw materials should be cleaned up, and the metal and other foreign objects should be strictly prevented from entering the machine.
5, check the quality of the extruder at any time, and pay attention to changing the vulnerable parts.
6, keep the cleaning around the equipment.
7. When the expansion material is not used or replaced for a long time, the material in the extruded cavity should be cleaned up so as to avoid caking, mildew or cross contamination between materials.
8, because the wearing parts near the outlet are relatively fast wear, and the wearing parts near the inlet end are less worn. Therefore, when changing the vulnerable parts, it is necessary to replace them at the beginning of the discharge terminals, so it is not suitable to replace multiple parts at a time.
加工样品
产品布局：
