MG 690 TIG

MATERIAL SAFETY DATA SHEET
MAY BE USED TO COMPLY WITH OSHA'S HAZARD COMMUNICATION STANDARD, 29 CFR 1910.1200 AND SUPERFUND AMENDMENTS
AND REAUTHORIZATION ACT (SARA) OF 1986 PUBLIC LAW 99-499. STANDARD
SHOULD BE CONSULTED FOR SPECIFIC REQUIREMENTS.

SECTION I (IDENTIFICATION)

MANUFACTURER/ MG Systems & Welding, Inc. TELEPHONE NUMBER:
SUPPLIERS NAME: N94 W14355 Garwin Mace Drive (262) 255-5520
Menomonee Falls, WI 53051 USA


PRODUCT NAME: MG 600 Mig/Tig, MG 610 Mig/Tig, MG 650 Mig/Tig, MG 660 Mig/Tig, MG 690 Mig/Tig

PRODUCT CLASSIFICATION: Bare Filler Metal

SECTION II (HAZARDOUS INGREDIENTS/IDENTITY INFORMATION)
IMPORTANT: This section covers the materials from which these products are manufactured. The fumes and gases produced during normal use of these
products are covered in Section V. The term "Hazardous" in "Hazardous Ingredients" should not only be interpreted as a term required and defined in OSHA
Hazard Communication Standard (29 CFR Part 1910.1200), but also as defined by other regulatory agencies. The chemicals or compounds subject to
reporting under Title III, in Section 313, of the Superfund Amendments and Reauthorization Act (SARA) are marked by the symbol #.

WARNING: This product contains or produces a chemical known to the State of California to cause birth defects (or other reproductive harm) and cancer.
(California Health & Safety Code 25249.5 et seq.)


CAS Exposure Limit (mg/m3
) MIG AND TIG WIRE
INGREDIENTS NUMBER OSHA PEL ACGIH-TLV 600 610 650 660 690
Nickel # 7440-02-0 1 0.2 F G F G L
Iron 7439-89-6 10 (as Fe) 5 (as Fe) K J L L C
Silicon 7440-21-3 5 10 A A A A A
Molybdenum 7439-98-7 5 0.5 A A A C
Chromium # 7440-47-3 1 0.5 H G G G G
Niobium (Columbium) 7440-03-1 5 5 - - - - C
Manganese # 7439-96-5 5 (ceiling) 0.2 C C C C C



PERCENT RANGE CODE (by Weight):
A = 0.1 - 1% C = 1 - 5 % E = 5 - 10% G = 10 - 30% J = 30 - 60% L = 60 - 100
B = 0.5 - 1.5% D = 3 - 7% F = 7 - 13% H = 15 - 40% K = 40 - 70%

SECTION III (PHYSICAL DATA) - Welding wire.

SECTION IV (FIRE AND EXPLOSION HAZARD DATA)
Non-Flammable: Welding arc and sparks can ignite combustibles. Refer to American National Standard Z49.1 for fire prevention during welding. These
products as shipped are non-hazardous, nonflammable, non-explosive, and non-reactive.
Rating under National Fire Protection 704: Health, 1: Flammability, 0: Reactivity, 0.

SECTION V (REACTIVITY DATA)
Welding fumes cannot be classified simply. The composition and quantity of both are dependent upon the metal being welded, the process, procedure, and
the wire used. Other conditions which also influence the composition and quantity of the fumes and gases to which workers may be exposed include:
coatings on the metal being welded (such as paint, plating, or galvanizing), the number of welders and the volume of the work area, the quality and the








amount of ventilation, position of the welder's head with respect to the fume plume, as well as the presence of contaminants in the atmosphere (such as
chlorinated hydrocarbon vapors from cleaning and degreasing activities).

When the wire is consumed, fume and gas decomposition products generated are different in percent and form from the ingredients listed in Section II. Fume
and decomposition products, not the ingredients in the wire, are important. Decomposition products include those originating from the volatilization,
reaction, or oxidation of materials in Section II, plus those from the base metal, etc., as noted above. These components are virtually always present as
complex oxides and not as metals (Characterization of Arc Welding Fume: American Welding Society). Reasonably expected fume constituents of the fume
could include complex oxides of iron and manganese. Chromium and nickel oxides would also be present. The table below lists reasonably expected fumes
that may be generated:

品牌：美国Messer