| Stands | ||||||||||||||||||||
|
GB/T 11017-2002《额定电压110kV交联聚绝缘电力电缆及其附件》 GB/T 11017-2002:Power cables with cross-linked polyethylene insulation and their accessories for rated voltage of 110kV. IEC 60840:1999 《额定电压大于30kV（Um=36kV)至150kV（Um=170kV）挤包绝缘电力电缆及其附件-试验和要求》 IEC 60840:1999 Power cables with extruded insulation and IEC 60840:1999 Power cables with extruded insulation and their accessories for rated voltages above 30kV(Um=36kV)up to 150kV (Um=170kV) methods and requirements |
||||||||||||||||||||
| 特性与用途Propety and Function | ||||||||||||||||||||
|
交联聚绝缘电力电缆导体工作温度高，传输容量大，电气性能优良，电费附件简单安装敷设方便等优点，因此在当今电力中使用广泛。 Cross-linked polyethylene insulated power cable are featured with high allowable working temperature of conductor,huge transmission capacity,excellent electric properties,simple cable accessories and convenient installment and laying, so that they are widely used in the power system today. 电缆适用于工频额定电压为64/110kV（Um=126kV),中心点直接接地的输电线路。 The cable can be applied to the neutral-point solid grounded power transmission line system with AC.rated voltage 64/110kV(Um=126kV). |
||||||||||||||||||||
| 使用特性Properties of Applition | ||||||||||||||||||||
|
1.电缆正常运行时导体允许的长期高温度为90℃ 1.During the normal operation of cables,the max permissible continuous operation temperature of conductor should not exceed 90℃ 2.短路时（长时间不超过5秒）电缆导体允许的高温度为250℃。 2.Conductor short-circuit temperature should not exceed 250℃(when max sustaining period will not exceed 5 seconds). 3.电缆安装时允许的小弯曲半径一般为电缆直径的25倍。 3.The min permissible bending radius during the cable laying is normally 25 times of the diameter of cables. 4.电缆敷设时不受落差。 4.Free from restrictions of level difference along the route during the cable laying. 5.低于0℃敷设时，必须预先加温。 5.Pre-heated is needed when the temperature is below 0℃ during the cable laying. |
||||||||||||||||||||
| 型号名称 Type and Description | ||||||||||||||||||||
|
||||||||||||||||||||
| 规格 Specification | ||||||||||||||||||||
|
||||||||||||||||||||
遂宁电缆附件110 110KV电缆头价格
设备用途 电力排风GB/T9124-2000 钢制法兰技术条件 5 030211008001 接地装置 接地极调试 接地电阻 2产品检验分出厂检验和型式检验。有下列情况之一时应进行型式检验：LT3104P15001 消防灭火装置 1.消防灭火装置:详见图纸 项 1 LA2103B14003 埋管内敷设(ADSS光缆) "1.型号、规格:GYFTZY-48B1光缆 2.单盘测量:3 3.全程测量:1 4.接续:2" km 1 2.3 工程条件序号 项 目 单 位 参数值 投标人保证值
