HQHL系列冷凝机组技术数据 | |||||||
机组型号 MODEL | HQHL-13EBR | HQHL-16EBR | HQHL-23EBR | HQHL-30EBR | HQHL-36EBR | ||
名义输出功率 NORMAL OUTPUT(W) | 700 | 900 | 1200 | 1500 | 1600 | ||
电 源 POWER SUPPLY | 单相220V/50Hz | ||||||
使用工质最大加液量 REFRIGERANT MAX.(Kg) | R22(1.2) | R22(1.5) | R22(2.0) | R22(2.5) | R22(2.5) | ||
启动电流 START-UP CURRENT(A) | 22 | 27 | 38 | 42 | 42 | ||
最大负载电流MAX. LOAD CURRENT (A) | 4.0 | 5.1 | 6.5 | 8.0 | 8.5 | ||
蒸发温度范围 EVAP.TEMP.(℃) | -40～-5 | ||||||
使用环境温度范围 AMBIENT TEMP.(℃) | 0～40 | ||||||
压缩机(型号) COMPRESSOR (MODEL) | QHL-13E | QHL-16E | QHL-23E | QHL-30E | QHL-36E | ||
冷凝器CONDENSER | 规 格 STYLE | 3排5环 | 4排5环 | 4排5环 | 4排5环 | 4排5环 | |
风扇 电机FAN MOTOR | 风扇直径 DIAMETER (mm) | φ230*2 | φ230*2 | φ230*2 | φ230*3 | φ230*3 | |
风量 AIR FLOW (m³/hr) | 680*2 | 950*2 | 950*2 | 950*3 | 950*3 | ||
接管PIPE (mm) | 吸气口(直径)GAS INLET DIAM | φ12.7(1/2") | |||||
液体出口(直径)LIQUID OUTLET | φ9.53(3/8″) | ||||||
外形 尺寸OUT DIMENSION | 长 LENGTH (mm) | 680 | 680 | 790 | 940 | 1145 | |
宽 WIDTH (mm) | 485 | 485 | 520 | 520 | 520 | ||
高 HEIGHT (mm) | 275 | 275 | 275 | 275 | 275 | ||
成品重量WEIGHT(Kg) | 31.1 | 33 | 39.7 | 48.5 | 53.4 | ||
制冷量CAPACITY | 蒸发温度EVAP. TEMP.(℃) | 制冷量 REFRIGERATION CAPACITY:W(Kcal/h) 冷凝温度 CONDENSING TEMP.:45℃ 环境温度 AMBIENT TEMP.:32℃ | |||||
-40 | 410(355) | 505(434) | 670(580) | 845(730) | 952(819) | ||
-35 | 532(458) | 650(560) | 820(709) | 1136(982) | 1245(1071) | ||
-30 | 656(563) | 800(688) | 1005(870) | 1392(1205) | 1550(1334) | ||
-25 | 793(682) | 969(833) | 1240(1070) | 1718(1483) | 1978(1701) | ||
-20 | 969(833) | 1183(1017) | 1500(1295) | 2029(1752) | 2406(2069) | ||
-15 | 1164(1000) | 1421(1223) | 1840(1590) | 2489(2151) | 2881(2478) | ||
-10 | 1416(1217) | 1728(1486) | 2125(1825) | 2875(2469) | 3342(2874) | ||
-5 | 1672(1438) | 2042(1756) | 2440(2095) | 3311(2835) | 3894(3349) | ||
接线容量 WIREING CAPACITY | 漏电保护器 LEAKAGE PROTECTER | 额定电流 RATED CURRENT(A) | 10 | 10 | 15 | 20 | 25 |
泄漏电流 LEAK CURRENT≤(mA) | 30 | 30 | 30 | 30 | 30 | ||
线径DIAMETER（mm²） | 10m以内 IN 10m | 2.0 | 2.0 | 2.0 | 4.0 | 4.0 | |
20m以内 IN 20m | 2.0 | 2.0 | 2.5 | 5.5 | 5.5 | ||
30m以内 IN 30m | 2.0 | 2.0 | 2.5 | 5.5 | 5.5 | ||
注意:1.应尽量控制冷媒充注量,最多不能超过表中值; | |||||||
2.吸气管及蒸发器管径应考虑回油并再次确认流速后确定; | |||||||
3.替代R12机型时管径选择应注意保证气体流速在横管内达到3.8m/s以上, | |||||||
在竖管内达到7.6m/s以上; | |||||||
4.单侧管长应在10m以下,此时高差应在3m以下. | |||||||
Note: | |||||||
1.The refrigerant charge must be controlled strictly.The maximize limitation of charging is listed in the table. | |||||||
2.Diameter of the suction and evaporating pipes should be decided by oil circulation and reconfirmation of gas | |||||||
speed. | |||||||
3.The diameter of pipes must guarantee the gas speed of | |||||||
vertical ones. | |||||||
4.The single sided pipe length is 10m;with height difference should be within 3m. | |||||||
This serial units adopt horizontal compressor! | |||||||
