家用井泵|井用抽水泵|抽深井水用泵|抽井水泵使用范围此款不锈钢深井泵不适用于易燃,易爆液体最大潜水深度40m最高液体温度40℃最大含沙量:10g/1酸碱度PH值:
6.5-8.5氛离子含量<400mg/1 SCOPE OF USAGEThe pump is not suitable for inflammable or explosive liquids!-Maximum immersion dcpth:40m-Maximum temperature of pumped liquid:40℃-Maximum quantity of sand in water:10g/1(Hydrogen factor)PH value:6.5-8.5The concentration of chlorides:<400mg/1 安装说明1.不允许水泵脱水干运转。流入水泵的水平面绝不能低于水泵不锈钢进水过滤网孔。
2.在使用泵之前,若有需要,建议用钢丝绳或尼龙绳把泵从井里吊上来或把泵放进井里。
3.先确保井里没有沙子,并有足够的空间去安放泵。
4.在进行操作之前一定要将地线可靠接地。
5.单相电机必须配备我们的控制盒,包括也容器和电流保护装置。
6.三相电机必须用一个合适的控制盒把水泵连接到三相供电线上。
7.水泵和三相电机如果接线错误,产生旋转方向错误会引起流量的下降。正确的旋转方向是水泵能供应最大流量的位置。 INSTALLATLON1.Never allow the pump to operate dry!This means that liquid level in pump must higher than level of holes on the blttom of stainless steel intake filter.2.It is advisable to use steel or nylon rope to hook the pump when you need to remove pump from the well or place it in the well.3.Before situating the pump,make sure that the well is free of sand ,straight,and has sufficient width to guarantee passage of the pump.4.Make the earth connection before carrying out any operation.5.Single-phase;Single-phase motors must be supp-lied with our cotrol boards containing conde-nser and amperometric protection.6.There-phase version;The pump mump must be hooked up to the three-phase supply ling using a suitable control board.7.Rotation in the wrong direction causes a noticeable reduction in capacity and prevalence.The correct rotation direction is that relative to the position of the phases in which the pump supplies the grea-test capacity and prevalence.
深井泵特点1.不锈钢防腐结构2.工程叶悬浮设计3.陶瓷抗沙结构耐磨损4.销子花键连接易保护5.内置环保防冻水6.自调心石墨轴承7.入水深度可达300米8.可重绕水浸绕组
Pump characteristics1.the structure,stainless steel2.engineering design leaves float3.to wear,sandy structure4.and ils take to protect5.Internal environmental water6.From the heart of the graphite7.the depth of water up to 300 meters8.may be rewound flooding winding
4sp3\4sp5\4sp8 pump parameter
型号 Type 电压Voltage
V 功率Power
(KW) 额定扬程
Rting
M
额定流量 Rating flow
T 长度mm 重量kg
出水口径 Water with 外径mm Diameter4SP3-58/12-0.75
220/380
0.75
58
3
404
3.75
1.2"
964SP3-77/16-1.1
220/380
1.1
77
3
488
4.55
1.2"
964SP3-106/22-1.5
220/380
1.5
106
3
614
6.35
1.2"
964SP3-154/35-1.2
220/380
1.2
154
3
824
7.35
1.2"
964SP3-217/45-3.0