H71对夹式止回阀、H71W对夹式止回阀的特点介绍
对夹式止回阀是一种通用单向流体。其重量轻，体积小，容易安装在法兰之间,阀门内部由两个半圆弹簧和板面组成，用销子固定在阀体上,弹簧形变使阀板关闭，流体压力又使其开启弹簧的形变很快，这样能保护管道免受水锤破坏。
H71对夹式止回阀，又称为H71W对夹式止回阀，也就是对夹式止回蝶阀。采用对夹式连接，结构紧凑，阀门的阀瓣沿着中心定位作 升降运动，由于阀瓣的关闭行程短，并有弹簧加载，关闭速度快，可显著减少水锤现象。产品具有体积小、重量轻、动作灵敏、密封可靠、安装方便等特点，特别适合于安装空间受限制的场合采用，可适用于水、蒸气、油品、硝-酸、醋酸、强氧化性介质等多种介质。
安装注意事项：
1、放置管道时应注意使对夹式止回阀的通过方向与流体流向一致,安装在垂直放置的管路中。
2、对于水平放置的管路，垂直放置对夹式止回阀
3、在阀门的阀板操作半径范围内，避免加入管接头和阻塞物
4、在弯头附近安装对夹式止回阀时，要注意留有足够大的空间
5、不要在对夹式止回阀的前面或者后面安装一个变径管
5、在水泵出口安装对夹式止回阀时，至少留出六倍阀门直径的空间以保证阀板最终受到流体作用
配管法兰 | 公称压力 | 常规产品型号 | ||||||
JB/T 74 | PN1.0MPa | H71H-10C | H71W-10P | H71W-10P8 | H71W-10P3 | H71W-10R | H71W-10R8 | H71W-10R3 |
PN1.6MPa | H71W-16C | H71W-16P | H71W-16P8 | H71W-16P3 | H71W-16R | H71W-16R8 | H71W-16R3 | |
PN2.5MPa | H71W-25 | H71W-25P | H71W-25P8 | H71W-25P3 | H71W-25R | H71W-25R8 | H71W-25R3 | |
PN4.0MPa | H71W-40 | H71W-40P | H71W-40P8 | H71W-40P3 | H71W-40R | H71W-40R8 | H71W-40R3 | |
PN6.3MPa | H71W-63 | H71W-63P | H71W-63P8 | H71W-63P3 | H71W-63R | H71W-63R8 | H71W-63R3 | |
PN10.0MPa | H71W-100 | H71W-100P | H71W-100P8 | H71W-100P3 | H71W-100R | H71W-100R8 | H71W-100R3 | |
PN16.0MPa | H71W-160 | H71W-160P | H71W-160P8 | H71W-160P3 | H71W-160R | H71W-160R8 | H71W-160R3 | |
GB/T 9112 | PN2.0MPa | H71H-20C | — | H71W-20P8 | H71W-20P3 | — | H71W-20R8 | H71W-20R3 |
PN5.0MPa | H71H-50 | — | H71W-50P8 | H71W-50P3 | — | H71W-50R8 | H71W-50R3 | |
PN11.0MPa | H71H-110 | — | H71W-110P8 | H71W-110P3 | — | H71W-110R8 | H71W-110R3 | |
PN15.0MPa | H71H-150 | — | H71W-150P8 | H71W-150P3 | — | H71W-150R8 | H71W-150R3 | |
ANSI B 16.5 | Class150 | H71H-A1C | — | H71W-A1P8 | H71W-A1P3 | — | H71W-A1R8 | H71W-A1R3 |
Class300 | H71H-A3 | — | H71W-A3P8 | H71W-A3P3 | — | H71W-A3R8 | H71W-A3R3 | |
Class600 | H71H-A6 | — | H71W-A6P8 | H71W-A6P3 | — | H71W-A6R8 | H71W-A6R3 | |
Class900 | H71H-A9 | — | H71W-A9P8 | H71W-A9P3 | — | H71W-A9R8 | H71W-A9R3 | |
主 要 | 阀体 | WCB(A105) | ZG1Cr18Ni9Ti | CF8(304) | CF3(304L) | ZG1Cr18Ni12Mo2Ti | CF8M(316) | CF3M(316L) |
阀瓣 | 2Cr13 | 1Cr18Ni9Ti | 0Cr18Ni9 | 00Cr19Ni10 | 1Cr18Ni12Mo2Ti | 0Cr17Ni12Mo2 | 00Cr17Ni14Mo2 | |
压圈 | 2Cr13 | 1Cr18Ni9Ti | 0Cr18Ni9 | 00Cr19Ni10 | 1Cr18Ni12Mo2Ti | 0Cr17Ni12Mo2 | 00Cr17Ni14Mo2 | |
弹簧 | 0Cr18Ni9 | 0Cr18Ni9 | 0Cr18Ni9 | 00Cr19Ni10 | 0Cr17Ni12Mo2 | 0Cr17Ni12Mo2 | 00Cr17Ni14Mo2 | |
适 用 | 适用介质 | 水、蒸汽、油品等 | 硝酸等腐蚀性介质 | 强氧化性介质 | 醋酸等腐蚀性介质 | 尿素等腐蚀性介质 | ||
适用温度(℃) | -29~425 | -196~540 | -196~425 | -196~540 | -196~455 | |||
注：本表为常规对夹式止回阀的型号编制、主要零件材料及适用工况，其他要求及其型号编制参见对夹止回阀型号编制方法。 | ||||||||
