DC-005-3.0/插座
东莞市黄江科铭电子厂
中国 东莞
产品属性
图文详情
品牌推荐
品牌/型号
DGKM1995/DC-005-3.0
接口类型
AC/DC
接触件材质
全铜
针数
3.0
种类
插头/插座
加工定制
是
形状
圆形
应用范围
电源
型号
DC-005-3.0
工作频率
高频MHz
特性
阻火/阻燃
品牌
DGKM1995
绝缘体材质
塑胶
支持卡数
单卡
芯数
6.8
制作工艺
注塑
| 规 格 书 | |||||||||
| SPECIFICATION | |||||||||
| DESIGNATION | 系列: JACKS | ||||||||
| MODEL | 型号:DC-005-3.0 | ||||||||
| 1.RATING | 额定值:AC 250V 6(10)A | ||||||||
| 2.CONSTRUCTION DIMENSION结构尺寸： | Apply to the appended drawing：符合附加图纸 | ||||||||
| 3.APPEARANCE外观： | Have no remarkable damage,arack and rust etc:无明显损伤,裂纹,锈迹等. | ||||||||
| ITEM专案 | TEST CONDITON测试条件 | SPECIFICATION规格 | |||||||
| 4.ELECTRONICAL CHARACTERISTICS.电气性能. | |||||||||
| 4A | CONTACT RESISTANCE | Being measured 1KHZsmall current comtact | 50mΩmax. | ||||||
| 接触阻抗 | resistance meter.在1KHZ小电流下测量. | 50毫欧以下. | |||||||
| 4B | INSULATION | Measurements shall be mabe following application | 100MΩ min. | ||||||
| RESISTANCE | of DC 500V potetial across terminals and across | 100兆欧以上. | |||||||
| 绝缘阻抗 | terminals and frame for 1 minute .在端子之间和端 | ||||||||
| 子与壳之间加DC 500V条件下,持续1分钟测量. | |||||||||
| 4C | WITHSTAND | AC 500V (50Hz or 60Hz) shall be applied across | There shall be no breakdown. | ||||||
| VOLTAGE | terminals and across terminals and frame for one | 无击穿现象出现. | |||||||
| 耐电压 | minute在端子之间和端子与壳之间加A C | ||||||||
| 500V (50HZ或60HZ)条件下,持续1分钟测量. | |||||||||
| 5.MECHANICAL CHARACTERISTICS.机械性能。 | |||||||||
| 5A | INSULATION AND | Being measure at across spring piece and across | Insertion and extraction | ||||||
| WITHDRAW | matching plug for ergomter | force 3-20N | |||||||
| FORCE插拔力 | 用测力半在插头与弹片之间进行测量。 | 插拔力 3-20N | |||||||
| 5B | TERMINAL STRENGTH | A static force of 500gf being applied in one | There shall be no sugn of damage | ||||||
| 端子强度 | direction on the tip lf terminal for 1 minute.一个 | mechanically and electically.无 | |||||||
| 克之静负荷施加於端子顶部的一个方向持续 | 任何迹象显示机械及电气性 | ||||||||
| 1分钟。 | 能之损坏。 | ||||||||
| 6.DURABILITY.耐久性. | |||||||||
| 6A | SOLDERING | The tip of the terminals shall dipped 2mm in the | A new uniform coating of solder shall | ||||||
| TEST. | solde bath at a temperature 230±5℃for 3± | cover a minimum of 75 of the surface | |||||||
| 可焊性试验 | 0.5sec.端子顶部被浸入焊锡池2mm深,温度230± | being immersed.浸入的部分75%以上 | |||||||
| 5℃时间3±0.5秒. | 表面将被锡覆盖. | ||||||||
| 6B | LIFE TEST. | 10,000 cycles of operation at a rate of 20-30 | (1).Contact resistance.40mΩ max | ||||||
| 寿命试验 | cycles per minute with unloading. | 接触阻抗40毫欧以下. | |||||||
| 无负载条件下,每分钟20-30次的速度操作 | (2).Insertion and withdraw force 30 | ||||||||
| 10,000次 | initial value插拔力变化范围初始值30% | ||||||||
| (3).ITEM专案-4B，-4C，-5B | |||||||||
| 6C | HEAT TEST。 | 85±2℃for hours after test keep in normal condition | (1).Contact resistance.50mΩmax接触 | ||||||
| 耐热试验 | for 30 minutes .在85±2℃环境中放48小时， | 电阻50毫欧以下 | |||||||
| 再放在正常环境中30分钟后进行测试。 | (2).Insertion resistance 50mΩmin | ||||||||
| 6D | HUMIDITY TEST。 | The condition of temperature 40±2℃and humidty | 绝缘电阻兆欧以上 | ||||||
| 耐湿试验 | 90-95%for 48 hrs.after test keep in normal | (3).There shall be no sign of damage | |||||||
| condition for 30min.在温度40±2℃，湿度 | mechanically and electically.无任何迹 | ||||||||
| 90-95%环境中放48小时，再放在正常中 | 象显示机械及电气性表面将 | ||||||||
| 30分钟后进行测试。 | 之损坏. | ||||||||
| 6E | COLD TEST。 | At-30±2℃for 48 hrs.after test keep in normal | |||||||
| 耐冷试验 | condition for 30 min.在-30±2℃环境中放48小时， | ||||||||
| 再放置于正常环境中30分钟后进行测试。 | |||||||||
