UK HOLDTITE 耐高溫瞬間膠CA200，可耐高溫200度的瞬間膠，業界最強，已經得到客戶認證確認。
TECHNICAL INFORMATION (TDS 40)
| RESIST©200 | ||
| High Temperature Speciality Cyanoacrylate.
| ||
DESCRIPTION Resist© 200 is unmatched in performances when compared to Ethyl, Ethoxy and Methyl Cyanoacrylates where maximum temperature reaches only 120C, with significantly reduced % of ultimate bond strength. Resist© 200 out performs all other Cyanoacrylates for Temperature Resistance.
APPLICATIONS Intermittent or constant exposure to elevated temperatures, extremes of temperatures up to 200C. Post curing to an even Higher Strength @ 175C to form Temperature Resistant bonds on most Metals, Rubbers etc.
USEFUL HINTS/NOTES Use Resist© 200 to hold components in place on circuit boards where wave soldering temperatures kill other superglues.
PROPERTIES When heating up items after bonding, 30 minutes @ 150C above will increase strength by 40% of cold bond strength and influence the products long term resistance to its fullest once cured.
INSTRUCTIONS FOR USE Ensure parts are clean, dry and free from oil and grease.
PROCEDURE FOR APPLICATION Apply sparingly to one side and hold parts until handling strength is achieved.
COMPATIBLE ACCELERATORS/PRIMERS Not recommended, but the following primers such as A021 or Double Strength A113 as accelerators for fillet cure for priming absorbent surfaces will help speed cure the material. REV: 21-09-99 HH | TECHNICAL FEATURES
Resin…………………………………Allyl 2 Cyanoacrylate Colour……………………………….Clear Cure Speed With Activator……….…Not recommended Cure Speed Without Activator………<30 seconds Viscosity….………………………….6-20cps Gap Fill………………………………0.05 mm Flash Point…………………………..>90°C Shelf Life……………………………12 months @ 20C Specific Gravity……………………..1.06 Max. Operating Temperature……….-30°C to + 200°C
CURED PERFORMANCE Fixture Time:……………………….. <40 seconds Refractive Index:…………………… 1.46 Dielectric Constant:………………… 3.5 @ 10kHz Volume Resistivity:………………… 8.6 x 10(2) Ohm.cm Post Cure @ 175C…………………. 10 minutes Tensile Strength:…………………… 36 N/mm2 Tensile Shear Strength - Steel;…….. 22 N/mm2 - Plastic…… 35 N/mm2 - Viton……. 8 N/mm2* *Substrate Failure
STORAGE Store in a cool area out of direct sunlight Refrigeration to 5C gives optimum storage stability.
PRESENTATION Bottles:…………………………………..20g, 50g, 500g
HEALTH & SAFETY IN USE DANGER -Superglue bonds skin and eyes in seconds. If accidental skin bonding happens wash with warm soapy water and prise skin apart using a blunt instrument (such as a teaspoon handle). In case of eye contact, bathe immediately with water and seek immediate medical attention.
| ||
| The information contained herein is produced in good faith and is believed to be reliable but is for guidance only. Holdtite and its agents cannot assume liability or responsibility for results obtained in the use of its products by persons whose methods are outside or beyond our control. It is the users responsibility to determine the suitability of any of the products and methods of use or preparation prior to use mentioned in out literature and furthermore the users responsibility to observe and adopt such precautions as may be advisable for the protection of personnel and property in the handling and use of any of our products. |
| |
厚泰工业特殊瞬间胶提供优良之接着特性,结合最新技术及工业生产需求,本系列产品可充分满足各工业上的特殊沾接要求,如特殊基材..低气味.低白化等.
厚泰瞬间胶尚有以下特点:
1.具一般瞬间胶所无法承受之耐高温特性,200'c仍有优良之强度.
2.可沾接困难接着之塑料材质,如Teflon,Sillicon,PP.PET等.
3.超低粘度超快硬化速度,对于困难接着之弹性体效果良好.
4.针对潮湿环境下仍具有良好的强度之接着.
5.可用再具酸性的工作表面.
6.较高的大耐老化特性.
7.质量稳定.
