POF-LED光源机
使用电压:12VDC 220V/50Hz
灯泡类型:LED
灯泡功率:1W/3W/5W/16W
灯泡寿命:50000h-100000h
耦合头最大孔径:18mm
外形尺寸:L125×W95×H55
重量约:1kg
POF-－T光源机
使用电压:220V/50Hz
灯泡类型:陶瓷金卤灯
灯泡功率:150W/250W
灯泡寿命:3000h~6000h
耦合头最大孔径:30mm
外形尺寸:L340×W290×H150
重量约:8kg150W铝材同步型光源器使用说明书此光源器是本公司专为塑料光纤而监制的光源，采用光电转换率最高的金属气体放电灯。光效高、耗电少、安全性强，是目前用于光纤照明的最佳光源，充分体现光纤独特的效果。一、技术参数:型 号：ZWVb13-J150外型尺寸：315 × 285 × 180整机重量：8.5kg耦 合 头：PG36额定电压：AC220V/50～60Hz额定电流：0.9A整机功率：190W电 机：定向电容电机输出光色：红 、黄 、蓝 、绿 、紫 、白，共6色灯泡型号：HQI-T150W/NDL灯泡寿命：6000h显 色 性： ≥83光 通 量：6000Lm环境温度：-20℃～45℃二、使用方法：1. 将光纤捆扎好后剪平，置入光纤耦合头里面，光纤受光面与耦合头端面平齐，将耦合头插入耦合座内，拧紧耦合头上的固定螺丝。2.接通电源，打开电源开关。3.采用总开关控制方式，所有光源器采用一个电源开关控制，开机30秒之前光源器色盘自动选色，开机30秒后所有光源器达到同色同步效果。4.正常情况下，电源开关指示灯亮，排风扇工作，光源有闪烁现象，并逐渐趋于稳定，约5分钟后达到最高亮度，断电后须间隔5分钟才可再次通电，这样可延长灯泡的使用寿命。5.光纤耦合头附近的红色开关为定色变色转换按钮，按下它，光源器被定色，再按下它，光源器变色。三、注意事项：1.光源器放置的位置：要求通风良好并能防水，与周围建筑物距离不应小于100mm，须放置平稳以免滑动，不能直接放置室外环境。2.使用220V/50Hz的交流电源，用电线路要有地线。不能随意频繁开关，以免降低灯泡使用寿命。3.光源器在通电5分钟后达到正常运转，断电后须间隔5分钟才可再次通电。内置的过热保护装置在温度超过90℃时会自动断开灯泡电源，温度恢复正常则自动通电。4.所有需要同步的光源器必须同时通电，才能达到同色、同步效果。 150W Aluminum-based synchronized light sources Manual The light source is the optical fiber light source we producer for plastic optical fiber , use the highest rate photoelectric conversion of metal gas discharge lamp. High luminous efficiency, low power consumption, strong security.it is the best source for fiber-optic lighting, fully embodies the unique optical effect.一、Technical parameters:Model: ZWVb13-J150Dimensions: 315 × 285 × 180Gross Weight: 8.5kgCoupling head: PG36Rated voltage: AC220V/50 ~ 60HzRated current: 0.9ATotal Power: 190WMotor: Directional Capacitor MotorOutput light color: red, yellow, blue,green, purple, white, 6-colorBulb Type: HQI-T150W/NDLLamp Life: 6000hColoration: ≥ 83Luminous flux: 6000LmAmbient temperature: -20 ℃ ~ 45 ℃Fiber installation root number: φ0.75optical fiber 1300, φ1optical Fiber 800二、use1. bundle the optical fiber and cut flat, put into optical fiber coupling, optical fiber by the smooth face flush with the coupling head, insert the coupling head into coupling seat, tighten the screw in the coupler.2、Connected to the power and turn the power switch3、Using the master switch control, all light source using a power switch control, the light source palette selecting color automatically 30 seconds before start, after start 30 seconds , all the light source to the same color and synchronization effect.4. Under normal circumstances, the power switch indicator light, fan work, there is flickering light source and gradually stabilized, about 5 minutes after the highest brightness.5. red button near the front panel coupler of light source for the Color fixative and Switch button, press it, light source can be color, then press it, light source device can change color.三、Notes1.Light source placed: requires a well-ventilated and waterproof, With the surrounding buildings not less than 100mm distance, shall be placed smoothly so as not to slide, and can not be placed directly on the outdoor environment.2.Using 220V/50Hz AC power, power wire should be ground lines.Frequently switch at liberty is not allowed.,so as not to reduce the lamp life.3.In the power light source to normal operation after 5 minutes, must be re-energized 5 minutes interval after power failurer. When built-in thermal protection at temperatures over 90 ℃, the power will automatically disconnect the bulb, until temperature returned to normal.4. All light source must be energized at the same time, to achieve the same color, synchronization effects.
