过UL认证的白色电源适配器5V2A白色充电器美规过ETL/UL认证
深圳市明鑫电源技术有限公司
中国 深圳
产品属性
图文详情
品牌推荐
品牌
MX
型号
MX12X6-0502000
适用机型
各种平板电脑
输入电压
100-240V
输入电流
0.35A
输出电压
5V
输出电流
2A A
电源功率
10W
连接器
USB 和线
颜色
黑色和白色
有CB,CE GS认证的5V2A超薄超小体积电源适配器
1、描述/ DESCRIPTION:
本规格书适应于MX12X6-0502000VU型号的开关电源.
The purpose of the document is to specify the functional requirements of a 10W switching power supply.
2、输入特性/INPUT CHARACTERISTICS:
2.1输入电压/Input Voltage:
额定电压/Rated Voltage:100-240Vac
调整范围/Variation Range:90-264Vac
2.2输入频率/Input Frequency:
额定频率/ Rated Frequency: 50-60Hz.
调整频率/Variation Frequency:47-63Hz
2.3输入电流/Input Current:
当输入交流电压为额定值的下限电压负载满载时,最大输入交流电流0.35A.
0.35Amps max At any input voltage and rated, DC output rated load.
2.4浪涌电流/Inrush Current:
冲击电流峰值在额定电压输入，冷启动（25℃）时，不大于30A;且在任何负载和输入条件下，不导致永久性损坏或危险.
Impact current peak in the rated voltage input, cold start (25 ℃), not more than 30 a;
And in any load and input conditions, don't cause permanent damage or dangerous.
2.5AC漏电流/Ac Leakage Current:
当输入电压240Vac时,最大漏电流为0.25mA./ 0.25mA Max.At240Vac input.
3、输出特性/OUTPUT CHARACTERISTICS:
3.1输出功率/Power output
3.2输出特性/Output Characteristics
3.3纹波和噪音Ripple and Noise:
测试条件:在输入115/230Vac 25℃和输出最小及最大负载时，使用示波器带宽为20MHz连接到适配器的输出端，同时输出端并联一个47uF的电解电容和一个0.1uF的瓷片电容.
At 115/230Vac 25℃ input and output Min and Max.Load,the ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and Parallel 47uF/0.1uF,crossed connected at testing point.
电压 最大纹波/最大噪音
Voltage Ripple and Noise(Max.)
+5Vdc 50mV p-p
3.4启动延迟时间/Turn on delay time:
当输入115Vac和输出最大负载时,最大启动时间为3S.
3Second Max.at 115Vac input and output Max.load.
3.5上升时间/Rise time:
当输入115Vac和输出最大负载时最大时间为40 mS.
40 mS Max.at 115Vac input and output Max load.
3.6保持时间/Hold up time:
当输入115Vac 和输出最大负载时,最小保持时间为5 mS .
5 mS Min.at 115Vac input and output Max.Load.
3.7过冲/Overshoot:
在电源开启或关闭的时候,最大15%.
15% Max.When power supply at turn or turn off.
4、保护功能/PROTECTION FUNCTION:
4.1短路电路保护/Short circuit protection:
该电源供给器在短路解除时能正常工作恢复.
The power supply will be auto recovered when short circuit faults remove.
4.2过流保护/Over current Protection:
过流故障排除后,电源将自动恢复正常工作.
The power supply will be auto recovered when over current faults remove.
5、环境要求/ENVIRONMENTAL REQUIREMET:
5.1 工作温度/Operating Temperature:
0℃-40℃,满载,正常工作.
0℃ to 40℃,Full load, Normal operation.
5.2 储藏温度/Storage Temperature:-20℃ to 60℃
带外壳/With package
5.3工作湿度/Relative Humidity:
5%(0℃)~90%(40℃),72小时,满载,正常工作.
5%(0℃)~90%(40℃)RH,72Hrs,Full load, Normal operating.
5.4 振动/Vibration:
1. 测试标准:国际电工电子委员会
Operating: IEC 721-3-3 3M3
5~9Hz,A=1.5mm
加速度(9~200Hz,Acceleration 5m/S2)
2. 运输/Transportation:
IEC 721-3-2 2M2
5-9Hz,A=3.5mm
9~200Hz,加速度Acceleration=5m/S2
200~500Hz,加速度Acceleration=15m/S2
3. 轴向振动/Axes,10 cycles per axis.
在测试过程中不能出现永久性的损坏.
No permanent damage may occur during testing.
在电源开启和关闭后,样机能够恢复到最初条件.
The SAMPLE has to restore to its original situation after power off/on..
5.5 跌落试验/Dropping Packed:
插墙式跌落高度为1米、桌面式跌落高度为760mm、6个面各跌一次
1M for wallmount type and 760mm for desktop type as above described，6 surfaces or one
测试台面是厚13mm的夹木板，离地面高19-20mm
The horizontal surface Consists of hardwood at least 13mm thick,mounted on two layers of plywood
each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor.
6、安全及要求/SAFETY REQUIREMENT:
6.2 高压/DIELECTRIC STRENGTH Hi-Pot:
初级对次级/Primary to secondary:3000Vac/5mA/60S or 4242Vdc/5mA/60S for type test.
（批量生产时/Batch production：3300Vac/5mA/3S）
6.3 绝缘抗阻/Iusulation resistance:
初级对次级/Primary to secondary:10MΩ min at 500V DC.
7、 结构参数/MECHANICAL REQUIREMENT: (单位：mm)
7.1 外壳/Enclosure:
外壳尺寸: L73x W41x H24mm;
The power supply size:L73x W41x H24mm;
7.2 输入线/Input Connector:
2 Pin EU插脚/Two pin input plug of EU.
8、线材/CORD: (单位：mm)
根据客户要求/ According to the customer request
9、铭牌/LABEL: (单位：mm)镭射 灰色字
