供应EC12S旋转式编码器.增量式数字电位器,调音直脚插板编码器
深圳市祺泰达电子有限公司
中国 深圳
产品属性
图文详情
品牌推荐
品牌
其他
型号
EC120
类型
旋转编码器
读出方式
接触式
工作原理
增量式
视频输入路数
24
音频输入路数
24
视频压缩格式
24
视频编码分辨率
12
网络接口
插板
| 推动开关部分 Push Switch Portion | ||||||||||||||||||
| 备注:以下规格适用于EC11编码带开关系列. | ||||||||||||||||||
| No:The following specification is only suitable for the one type with construction of EC11 encoder series. | ||||||||||||||||||
| 1.额定值 Rating | ||||||||||||||||||
| 1.1额定电压 | ||||||||||||||||||
| Rated voltage: DC 5V | ||||||||||||||||||
| 1.2最大额定电流(阻抗负载) | ||||||||||||||||||
| Maximum operating current(resistive load):10mA MAX. | ||||||||||||||||||
| 2.电气性能 Electrical Characteristics | ||||||||||||||||||
| 项目 ITEM | 条件 CONDITIONS | 规格 SPECICATIONS | ||||||||||||||||
| 2.1接触电阻 Contact resistance | 用DC 5V 10mA电压测定 | 100mΩ or less | ||||||||||||||||
| Voltage test at DC 5V 10mA. | ≤100mΩ | |||||||||||||||||
| 2.2绝缘阻抗 Insulation resistance | 在端子和安装板间施加电压250V DC. | |||||||||||||||||
| Measurement shall be made under the condition which a voltage of | 100MΩ以上 | |||||||||||||||||
| 250V DC is applied between inpidual terminals and bushing. | 100MΩ Min | |||||||||||||||||
| and bushing and plank. | ||||||||||||||||||
| 2.3振荡 Bouncing | 以1秒钟1往返(OFF-ON-OFF)按压动作. | 10ms or less | ||||||||||||||||
| Shaft shall be push at 1 cycles/s(OFF-ON-OFF). | ≤10ms | |||||||||||||||||
| 2.4耐电压 Dielectric strength | 在端子和安装板间施加AC300V 电压1分钟 | 不得有绝缘破坏 | ||||||||||||||||
| A voltage of 300V AC shall be applied for 1 minute between inpidual | Without arcing or breakdown | |||||||||||||||||
| terminals and bushing and plank. | ||||||||||||||||||
| 3.机械性能 Mechanical characteristics | ||||||||||||||||||
| 3.1开关电路.接点数 Switch circuit and number of pulse | 单极单投(按压ON) | |||||||||||||||||
| Single pole and single throw | ||||||||||||||||||
| (PUSH ON) | ||||||||||||||||||
| 3.2开关动作力 Operation fore of switch | 在轴端,沿轴向施加的按压力. | 200~800gf.cm | ||||||||||||||||
| Push static load to the shaft in the axial direction | ||||||||||||||||||
| 3.3开关动移动量 Travel of switch | 0.5(+0/-0.30)mm | |||||||||||||||||
| 4.耐久性能 Endurance Characteristics | ||||||||||||||||||
| 按压寿命 push life | The shaft of encoder shall be push to 20000 cycles at a speed of | 接触电阻:≤200mΩ | ||||||||||||||||
| 600 cycles/H without electrical load,after with measurements | 其它应满足初期规格. | |||||||||||||||||
| shall be made | Contact resistance:200mΩ or less | |||||||||||||||||
| 在无负荷条件下轴以600次/小时速度按压往返20000周. | Specifi cation in clause shall be satisfied | |||||||||||||||||
