滚筒清洗机的工作原理：间歇操作的滚筒式清洗机两端加有挡板，周向开有带盖板的进出料口。料口向上时，可打开料口盖板向里加料；洗净后，筒体转至料口朝下，打开盖板便可卸料。为便于物料在筒内翻 滚，加料不可太满。一般这种清洗机采用喷水管连续或间歇地向筒内喷水以便使污物浸润而迅速剥离和排走。连续式滚筒清洗机的滚筒两端为开口式，原料从一端进入，另一端排出。物料在筒内的轴向运动，可以通过使筒倾斜安装，也可通过在筒体内壁设置螺线导板或抄板的方式实现。为提高清洗效果，有的滚筒式清洗机内安装了可上下、左右调节的毛刷。
The working principle of the drum washing machine drum type washing machine: both ends of intermittent operation with a baffle, Zhou Xiangkai has inlet and outlet with a cover plate mouth. Feed opening up, open the inlet cover plate to feed; after washing, the cylinder to the feeding mouth down, open the cover can discharge. In order to facilitate the materials in the barrel varus roll, feeding should not be too full. This washing machine adopts a spray pipe continuously or intermittently into the cylinder of water so that the dirt infiltration and rapid stripping and drain away. Both ends of the roller continuous roller cleaning machine is open, the raw material from one end to the other end, discharge. Axial movement of the material in the barrel, the barrel can be inclined installation, can also be achieved through the spiral guide or copy board is arranged on the inner wall of the barrel body way. In order to improve the cleaning effect, some drum type washing machine has been installed in the up and down, the hair brush.
滚筒清洗机的应用：物料由进料斗进入落到滚筒内，随滚筒的转动而在滚筒内不断翻滚相互摩擦，再加上喷淋水的冲洗，使物料表面的污垢和泥砂脱落，由滚筒的筛网洞孔随喷淋水经排水斗排出。由进料口进入清洗槽内的原料，首先在两个转动刷辊产生的涡流中得以清洗，同时，由于两个刷辊间隙较窄，故其间的水流有较高流速从而该压力降低，被清洗物料在压力差和刷辊摩擦作用下通过刷辊,进一步得到刷洗。而后，被清洗物料在出料翻斗中又经高压水得到进一步喷淋清洗。
Application of drum washing machine: material consists of feed hopper into into the drum, the drum rotation in the drum roll continuously mutual friction, coupled with the flushing spray water, so the material surface dirt and mud and sand falling holes, composed of a screen drum with spray water drainage hopper discharge. From the inlet into the cleaning groove of the raw materials, the first to be cleaned, the two rotating brush roll eddy current at the same time, because the two brush roller clearance is narrow, so the water has higher velocity and the pressure is reduced, cleaning materials through the brush roller brush roller pressure and friction effect further out. Then, by cleaning the material in the material bucket and the high pressure water further cleaning spray.
滚筒清洗机的特性：由给瓶端进入机器的瓶子，先后经过预冲洗、预浸泡、洗涤剂浸泡、洗涤剂喷射、热水预喷、热水喷射、温水喷射和冷水喷射等清洗作用，最后从出瓶端离开洗瓶机。预冲洗是为了将瓶子外附着的污垢除去，以降低后面洗涤液消耗量。洗液喷洗区位于洗液浸泡槽上方，这样从瓶中沥下的洗液又回到液洗槽。消毒后的空罐最后由第三个星形轮送到出罐轨道进入装罐工序。空罐在清洗机中回转时有一定的倾斜，因此可使罐内的水流出。污水由排水管排入下水道。
Characteristic of cylinder washing machine is composed of bottle machine: to end into the bottle, after pre washing, pre soaking, soaking, detergent, detergent spray hot water spray, water injection, water injection and water injection cleaning effect, leave the bottle washing machine and finally from the bottle end. Pre washing is to remove dirt attached to the bottle, in order to reduce the back washing fluid consumption. Lotion spray washing area is located above the soaking liquid from a bottle, so Li under the back washing bath lotion. Empty tank after disinfection finally by third star wheel to a tank track into the canning process. Empty cans in cleaning machine rotates a certain inclination, thus can make the tank water flows. The sewage from the drainage tube into the sewer.
