名尊泡沫填缝剂建议用于建筑工程，特别是门窗的安装。它卓越的保温性能保证了节能，高度粘结及弹性保证了坚固及防水的密封。本产品是半硬质的闭孔泡沫体，泡沫喷出后体积迅速膨胀，可依缝隙、空洞的形状自由涨满，固化快、发泡体积大，延长米长。本产品建议在相对湿度高于60%的地方使用。
使用范围：
门，窗框的填充及安装；裂缝和缺洞的填充。防尘、防害虫，防空气滤渗的密封；空调、排风扇的漏洞填缝；管道和下水道的密封；隔热、隔音；电器开关盒的安装定位及绝缘；浴缸，电线出口 裂缝的填充；各种非标易碎物品的防震包装；屋顶裂缝的填补；防水与保温；堵各种害虫唾咬之功能； 堵防老鼠进入管道，孔洞等
APPLICATION AREA:
gate,window frame packing and installment;crack and lack hole packing;dustproof,against harmful insect,against air infiltration's seal;air conditioning,platoon wind the fan's crack sealing;pipeline and sewer's sea;heat insulation,the sound-insulated;electric appliance switch-box's installment locates and insulates;the bathtub electric wire exports the crack packing;each kind of non-sign brittle goods quakeproof packing;roof the crack fill;waterpoofing and heat preservation;stops up each kind of harmful insect saliva to nip function;to stop up against mouse access duct,hole and so on
产品特性：
施工温度；料罐：+10℃- +30℃
环境：+5℃- +30℃ 发泡倍数：78倍
最佳施工温度：18℃to+25℃
固化后耐温范围：-40℃to+90℃
表干时间：10-14分钟；可切割时间：30-40分钟
此数据为实验室条件下测试所得23℃。50%相对湿度
贮存：
未开封时请把本产品保存在+10℃到+30℃的干燥场所，禁止靠近明火或者与易燃易爆物品接触
CHARACTERISTIC OF PRODUCTS
feed tank：+10℃-+30℃
Environment：+5℃-+30℃foam multiples：78times.
the best construction temperature：18℃to +25℃.
Curing temperature range：-40℃to +90℃.Dry Time 10 to
14 minutes Cutting Time 30-40 minutes This test data
obtained under laboratory conditions 23℃.50%RH
STORAGE
Please put this product without Kaifeng preserved in the +10℃
to + 30℃dry places. Prohibited near open flame or and
inflammable and explosive materials contact.
使用方法：
1.施工前，去除施工表面的浮灰、油污、并在施工表面喷少许水.
2.将料罐上下摇匀几次，将料罐倒置并旋转固定于喷枪连接口.
3.使用时将料罐倒置，由下而上地喷出泡沫，一般情况只需填满接缝的70-90%（泡沫将略微膨胀装）
4.十分钟后表面开始固化，静待约40分钟即可去除泡沫多余部分
5.本产品不抗紫外线，因此推荐在固化的泡沫表面用其他材料的涂装，例如：水泥砂浆、涂料等（施工后24小时才可涂装）
PRODUCTS APPLICATION
1.pre-construction,construction of the surface to remove floating dust,oil.andspray a little water in the surface construction.
2.cans will be expected to shake up and down several times.Material can be fixed on the gun upside down and rotate the connector.
3.material can be used upside down.Spray foam from the buttom up,in general,only 70-90% filled joints（slightly inflated the bubble will install）
4.Ten minutes after the start curing the suface,wait about 40minutes to remove excess foam.
5.This product in not UV,it is recommended in the curing of the foam surface coating with other materials,such as:cement,mortal,paint,etc.（24 hours to paint the construction）.
安全建议：
产品固化后对人体没有危害。施工请穿戴防护手套、衣服、口罩和护目镜。施工现场必须具备通风条件。本产品可能引起眼睛，呼吸系统，皮肤不适。不慎吸入后或触及皮肤会引起刺激症状。禁止靠近明火或与易燃易爆物品接触，禁止吸烟。请勿吸入挥发气体。万一吞下请立即送院就医。不慎吸入后有刺激症状时应立即转移到新鲜空气处并就医。避免阳光直射，置于阴凉干燥处，且温度不超过50℃。使用后禁止燃烧或刺穿空罐。请将涂料放在儿童触及不到的地方。
Safety recommendations:
The product after curing, no harm to the human body. Construction please wear protective gloves, clothing,masks and goggles. The construction site must be ventilated. This product may cause eye, respiratory system,skin discomfort. Accidentally inhalation or skin contact may cause irritation symptoms. Prohibit near open flame or contact with flammable and explosive articles, no smoking. Do not inhale vapors. If swallowed immediately sent to hospital. The inadvertent inhalation after stimulation symptoms should be immediately transferred to the fresh air and see the doctor. Avoid direct sunlight, in a cool and dry place, and the temperature does not exceed 50℃. After the use of prohibited burning or piercing empty cans. Please put paint on the place where children can not reach
