不是所有的江苏NSK轴承要求最小的工作游隙。你必须根据情况选择合适的间隙。在GB，滚动轴承的径向游隙分为五组：P2，P0，P3，P4和P5。间隙值从大到小，且0组是标准的差距。
Not all of the requirements of Jiangsu NSK bearing minimum working clearance. You must select the appropriate clearance according to the situation. In GB, the radial clearance of rolling bearings are pided into five groups: group second, group third, zero group, fourth group and 5 group. The gap value from large to small, and the 0 group is a standard gap.
基本径向游隙组适用于一般工况下，正常温度和正常盈。滚动轴承的特殊条件，如高温、高速、低噪声下工作，低摩擦等特殊条件下大的径向间隙的选择是合适的；对江苏NSK轴承机床主轴和主轴轴承应选用较小的径向间隙量CE、R辊轴和轴承。辊轴是适用于辊轴。保持一个小的差距在你的工作。
The basic radial clearance for general condition, normal temperature and normal profit. The special conditions of rolling bearings, such as high temperature, high speed, low noise, low friction and other special conditions, are suitable for the selection of large radial clearance. The smaller radial clearance CE, R roll shaft and bearing should be selected for the spindle and spindle bearing of the NSK bearing machine tool. The roller is applied to roller shaft. Keep a small gap in your work.
此外，隔震支座没有间隙，与江苏NSK轴承的最终间隙小于安装前的原始游隙，由于轴承承受一定的负荷，在三月旋转产生弹性变形。江苏SKF轴承NG和负载。
In addition, the isolation bearing has no clearance, and the final clearance of the Jiangsu NSK bearing is less than the original clearance before the installation. Because the bearing bears a certain load, it rotates in March to produce elastic deformation. Jiangsu SKF bearing NG and load.
安装江苏NSK轴承后，检查作业，检查安装是否正确。小型机械可以手动旋转确认是否转动灵活。由于异物、疤痕、凹陷等原因，检查项目运行不佳。由于安装不良，由于小的安装空间，安装误差大，摩擦扭矩过大，安装基座的扭矩不稳定。
Jiangsu NSK bearing installation inspection work, and check whether the installation is correct. Small machinery can confirm whether the manual rotation of flexible rotation. Due to a foreign body, scar, depression, poor operation of inspection items. Due to improper installation, the installation space is small, installation error, friction torque is too large, the mounting base of torque instability.
如果没有异常，可以启动电源操作。电力开始慢慢从空载慢慢增加到额定操作条件下。检测项目包括异常的声音，在江苏NSK轴承温度的变化、润滑剂的泄漏或变色。如有异常，立即停止操作，检查机械和轴承的ISP。如果有必要，应该拆除。
If there is no exception, you can start the power supply operation. The power began to slowly increase from no-load to the rated operating conditions. The test items included abnormal sound, changes in Jiangsu, NSK bearing temperature of the lubricant leakage or discoloration. If abnormal, immediately stop the operation, check the mechanical and bearing ISP. If necessary, should be removed.
江苏NSK轴承温度一般可以从轴承箱外部温度的推导。但更准确的利用油孔的轴承外圈温度的直接测量。滚动轴承的温度逐渐增加的操作，通常在一个稳定的一~ 2小时温度。
Jiangsu NSK bearing temperature can be inferred from the external temperature of the bearing box. But the use of direct measurement of the bearing outer ring temperature oil hole more accurate. Rolling bearing temperature gradually increased, usually in a 2 hour temperature stable.
如果江苏NSK轴承是错位的，温度会急剧上升，会出现异常高温。原因是，有太多的润滑油。江苏NSK轴承游隙过小、安装不当，密封装置摩擦过大。考察轴承的旋转音用听诊器等。它具有较强的金属噪音，声音异常，不规则的声音。原因是润滑不良，轴或轴承座精度差，轴承损坏和异物入侵。
If Jiangsu NSK bearing is misplaced, the temperature will rise sharply, there will be abnormal high temperature. The reason is that there is too much lubrication. Jiangsu NSK bearing clearance is too small, improper installation, high friction sealing device. Study of bearing rotary voice with a stethoscope. It has strong metal noise, abnormal sound and irregular sound. Due to bad lubrication, shaft or bearing precision, bearing damage and foreign invasion.
文章来自：江苏SKF轴承 www.wh-skf.com
The article comes from: Jiangsu SKF bearing www.wh-skf.com
文章来自：江苏INA轴承 www.ina-china.cn
The article comes from: Jiangsu INA bearing www.ina-china.cn
文章来自：江苏NSK轴承 www.klbbearings.com
The article comes from: Jiangsu NSK bearing www.klbbearings.com
