扬州NSK轴承的温度通常可以从轴承外部的温度推断出来。如果油孔能够直接测量轴承外圈的温度，则更为合适。
The temperature of NSK bearings in Yangzhou can usually be deduced from the temperature on the outside of the bearing. If the oil hole can directly measure the temperature of the outer ring of the bearing, it is more appropriate.
通常，扬州NSK轴承的温度随着轴承的起动而缓慢上升，1-2小时后达到稳定状态。扬州NSK轴承的正常温度不同于机器的热容量、散热、速度和负载。如果润滑和安装部件合适，轴承温度将迅速升高，并且会出现异常高温。此时，必须停止手术，并采取必要的预防措施。
Usually, the temperature of NSK bearing in Yangzhou increases slowly with the starting of bearings, and it reaches a stable state after 1-2 hours. The normal temperature of NSK bearings in Yangzhou is different from the heat capacity, heat dissipation, speed and load of the machine. If the lubrication and installation parts are suitable, the bearing temperature will rise rapidly and there will be an abnormal high temperature. At this point, surgery must be stopped and necessary precautions should be taken.
热传感器的使用可以随时监测扬州NSK轴承的工作温度。当温度超过规定值时，可自动报警或停止燃烧轴事故。
The use of thermal sensors can monitor the working temperature of NSK bearings at any time in Yangzhou. When the temperature exceeds the specified value, it can automatically alarm or stop the burning shaft accident.
高温的使用常常表明它处于不正常的状态。高温对扬州NSK轴承的润滑剂也是有害的。有时轴承过热可归因于轴承的润滑剂。如果轴承温度超过125度，长期转移将降低轴承寿命。高温扬州NSK轴承的原因包括润滑不足或过度润滑，润滑剂。它含有杂质、过载、轴承损坏环、间隙不足和油封引起的高摩擦。
The use of high temperature often indicates that it is in an abnormal state. High temperature is also harmful to the lubricant of NSK bearing in Yangzhou. Sometimes the bearing overheat can be attributed to the lubricant of the bearing. If the bearing temperature exceeds 125 degrees, the long term transfer will reduce the bearing life. The reasons for high temperature Yangzhou NSK bearings include inadequate lubrication or excessive lubrication, lubricants. It contains impurities, overload, bearing damage ring, insufficient clearance and high friction caused by oil seal.
因此，扬州NSK轴承温度的连续监测是必要的，不管轴承本身或其他重要部件。如果操作条件保持不变，温度的任何变化都可以指示故障。
Therefore, the continuous monitoring of NSK bearing temperature in Yangzhou is necessary, regardless of the bearing itself or other important components. If the operating conditions remain unchanged, any change in temperature can indicate failure.
扬州NSK轴承温度的周期性测量可用于诸如数字温度计的温度计，该温度计能够精确测量轴承温度并在单位温度或华氏温度下显示轴承温度。
The periodic measurement of the Yangzhou NSK bearing temperature can be used for a thermometer, such as a digital thermometer. The thermometer can accurately measure the bearing temperature and display the bearing temperature at unit temperature or Fahrenheit temperature.
剥落深度相对较浅，一般只有几微米或小于1米（有些文件称为20微米）。通常，经过扬州NSK轴承数以百万计的转数或数以百万计的转弯，直线轴承就会脱落。在大多数情况下，这种类型的剥落类型不损害一般用途（即，没有特别的使用要求），但是对于高精度和高速轴承，不允许剥离。扬州NSK轴承
The spalling depth is relatively shallow, generally only a few microns or less than 1 meters (some documents are called 20 microns). Usually, after the millions of revolutions or millions of turns of NSK bearings in Yangzhou, the linear bearings will fall off. In most cases, this type of exfoliation type does not damage the general use (i.e., no special use requirements), but for high precision and high speed bearings, dissection is not allowed. Yangzhou NSK bearing
此时，需要控制加热温度。一般来说，轴承被加热到80摄氏度，最高温度是100度。超过120摄氏度将导致轴承的回火现象，导致硬度的降低和环精度的降低。
At this point, the heating temperature needs to be controlled. Generally speaking, the bearing is heated to 80 degrees Celsius and the highest temperature is 100 degrees. More than 120 degrees Celsius will cause the bearing's tempering phenomenon, resulting in the reduction of hardness and the reduction of ring accuracy.
这种方法是将轴承放置在一个温度为100摄氏度的电热板上的最方便的方法。
This method is the most convenient way to place the bearing on an electric heating plate with a temperature of 100 degrees Celsius.
直线轴承在闭式自动控温电炉中加热，加热均匀。温度控制准确，加热速度快，适用于多个轴承的间歇加热。
The linear bearing is heated in the closed automatic temperature control electric furnace, and the heating is uniform. The temperature control is accurate and the heating speed is fast, which is suitable for intermittent heating of multiple bearings.
文章来自：扬州SKF轴承 www.wh-skf.com
The article comes from: Yangzhou SKF bearing www.wh-skf.com
文章来自：扬州INA轴承 www.ina-china.cn
The article comes from: Yangzhou INA bearing www.ina-china.cn
文章来自：扬州NSK轴承 www.klbbearings.com
The article comes from: Yangzhou NSK bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672
