天津市北辰区机笔记本全自动YO单/双线圈装订机厂家电话价格报价
东莞市恒博装订设备有限公司
中国 东莞
产品属性
图文详情
品牌推荐
品牌
aft
型号
aft366
类型
铁圈装订机
操作方式
全自动
加工定制
是
装订厚度
50mm
最大装订纸张
520*630
最小装订纸张
100*100
最大装订厚度
12
装订能力
1200
工作速度
1200
产地
东莞
材质
金属
主机功率
3KW
工作电压
380V
外形尺寸
800*1200*3200mm
重量
500kg
天津市 和平区 北辰区 河北区 河西区 西青区 津南区 东丽区 武清区 宝坻区 红桥区 大港区 汉沽区 静海县 宁河县 塘沽区 蓟县 南开区 河东区
六、台历 挂历 笔记本全自动YO单/双线圈装订机的操作及更换零部件折卸方法 Testing and running
1．安全操作注意事项 Notice of safety operate
1.1 操作机器以前，必须仔细阅读本机器说明书。
Before operating the machine, you must read the machine manual carefully.
1.2 了解台历 挂历 笔记本全自动YO单/双线圈装订机各部分的作用和潜在危险区域，知道必要的安全措施。
Understand the role of the various parts of the machine and potentially dangerous areas, and know the necessary safety measures
1.3 启动台历 挂历 笔记本全自动YO单/双线圈装订机前，检查机器各手柄，按钮是否处于预定的工作位置。
Before starting the machine, check the handle of the machine and whether the button is in the intended working position.
1.4 如果台历 挂历 笔记本全自动YO单/双线圈装订机工作时突然停止，不要马上重新启动，应该按下“总停”自锁按钮，检查停机原因，待故障排除后方可重新启动。 If the machine suddenly stops working, do not restart immediately, you should press the "total stop" self-locking button, check the cause of the shutdown, to be troubleshooting before you can restart.
1.5 不允许在机器运转时，维护运动零部件和靠近运动零部件的其他零部件。 It is not permissible to maintain moving parts and other parts near moving parts while the machine is running.
1.6 大面积保养或修理时，必须按下“停止”自锁按钮，切断所以电源、气源。Large area maintenance or repair, you must press the "stop" self-locking button, cut off the power supply, gas source.
1.7 在进行调整、保养和修理工作时，不得使用不适当的工具。工作完毕后必须清理检查机器上的工具和其他杂物，以免发生故障。 Undue tools should not be used for adjustment, maintenance and repair work. After the work must be cleaned to check the tools and other debris on the machine, so as to avoid failure.
1.8 在重新启动机器前，应检查所有安全设施是否处在正常位置，是否紧定，注意机器周围的其他人员是否处在安全的位置。 Before restarting the machine, check that all safety devices are in their normal position, are they tightened, and that the rest of the machine is in a safe place.
1.9 保持机器和周围环境的清洁，及时清除掉落在地板上的油污，清理工作区的工具、抹布及碎纸废料等。 Keep the machine and the surrounding environment clean, remove the oil on the floor in a timely manner, clean up the work area of the tools, rags and shredded scrap.
1.10 及时维护、更换已失效和损坏的装置，及时报告机器发生的问题。Timely maintenance, replacement of failure and damage to the device, the timely report of the machine problems.
2．台历 挂历 笔记本全自动YO单/双线圈装订机收放物料装置的调整 Adjust the feed and receive belt
2.1 台历 挂历 笔记本全自动YO单/双线圈装订机上料装置的调整 Adjust the feed belt
该工位可根据产品的宽窄来调节输送料道的宽度，参考（图九）松开护罩1的固定螺丝123，然后根据产品的需要调整料道的宽窄。The position of the station can be adjusted according to the width of the product to adjust the width of the conveyor material, refer to (Picture 9) to release the cover screw 1 123, and then adjust the width of the material according to the needs of the material.
收料装置的调整(参考图三) Adjust the receive belt (Picture 3)
该工位主要是配合主机完成收料工作，可根据主机的装订速度自动调整线体的每次位移. The station is mainly with the host to complete the receipt work, according to the host&＃39;s binding speed automatically adjust the line of each displacement.
3. 台历 挂历 笔记本全自动YO单/双线圈装订机推刀调试 Test push knife
根据产品大小的需要，可通过调节推刀组的固定螺丝的安装位置来调节T的宽度（见图十）Depending on the size of the product, the width of the T can be adjusted by adjusting the mounting position of the setscrews&＃39; fixing screws (Picture 10)
4.台历 挂历 笔记本全自动YO单/双线圈装订机孔位自动校正系统的调整 Adjust the corrective system
此工位主要是通过整形针来实现孔位校正的，根据产品的需要可调整整形针间的间距和角度。。This position is mainly through the pins to achieve hole correction, according to the needs of the product can adjust the space between the needle and angle.
六、台历 挂历 笔记本全自动YO单/双线圈装订机的操作及更换零部件折卸方法 Testing and running
1．安全操作注意事项 Notice of safety operate
1.1 操作机器以前，必须仔细阅读本机器说明书。
Before operating the machine, you must read the machine manual carefully.
1.2 了解台历 挂历 笔记本全自动YO单/双线圈装订机各部分的作用和潜在危险区域，知道必要的安全措施。
Understand the role of the various parts of the machine and potentially dangerous areas, and know the necessary safety measures
1.3 启动台历 挂历 笔记本全自动YO单/双线圈装订机前，检查机器各手柄，按钮是否处于预定的工作位置。
Before starting the machine, check the handle of the machine and whether the button is in the intended working position.
1.4 如果台历 挂历 笔记本全自动YO单/双线圈装订机工作时突然停止，不要马上重新启动，应该按下“总停”自锁按钮，检查停机原因，待故障排除后方可重新启动。 If the machine suddenly stops working, do not restart immediately, you should press the "total stop" self-locking button, check the cause of the shutdown, to be troubleshooting before you can restart.
1.5 不允许在机器运转时，维护运动零部件和靠近运动零部件的其他零部件。 It is not permissible to maintain moving parts and other parts near moving parts while the machine is running.
1.6 大面积保养或修理时，必须按下“停止”自锁按钮，切断所以电源、气源。Large area maintenance or repair, you must press the "stop" self-locking button, cut off the power supply, gas source.
1.7 在进行调整、保养和修理工作时，不得使用不适当的工具。工作完毕后必须清理检查机器上的工具和其他杂物，以免发生故障。 Undue tools should not be used for adjustment, maintenance and repair work. After the work must be cleaned to check the tools and other debris on the machine, so as to avoid failure.
1.8 在重新启动机器前，应检查所有安全设施是否处在正常位置，是否紧定，注意机器周围的其他人员是否处在安全的位置。 Before restarting the machine, check that all safety devices are in their normal position, are they tightened, and that the rest of the machine is in a safe place.
1.9 保持机器和周围环境的清洁，及时清除掉落在地板上的油污，清理工作区的工具、抹布及碎纸废料等。 Keep the machine and the surrounding environment clean, remove the oil on the floor in a timely manner, clean up the work area of the tools, rags and shredded scrap.
1.10 及时维护、更换已失效和损坏的装置，及时报告机器发生的问题。Timely maintenance, replacement of failure and damage to the device, the timely report of the machine problems.
2．台历 挂历 笔记本全自动YO单/双线圈装订机收放物料装置的调整 Adjust the feed and receive belt
2.1 台历 挂历 笔记本全自动YO单/双线圈装订机上料装置的调整 Adjust the feed belt
该工位可根据产品的宽窄来调节输送料道的宽度，参考（图九）松开护罩1的固定螺丝123，然后根据产品的需要调整料道的宽窄。The position of the station can be adjusted according to the width of the product to adjust the width of the conveyor material, refer to (Picture 9) to release the cover screw 1 123, and then adjust the width of the material according to the needs of the material.
收料装置的调整(参考图三) Adjust the receive belt (Picture 3)
该工位主要是配合主机完成收料工作，可根据主机的装订速度自动调整线体的每次位移. The station is mainly with the host to complete the receipt work, according to the host&＃39;s binding speed automatically adjust the line of each displacement.
3. 台历 挂历 笔记本全自动YO单/双线圈装订机推刀调试 Test push knife
根据产品大小的需要，可通过调节推刀组的固定螺丝的安装位置来调节T的宽度（见图十）Depending on the size of the product, the width of the T can be adjusted by adjusting the mounting position of the setscrews&＃39; fixing screws (Picture 10)
4.台历 挂历 笔记本全自动YO单/双线圈装订机孔位自动校正系统的调整 Adjust the corrective system
此工位主要是通过整形针来实现孔位校正的，根据产品的需要可调整整形针间的间距和角度。。This position is mainly through the pins to achieve hole correction, according to the needs of the product can adjust the space between the needle and angle.
