Fann 209506 175ml高温高压失水仪加热套HPHT压滤机配件
天厦（厦门）国际贸易有限公司
中国 厦门
产品属性
图文详情
品牌推荐
品牌
FANN
型号
209506
类型
高温高压
测量范围
111m
最小显示分辨率
222mm
测量精度
333%
电源
444
工作温度
555℃
外形尺寸
666mm
重量
777kg
品牌
FANN
型号
209506
产地
美国
类型
高温高压失水仪
品类
压滤机配件
美国Fann 209506 175ml高温高压失水仪加热套HPHT压滤机配件
Cell assemblies include the CellTell? Positive Pressure Indicator on the top of the cell assembly to show when the cell is pressurized. This is a safety device that provides additional protection in case the normal pressure bleeding procedure does not operate due to plugging or other reasons. If this indicator can be depressed and will stay depressed, the cell does not have pressure in it, and it is safe to open. If the indicator cannot be depressed or will not stay depressed, the cell has pressure in it and MUST NOT be disassembled. The CellTell? indicator is installed in the solid end of single-ended cells and in the top cap of double-ended cells.
电池组件包括CellTell?积极压力指示器的顶端细胞组装指当细胞加压。这是一种安全装置，在正常压力下，由于堵塞或其他原因导致出油过程无法进行时，提供额外的保护。如果这个指示器可以被压下并将保持压下状态，则细胞内没有压力，可以安全地打开。如果指示器不能被压下或不保持压下状态，则电池内有压力，不能拆卸。的CellTell?指示器安装在稳固的单端细胞和双头的顶盖细胞。
Caution should be exercised by all personnel working with or working in the area where HPHT Filter Presses are in operation to avoid accidental injury caused by touching the heating jacket or cell assembly while these are hot. The heating jacket can operate at a temperature that will cause burns if touched. Safeguard the equipment after the test ends long enough for it to cool. It can still cause burns even after it has been turned off.
所有在HPHT压滤机工作的人员或在HPHT压滤机工作的区域内工作的人员都应注意，避免在加热夹套或电池组件处于热状态时碰触造成意外伤害。加热夹套的工作温度可达到接触后会灼伤的温度。在测试结束后保护设备足够长的时间使其冷却。即使关掉它，它仍然会引起烧伤。
The practice of removing the cell and cooling it under water is very dangerous and is not recommended because the user could be severely burned if the cell is touched or accidentally dropped. Hot steam generated when the water hits the hot cell can cause severe burns. Use extreme caution when handling a hot cell. A cell removal tool, shown in Figure 5-4, is available for handling the cell assembly and removing it from the heating jacket. Its use will reduce the chances of accidentally dropping the cell or being burned by it.
将电池取出并在水下冷却的做法是非常危险的，不建议这样做，因为如果电池被触摸或意外掉落，用户可能会严重烧伤。当水冲击热电池时产生的热蒸汽会导致严重烧伤。在处理热电池时要特别小心。可以使用如图5-4所示的电池拆卸工具来处理电池组件并将其从加热夹套上拆卸下来。它的使用将减少不小心掉下电池或被它烧伤的机会。
82839536 比重计 OFI 115-00
83107124 加热套 Fann 206966
82651450 500ml高温高压失水仪样品杯 Fann 209570
82651457 175ml高温高压失水仪样品杯 Fann 209569
83107123 175ml高温高压失水仪加热套 Fann 209506
83107123 500ml高温高压失水仪加热套 Fann 209541
81972339 滚子炉老化罐 OFI 175-50
81490030 老化罐杯体内聚四氟O型圈 OFI 175-09-1
81490030 老化罐杯体外部O型圈 OFI 175-46
81972341 直径3/8英寸固定螺钉 OFI 175-14
81972340 阀杆 OFI 175-16
The HPHT Filter Press consists of a stainless steel cell with filtering area of 3.5 in2 (22.58 cm 2 ), an aluminum heating jacket, filter medium, graduated cylinder to collect filtrate and pressurization equipment. The CellTell? Positive Pressure Indicator is safety feature that is also included. Filter media choices are API standard filter paper, ceramic discs of various porosities, and screens of various mesh sizes. For operation above 375°F (190°C), the filter paper should be backed with a glass fiber filter. One alternative is a stainless steel filter. Another alternative is the use of a cell adapted to accept a ceramic filter disc. HPHT filter presses are available in two cell capacity sizes, 175 ml and 500 ml, as shown in Figures 3-1 and 3-2, respectively. Both series are available with either 115 volt AC or 230 volt AC heating jackets. See Table 3-1 for features and specifications and Figures 3-1 and 3-2.美国Fann 209506 175ml高温高压失水仪加热套HPHT压滤机配件
HPHT压滤机由一个过滤面积为3.5 in2 (22.58 cm 2)的不锈钢滤室、一个铝制加热夹套、过滤介质、刻度筒组成，用于收集滤液和加压设备。积极压力指示器的CellTell?是安全功能,也包括在内。过滤介质选择有API标准滤纸、各种孔隙度的陶瓷圆盘、各种网格尺寸的筛网。操作超过375°F(190°C),应该支持与玻璃纤维滤纸过滤器。另一种选择是不锈钢过滤器。另一种选择是使用适于接受陶瓷滤片的电池。HPHT压滤机有容量175ml和500ml两种规格，如图3-1和图3-2所示。这两个系列都有115伏交流电或230伏交流电加热护套。特性和规格见表3-1，图3-1和图3-2。
Cell assemblies include the CellTell? Positive Pressure Indicator on the top of the cell assembly to show when the cell is pressurized. This is a safety device that provides additional protection in case the normal pressure bleeding procedure does not operate due to plugging or other reasons. If this indicator can be depressed and will stay depressed, the cell does not have pressure in it, and it is safe to open. If the indicator cannot be depressed or will not stay depressed, the cell has pressure in it and MUST NOT be disassembled. The CellTell? indicator is installed in the solid end of single-ended cells and in the top cap of double-ended cells.
电池组件包括CellTell?积极压力指示器的顶端细胞组装指当细胞加压。这是一种安全装置，在正常压力下，由于堵塞或其他原因导致出油过程无法进行时，提供额外的保护。如果这个指示器可以被压下并将保持压下状态，则细胞内没有压力，可以安全地打开。如果指示器不能被压下或不保持压下状态，则电池内有压力，不能拆卸。的CellTell?指示器安装在稳固的单端细胞和双头的顶盖细胞。
Caution should be exercised by all personnel working with or working in the area where HPHT Filter Presses are in operation to avoid accidental injury caused by touching the heating jacket or cell assembly while these are hot. The heating jacket can operate at a temperature that will cause burns if touched. Safeguard the equipment after the test ends long enough for it to cool. It can still cause burns even after it has been turned off.
所有在HPHT压滤机工作的人员或在HPHT压滤机工作的区域内工作的人员都应注意，避免在加热夹套或电池组件处于热状态时碰触造成意外伤害。加热夹套的工作温度可达到接触后会灼伤的温度。在测试结束后保护设备足够长的时间使其冷却。即使关掉它，它仍然会引起烧伤。
The practice of removing the cell and cooling it under water is very dangerous and is not recommended because the user could be severely burned if the cell is touched or accidentally dropped. Hot steam generated when the water hits the hot cell can cause severe burns. Use extreme caution when handling a hot cell. A cell removal tool, shown in Figure 5-4, is available for handling the cell assembly and removing it from the heating jacket. Its use will reduce the chances of accidentally dropping the cell or being burned by it.
将电池取出并在水下冷却的做法是非常危险的，不建议这样做，因为如果电池被触摸或意外掉落，用户可能会严重烧伤。当水冲击热电池时产生的热蒸汽会导致严重烧伤。在处理热电池时要特别小心。可以使用如图5-4所示的电池拆卸工具来处理电池组件并将其从加热夹套上拆卸下来。它的使用将减少不小心掉下电池或被它烧伤的机会。
82839536 比重计 OFI 115-00
83107124 加热套 Fann 206966
82651450 500ml高温高压失水仪样品杯 Fann 209570
82651457 175ml高温高压失水仪样品杯 Fann 209569
83107123 175ml高温高压失水仪加热套 Fann 209506
83107123 500ml高温高压失水仪加热套 Fann 209541
81972339 滚子炉老化罐 OFI 175-50
81490030 老化罐杯体内聚四氟O型圈 OFI 175-09-1
81490030 老化罐杯体外部O型圈 OFI 175-46
81972341 直径3/8英寸固定螺钉 OFI 175-14
81972340 阀杆 OFI 175-16
The HPHT Filter Press consists of a stainless steel cell with filtering area of 3.5 in2 (22.58 cm 2 ), an aluminum heating jacket, filter medium, graduated cylinder to collect filtrate and pressurization equipment. The CellTell? Positive Pressure Indicator is safety feature that is also included. Filter media choices are API standard filter paper, ceramic discs of various porosities, and screens of various mesh sizes. For operation above 375°F (190°C), the filter paper should be backed with a glass fiber filter. One alternative is a stainless steel filter. Another alternative is the use of a cell adapted to accept a ceramic filter disc. HPHT filter presses are available in two cell capacity sizes, 175 ml and 500 ml, as shown in Figures 3-1 and 3-2, respectively. Both series are available with either 115 volt AC or 230 volt AC heating jackets. See Table 3-1 for features and specifications and Figures 3-1 and 3-2.美国Fann 209506 175ml高温高压失水仪加热套HPHT压滤机配件
HPHT压滤机由一个过滤面积为3.5 in2 (22.58 cm 2)的不锈钢滤室、一个铝制加热夹套、过滤介质、刻度筒组成，用于收集滤液和加压设备。积极压力指示器的CellTell?是安全功能,也包括在内。过滤介质选择有API标准滤纸、各种孔隙度的陶瓷圆盘、各种网格尺寸的筛网。操作超过375°F(190°C),应该支持与玻璃纤维滤纸过滤器。另一种选择是不锈钢过滤器。另一种选择是使用适于接受陶瓷滤片的电池。HPHT压滤机有容量175ml和500ml两种规格，如图3-1和图3-2所示。这两个系列都有115伏交流电或230伏交流电加热护套。特性和规格见表3-1，图3-1和图3-2。
