KANE ACE M-577
Page 1 of 5
2016/9/21
KANEKA Corporation M-577-a01
Created September 21, 2016
Revised
Safety Data Sheet
1.CHEMICAL PRODUCT AND COMPANY INDENTIFICATION
Product name KANE ACE M-577
Supplier/Manufacture’s name KANEKA Corporation
Address
Phone number
ARK MORI BUILDING
12-32, 1-CHOME AKASAKA, MINATO-KU,
TOKYO 107-6028, JAPAN
TEL +81-3-5574-8030; FAX +81-3-5574-8128
Emergency contact High Performance Polymers Division
E-mail PPD_QA@kaneka.co.jp
Phone number +81-3-5574-8030 : Hours of operation,
Monday – Friday, 9:00 a.m. – 5:00 p.m.(JST)
Chemical family/use Impact modifier for polyester
Document number M-577-a01
2.HAZARD IDENTIFICATION
GHS classification Not classified
Other hazards
P210 Keep away from heat/sparks/open flames/hot surfaces. –No
smoking.
P241 IF dust clouds can occur: Use explosion-proof electrical/
ventilating/lighting/equipment.
P403+P233 Store in a well-ventilated place. Keep container tightly closed.
P235+P410 Keep cool. Protect from sunlight.
NFPA RATING
Health: 1, Flammability: 2, Reactivity: 0
3.COMPOSITION/INFORMATION ON INGREDIENTS
Substances/Mixtures Substances(Polymer)
Identity Concentration CAS RN CA Index name /
IUPAC name EC No.
Acrylic polymer(s)
(Including non-hazardous
ingredients)
≥98.5% 25852-37-3
2-Propenoic acid,
2-methyl-, methyl
ester, polymer
with butyl
2-propenoate
Not
applicable
Water ≤1.5%
KANE ACE M-577
Page 2 of 5
2016/9/21
KANEKA Corporation M-577-a01
4.FIRST-AID MEASURES
Inhalation Move victim to fresh air. Call a physician.
Skin Flush with flowing water for 15minutes, then wash area with
mild soap and water. Call a physician.
Eyes In case of contact, immediately flush eyes with flowing water
for at least 15minutes, occasionally lifting upper and lower
lids, until no evidence of chemical remains. Get medical
attention.
Ingestion Have victim rinse mouth with water or give several cupful of
water, if conscious. Get medical attention.
5.FIRE-FIGHTING MEASURES
Extinguishing media Water spray ,dry chemicals, foam, or carbon dioxide.
Special fire fighting procedures Avoid scattering burning material.
Wear self-contained breathing apparatus and full protective
equipment. Use water spray to keep containers cool.
Unusual fire and explosion
hazards
Irritating fumes may develop when product is heated. Dust
can form explosive mixture in the air.
Dust generation should be minimized. Every ignition source
such as; fire, open flame, static sparks, heated surfaces, etc.,
even in closed pipelines or equipment, should be strictly
prohibited. Extended exposure to high temperatures
reduces the auto-ignition temperature.
6.ACCIDENTAL RELEASE MEASURES
Spill response Carefully vacuum up material with vacuum equipment that is
grounded to avoid sparks and place in a suitable container for
disposal.
Avoid creating a dusty atmosphere. Dampen spill with water
to reduce dust. The accumulation of dusts of product can
create a serious hazard of dust explosion.
Avoid release to open waters. No data is available on
aquatic life if product is released to open waters.
7.HANDLING AND STORAGE
Handling Ventilate area properly to avoid unnecessary exposure to
resulting gases which might be hazardous. Do not cause
dust clouds or static sparks. When transferring, avoid
creating dust. Ground all equipment to avoid static sparks.
Use personal antistatic equipment to avoid static charge.
Avoid contact with eyes, skin, and clothing. Use personal
protective equipment as required. Wash thoroughly after
handling.
Storage Store in original container in cool, dry area and protect from
light. Do not store near high temperature, boilers, heaters,
hot pipes, open flames or oxidizing agents.
Keep away from food and drinks.
KANE ACE M-577
Page 3 of 5
2016/9/21
KANEKA Corporation M-577-a01
8.EXPOSURE CONTROLS/PERSONAL PROTECTION
Ventilation Local exhaust is recommended. Maintain low dust
concentration. See FIRE-FIGHTING MEASURES section.
Respiratory protection Use NIOSH approved high efficiency dust respirator when
dusty conditions prevail. No TLV-TWA has been established
for this dust. The AGCIH recommended that nuisance
particulates be limited 10 mg/m3
, total dust. During molten
or heating process, use an organic vapor respirator.
Eye and face protection Chemical workers goggles. Do not wear contact lenses.
Other clothing and equipment Rubber gloves. An eyewash and emergency shower should
be readily available. Launder contaminated clothing before
reuse.
9.PHYSICAL AND CHEMICAL PROPERTIES
Appearance and odor White powder with slight acrylic ester odor
pH Not available
Boiling point/Freezing point Not applicable
Flash point Not applicable
Evaporation rate Not applicable
Vapor pressure/Vapor density Not applicable
Specific gravity 1.0-1.2 at 4℃
Solubility in water Insoluble
Solubility in organic solvent Swell on/Dissolve in exposure to organic solvents(toluene,
benzene etc).
Partition coefficient:
n-octanol/water
Not available
Auto-ignition temperature 460-470℃
Volatiles ≤1.5%(60 minutes at 105℃)
Molecular weight Not available
10.STABILITY AND REACTIVITY
Stability Stable
Conditions to avoid Avoid contact with oxidizers. Avoid exposing dust to ignition
sources.
Incompatibility(Materials to avoid) Oxidizers
Hazardous polymerization Will not occur
Hazardous decomposition
products
Carbon monoxide, carbon dioxide, and various oxidized and
non-oxidized hydrocarbons.
KANE ACE M-577
Page 4 of 5
2016/9/21
KANEKA Corporation M-577-a01
11.TOXICOLOGICAL INFORMATION
Acute toxicity No data is available on this exact polymer. Similar polymers
have an LD50 rats > 2,000mg/kg.
Skin corrosion/irritation May cause irritation.
Eye contact May cause irritation.
Skin contact May cause irritation and/or dermatitis.
Germ cell mutagenicity No data currently available.
Carcinogenicity No data currently available.
Toxic to reproduction No data currently available.
Specific target organ toxicity
(Single exposure)
No data currently available.
Specific target organ toxicity
(Repeated exposure)
No data currently available.
Inhalation Irritating to the respiratory tract. Treat as nuisance dust.
Odorous fumes may result from normal processing.
12.ECOLOGICAL INFORMATION
Toxicity No data currently available.
Persistence and degradability No data currently available.
Bioaccumulative potential No data currently available.
13.DISPOSAL CONSIDERATIONS
Recommended disposal Dispose of material / container as solid waste in a closed
container in accordance with local / regional / national /
international regulations.
14.TRANSPORT INFORMATION
UN number Nor applicable
Department of
transportation(DOT) proper
shipping name
Not required
DOT hazard class Not required
DOT Label Not required
DOT ID# Not required
KANE ACE M-577
Page 5 of 5
2016/9/21
KANEKA Corporation M-577-a01
15.REGULATORY INFORMATION
JAPANESE REGULATIONS
Industrial Safety and Health Act
Not regulated
Act on the Evaluation of Chemical Substances and Regulation of Their Manufacture, etc
Existing chemical substances
Act on Confirmation, etc. of Release Amounts of Specific Chemical Substances in the
Environment and Promotion of Improvements to the Management Thereof
Not regulated
Fire Defense Law
Designated Flammable Materials
(Synthetic Resin – Non-Foam, ≥3,000kg)
Poisonous and Deleterious Substances Control Law
Not regulated
CHINESE REGULATIONS
Not regulated
TAIWANESE REGULATIONS
Labor Safety and Health Law
Not regulated
SOUTH KOREAN REGULATIONS
Not regulated
16.OTHER INFORMATION
INVENTORYS for POLYMERS
ENCS(Japan) Existed, No: Trade secret
EINECS/ELINCS(EU) EINECS: Polymer, all monomers(>2%) listed
ELINCS: Not listed
TSCA(USA) Listed
DSL/NDSL(Canada) DSL: Listed, NDSL: Not listed
AICS(Australia) Listed
ECL(Korea) Listed, No: KE-25065
PICCS(Philippines) Listed
IECSC(China) Listed
NZIoC(New Zealand) Listed
NECSI (Taiwan) Listed
The information set forth herein has been gathered from standard reference materials
and/or KANEKA Corporation test data and to our best knowledge and belief accurate and
reliable. Such information is offered solely for a your consideration, investigation and
verification, and it is not suggested or guaranteed that the hazard precautions or
procedures mentioned are the only ones which exist. KANEKA Corporation makes no
warranties, express or implied, with respect to the use of such information or the use of the
specific material identified herein in combination with any other material or process and,
therefore, assumes no responsibility. While our technical personnel will be happy to
respond to questions regarding safe handling and use procedures, safe handling and use
remains the responsibility of the customer.​