供处理污水成本低 无烟煤滤料
无烟煤滤料介绍
无烟煤工艺
精制无烟煤滤料采用山西优质无烟煤为原料，经精选、破碎、和两次筛分而成，外观光泽好，呈球状，机械强度高，抗压性能好，化学性能稳定，不含有毒物质，耐磨损，在酸性、中性、碱性水中均不溶解，另外无烟煤颗粒表面粗糙，有良好的吸附能力，孔隙率大(>50%)，有较高的含污能力，因质轻，所需反冲洗强度较低，可节省大量反冲洗水量及电能。
无烟煤滤料同石英砂滤料配合使用是我国目前推广的双层快速滤池和三层滤池、滤罐过滤的最佳材料。是提高滤速增加单位面积出水量和成倍提高截污能力，降低工程造价和减少占地面积最有效的途径。广泛用于化工、冶金、热电、制药、造纸、印染、食品等生产前后的水质处理过程中。
无烟煤特点
无烟煤滤料是一种水处理行业过滤用滤料，是特别从深井矿物中精选的，具有最高的含碳量百分比。无烟煤滤料采用人工分类，可减少无关矿物质并降低灰分含量，经过过滤和冲洗，确保其适合水过滤之用。 由于具有较好的固体颗粒保持能力，因此无烟煤能够可靠地提高悬浮颗粒清除能力。
无烟煤滤料技术参数
分析项目 | 分析数据 | 分析项目 | 分析数据 |
含碳量% | ≥85 | 盐酸可溶率% | ≤3.5 |
比重g/cm | 1.4-1.6 | 磨损率% | ≤1.4 |
容重g/cm | 0.98 | 破碎率% | ≤1.6 |
含泥量% | ≤4 | 空隙率% | 47-53 |
无烟煤滤料是目前普遍采用的最佳过滤材料。矿源主来自山西晋城和阳城两大煤田。它用途广泛，适应范围大。可用于生活饮用水和工业生产用水以及各种池型的普通快滤池。双层及三层滤池，各种污水过滤器，净水机械过滤器及化工、冶金、热电、制药、造纸、印染、食品等的生产前后的水质处理。
无烟煤滤料包装及储运
用耐用织物袋包装，净重25kg。运输储存期间防止包装破损，以免漏失或混入杂物．不宜与承托料及其他滤料一起运输堆放。
无烟煤常用规格
常用规格一般为：0.5－0.8mm，0.8－1.2mm，0.8－1.8mm，1－2mm，2－4mm等。
锻烧无烟煤产品介绍
锻烧无烟煤俗称白煤或红煤。是煤化程度最大的煤。无烟煤固定碳含量高，挥发分产率低，密度大，硬度大，燃点高，燃烧时不冒烟。黑色坚硬，有金属光泽。以脂摩擦不致染污，断口成介壳状，燃烧时火焰短而少烟。不结焦。一般含碳量在90%以上，挥发物在10%以下。无胶质层厚度。热值约8000-8500千卡/公斤。有时把挥发物含量特大的称做半无烟煤；特小的称做高无烟煤。
锻烧无烟煤特性
无烟煤为煤化程度最深的煤，含碳量最多，灰分不多，水分较少，发热量很高，可达25000~32500kJ/kg，挥发分释出温度较高，其焦炭没有黏着性，着火和燃尽均比较困难，燃烧时无烟，火焰呈青蓝色 。 煤样在规定条件下隔绝空气加热，煤中的有机物质受热分解出一部分分子量较小的液态（此时为蒸汽状态）和气态产物，这些产物称为挥发物。挥发物占煤样质量的分数成为挥发分产率或简称为挥发分。以干燥无灰基为分析基，挥发分低于10%的煤称为无烟煤。挥发分大于6.5%小于10%的无烟煤称为无烟煤三号。01号无烟煤为年老无烟煤；02号无烟煤为典型无烟煤；03号无烟煤为年轻无烟煤。
无烟煤中国储量
中国无烟煤预测储量为4740 亿吨，占全国煤炭总资源量的10%，年产2 亿吨。山西省占32%，河南省占18%，贵州省占11%。中国有六大无烟煤基地：北京京煤集团，晋城煤业集团，焦作煤业集团，河南永城矿区，神华宁煤集团，阳泉煤业集团。
锻烧无烟煤应用
无烟煤块煤主要应用是化肥（氮肥、合成氨）、陶瓷、制造锻造等行业；无烟粉煤主要应用在冶金行业用于高炉喷吹（高炉喷吹用煤主要包括无烟煤、贫煤、瘦煤和气煤）。
锻烧无烟煤在分解炉的使用
分解炉的作用是在固相悬浮于热气体的条件下完成碳酸盐的分解吸热反应。
CaCO3=CaO+CO2↑
在所提供的热量不能使生料完全分解的情况下，分解过程可按CO2的分压达到某一平衡状态考虑。一般来说分解炉的平衡状态温度处于850～900℃范围。分解炉内的温度分布与下列因素有关。
1）燃烧成气相视的放热速率。
2）由气相传给固体生料粉的传热速率。
3）生料颗粒分解时的吸热速率。
无烟煤注意事项
与使用烟煤相比，由于无烟煤挥发份较低，因此需要一个相对较大的分解炉，以期获得相同的生料分解率和相同的煤粉燃烬程度，或者要求一个较高的操作温度，或者将无烟煤磨得更细一些。
当三次风温较低时，无烟煤挥发出来的气体往往不能产生足够的热量使温度升高。，所以将煤粉直接喂入温度范围通常在1000～1200℃的上升烟道废气中可确保煤粉燃烧。
另外需要提出的是燃烧速度和燃烬时间还取决于烟气中的O2含量，用较高的空气过剩系数操作分解炉时刻缩短燃烬时间，但通常增大空气过剩系数的做法将会增加通过预热器的气体流量。为此将造成较大的压差和较高的废气温度，从而使窑主排风机的负荷增大，整个窑系统的单位热耗也将有所增加。
改变生料喂入方式是相当重要的，采用无烟煤操作时，无烟煤与生料粉的混合最好能有适当的滞后时间，以保证无烟煤的点燃，因此对喂入分解炉的生料需要进行分级控制，以便使分解炉底部形成一个相对高温区。判断生料在分解炉内是否达到预期的效果，最好的办法是检测入窑生料分解率，如果入窑生料分解率达到了预期效果，说明无烟煤在分解炉内的燃烧是合适的。
无烟煤在窑头燃烧器的使用
新型干法水泥生产线装备有现代化的燃烧器，现代化的燃烧器配备有适当的火焰调节装置，可以使无烟煤没有任何问题地在窑头进行燃烧。 燃烧器的作用不仅仅是输送和分布煤粉，更主要的是保持火焰的理想长度和合适的气体流场。火焰的长度对于新型干法窑来讲十分重要，火焰如果过短，煤的潜热只能在较小体积内释放出来，火焰的温度就会在局部变得很高，相反，如果火焰长度加长，温度就会下降。火焰的长度主要靠燃烧器的推动力进行控制。
燃烧器的推动力=一次空气（kg/s）×燃烧器尖端风速（m/s）
当燃烧器推动力加大时火焰长度缩短。
原煤的种类对火焰的长度并不十分重要，只要求单个煤粒子的燃烬时间小于其在火焰中的停留时间即可。
如果目标是让无烟煤与烟煤保持相同的火焰长度，那么就必须对煤粉的燃烬时间进行补偿。简单的做法就是将无烟煤磨得更细一些。
高温二次风将会快速加热进入燃烧器的煤粉的挥发分快速排出，煤粉一经离开燃烧器端部，焦炭粒子就会点燃，因此冷却机的使用效果将对无烟煤的使用产生一定影响。
在回转窑窑头燃烧器上使用无烟煤需要保证如下条件：
1）煤粉能达到足够的符合要求的细度，以保证燃烧和火焰形成。
2）控制可靠稳定的煤粉喂料。
3）燃烧器的一次分必须具有足够的推动力并可调节。
4）燃烧器必须能够在燃烧带产生有充分内部循环空气的火焰，以保证无烟煤尽快点燃。
5）在启动冷窑或窑况不正常时利用烟煤或燃油辅助燃烧。
联系方式
厂名称：温县星月活性炭厂
工厂地址：河南省焦作温县番田镇前杨垒村
联系人：李花蕾
手 机：18768857326
电 话：0371-60266813
Q Q ：1295230430
邮 箱：1295230430@qq.com
网址：http://xyt666666.cn.alibaba.com
英文翻译
Anthracite filter material is introduced
Anthracite coal technology
Refined anthracite filter material used in Shanxi Province high quality anthracite as raw material, after the selection, crushing, and two screening and become, appearance luster good, spherical, high mechanical strength, good compression performance, stable chemical performance, does not contain toxic substances, the resistance to wear and tear, does not dissolve in acidic, neutral and alkaline water, additional anthracite coal particle surface is rough, with good adsorption ability, large porosity (> 50%), had a higher carrying capacity, due to the light, the backwash intensity is low, can save a lot of backwash water and electricity. Anthracite filter material and quartz sand filter material used in the current promotion of double quick filter and three layer filter, cartridge filter, one of the best materials. Increase the water yield per unit area is to improve the filtering speed and multiply section carrying capacity, reduce the project cost and the most effective way to reduce cover an area of an area. Widely used in chemical industry, metallurgy, thermal power, pharmaceutical, paper making, printing and dyeing, food, etc. In the process of production of water quality before and after treatment.
Characteristics of anthracite coal
Anthracite filter material is a kind of filter material for water treatment industry, is selected in the special minerals from a deep well, has the highest carbon content percentage. Anthracite filter material using artificial classification, can reduce irrelevant minerals and lower ash content, after filtration and washing, make sure it is suitable for water filtration. Because good solids retention, anthracite can be reliably improve suspended particle removal ability.
Anthracite filter material parameters
Analyze project data analysis data analysis project analysis
Carbon content % % p 85 hydrochloric acid soluble rate is 3.5 or less
The proportion of 1.4 1.6 g/cm wear rate % 1.4 or less
Breakage % 1.6 or less bulk density 0.98 g/cm
Silt content % % 4 or less air voids 47 to 53
Anthracite filter material is the best filter material widely used. Source from jincheng and activation of two coal field. It is widely used, adapted to large range. Can be used for drinking water and industrial water as well as a variety of pool type of ordinary filter. Double layer and three layer filter, all kinds of water filters, water purification machine filters and the chemical industry, metallurgy, thermal power, pharmaceutical, paper making, printing and dyeing, food, etc. The production of water quality before and after treatment. Anthracite filter material packaging and storage
With durable fabric bags, net weight 25 kg. Stored during transport to prevent damaged packaging, in order to avoid loss or mixed with sundry. Unfavorable transportation stacked together with supporting and other filter material.
Anthracite coal commonly used specifications
Commonly used specifications for: 0.5-0.8 mm, 0.8 1.2 mm, 0.8 1.8 mm, 1-2 mm, 2-4 mm, etc.
Forging burn anthracite products is introduced
Forging burn anthracite is commonly known as red stone coal or coal. Is the largest degree of coalification of coal. Volatile anthracite fixed carbon content, high yield, low density, high hardness, high flash point, do not smoke during burning. Black solid, with metallic luster. As fat friction does not stain, fracture into conchoidal, burns, short flame and smoke less. No coking. General carbon content above 90%, the volatile matter below 10%. No glue layer thickness. Calorific value of about 8000-8500 kcal/kg. The volatile matter content of very large sometimes referred to as half anthracite coal; Small called high anthracite.
Forging burn anthracite characteristics
Anthracite as the degree of coalification coal, the most the most carbon content, ash content, moisture content is less, the calorific value is very high, up to 25000 ~ 32500 kj/kg, volatile release temperature is higher, the coke without adhesion, ignition and burnout are more difficult, smokeless burning, the flame of the blue. Coal samples under prescribed conditions the air heating, coal thermal decomposition of organic matter in the part of the smaller molecular weight liquid (state) at this time for steam and gas products, these products are called volatiles. Points to the quality of volatile matter of coal sample become volatile yield or volatile for short. To dry ash-free basis for the analysis basis, known as anthracite coal volatile matter less than 10%. Volatile is more than 6.5% less than 6.5% of the anthracite is called used no. 3. 01 anthracite anthracite for old age; No. 02 anthracite for typical used; 03 anthracite anthracite for the young.
Anthracite coal reserves in China
China anthracite predicted reserves of 474 billion tons, accounting for 10% of the total coal resources across the country, annual output of 200 million tons. Shanxi Province accounted for 32%, 18%, in henan province guizhou province accounted for 11%. Six major anthracite base in China: Beijing Beijing coal group, jincheng coal group, jiaozuo coal group, the city always in henan mine, shenhua ningxia coal group, yangquan coal group.
Forging burn anthracite applications
Anthracite lump coal is the main application of chemical fertilizer (nitrogen, ammonia), ceramics, the manufacturing of forging; Anthracite pulverized coal is mainly used in metallurgical industry for blast furnace injection (injection in the blast furnace coal mainly includes anthracite, lean coal, lean coal and gas coal). The use of forging burn anthracite coal in the calciner
The function of decomposing furnace is under the condition of solid phase suspended in hot gas carbonate decomposition endothermic reaction. CaCO3 = write CaO + CO2
Provided the quantity of heat cannot make raw materials under the condition of complete decomposition, decomposition process according to the partial pressure of CO2 reaches an equilibrium state. In general balance temperature of decomposing furnace is in the range of 850 ~ 900℃. Decomposition temperature distribution inside the furnace is related to the following factors. 1) the combustion heat release rate of gas each other. 2) by passing from gas to solid raw powder, heat transfer rate. 3) decomposition heat absorption rate of the raw material particles. Anthracite coal
Compared with using bituminous coal, due to the low anthracite volatile flux, so need a decomposing furnace is relatively large, in order to obtain the same raw material decomposition rate and pulverized coal combustion degree, state of the same or require a higher operating temperature, or some will be more fine anthracite coal mill. When three blast temperature is low, anthracite volatile out often cannot generate enough heat to make gas temperature. The pulverized coal directly feeding temperature range, often rising in 1000 ~ 1200℃to ensure pulverized coal combustion flue gas. Also need to come up with is burning rate and combustion time also depends on the state of O2 content in flue gas, with a high excess air coefficient decomposition furnace operation time shorten the combustion time state, but will usually increase the excess air coefficient increase the gas flow through the preheater. This will cause large pressure difference and high exhaust temperature, thus make kiln-owners' exhaust fan load increases, the unit heat consumption of the whole kiln system will also increase. Change the raw meal feeding way is quite important, use anthracite, anthracite mixed with raw powder of it is best to have appropriate lag time, to ensure the lighting of anthracite, so to feed raw materials need to be graded control of decomposing furnace, so that the decomposition at the bottom of the furnace to form a relatively high temperature. Whether raw materials on the decomposition furnace, achieve the desired effect, is the best way to test the soil of decomposition rate, if the meal decomposition rate of the desired effect, in that anthracite combustion inside the furnace is appropriate.
The use of anthracite coal in a kiln burner head
NSP cement production line is equipped with modern burner, modernization of the burner equipped with proper flame adjustment device, can make the anthracite coal combustion without any problems at the kiln head. Pulverized coal burner role is not only a transmission and distribution, more major is to keep the flame of the ideal length, and proper gas flow field. Flame is very important for NSP kiln, the length of the flame if too short, the latent heat released only in a small volume of coal, the flame temperature will become very high in local, on the contrary, if the flame length is longer, the temperature will drop. Mainly by the burner flame length of thrust control. Burner boost air (kg/s) = a * burner tip wind speed (m/s)
When the burner impetus to increase flame length shorter. Crude coal type on the flame length is not very important, only requires a single coal particle combustion time is less than the state in the flame residence time can be. If the goal is to let the flame of anthracite and bituminous coal to keep the same length, then it must be for pulverized coal combustion time for state compensation. It is simple to anthracite more fine grinding. High temperature secondary air will rapid heating into pulverized coal burner in the volatile rapid eduction, pulverized coal is left burner ends, coke particles will be light, so the use effect of the cooling machine will affected the use of anthracite coal. Using anthracite on rotary kiln burner head need to make sure that the following conditions:
1) pulverized coal fineness can reach enough to meet the requirements, to ensure that the combustion and flame. 2) reliable and steady control of pulverized coal feeding. 3) burner a points must have sufficient driving force and adjustable. 4) burner must be able to have sufficient internal circulating air in combustion zone of the flame, and to ensure that the anthracite as soon as possible. 5) in the abnormal startup cold kiln or conditions when using bituminous coal or fuel oil auxiliary combustion.
Contact way
The factory name: county and activated carbon plant
Factory address: jiaozuo in henan county tian town before Yang lei village
Contacts: LiuKaiTian
Hand machine: 18768857326
Telephone: 0371-60266813
Q Q: 1295230430
Mail box: 1295230430 @qq.com < mailto:1295230430@qq.com >
Url: < http://xyt666666.cn.alibaba.com >
产品展示
联系方式
厂名称：温县星月活性炭厂
工厂地址：河南省焦作温县番田镇前杨垒村
联系人：李花蕾
手 机：18768857326
电 话：0371-60266813
Q Q ：1295230430
邮 箱：1295230430@qq.com
网址：http://xyt666666.cn.alibaba.com
