脱水机，塑料及纺织的脱水，技术工程师推荐的好产品！ 

【联系方式：13829243968】【联系人：刘经理】

【QQ客服：2854820654】              

【公司地址：广东省东莞市清溪镇清厦村科技路西四街A栋一楼】

建星牌三足离心机的工作原理:

脱水机以离心运动为其工作原理,即由电动机带动内胆作高速转动,被脱物中的水份在高速旋转下离心运动,水从内胆壳的四周眼中飞溅出内胆,达到脱水的目的.

建星牌三足离心机的结构：

1、本脱水机为三足悬摆式结构，三足装有弹簧，可避免因转鼓内载重不平衡而在运转时产生地脚振动。

2、外壳和内胆系优质不锈钢板所制，底盘材料为铸铁，出水管在底盘下方,底脚座及柱脚材料均为铸铁.

3、其主轴采用优质钢材所制,装有两只轴承,下端用推力球轴承支持,以减少磨损,节省动力.

4、转鼓采用不锈钢板钮孔制成,笼底座为铸铁件,并衬有不锈钢底罩.转鼓装有主轴上端的锥面上,以保证运转平稳.

本脱水机采用了独立的电动机通过三角胶带传动,装有离心式起步法兰,可使机器缓步起动,其制动效能高,能使转鼓迅速停转,可转免主轴因制动而受扭力.

建星牌三足离心机的操作方法:

1:将需脱水之物品均匀平整地装入鼓内,注意平衡,切勿超载.

2:工作时,开动机电,约经90秒钟,机器达到正常转速,出水管开始出水.

3:电机开机8至10分钟,水管无水外流,即可切断电源.

4:刹车:正常情况下断电1-2分钟,分几次慢慢制动开合臂刹车,机器停转.

三足离心机注意事项:

1:操作者必须熟悉机器的机构\性能和操作方法.

2:开车前先转运刹数转,检查转鼓运转情况.

3:加料应均匀分布,以免偏重过大造成机器振动过大。

4:正常运转时,切勿制动开合臂,以免损坏兰令带及其它零件.

5:顶盖上切勿放置任何物品,以免开车后发生意外事故.

6:运转时一旦发生异常现象,应立即切断电源,刹车停机检查.

7:机器必须定期检修,加注润滑油,每半年至少检修一次.

8:机器运转必须按红箭头所示顺时针方向旋转.

三足离心机的安装:

1\机器必须安装在紧固的地基上,并用3根地脚螺栓固定牢固.

2\地基必须用水平仪校正水平.

Build star three-legged centrifuges working principle:
Dewatering machine is provided with eccentric exercise for its working principle, namely by the motor to drive the tank for high speed rotation, is to take off the content in the water under the high speed rotating centrifugal movement, splash water from the tank shell around the eyes out of the tank, to achieve the purpose of dehydration.
The structure of the building star three-legged centrifuges:
1, the dehydrator for suspension pendulum structure with three legs, three feet fitted with springs, can be avoided because the drum load imbalance in the foundation vibration during operation.
2, shell and inner quality was made of stainless steel plate, chassis material is cast iron, outlet pipe at the bottom of the chassis, the foot material are all cast iron base and column.
3, its main shaft adopt high quality steel, equipped with two bearings, the bottom support by thrust ball bearing, in order to reduce wear and save power.
4, the drum is made of stainless steel plate made buttonhole, cage base for iron casting, and lined with stainless steel bottom cover. On the drum is equipped with the cone at the top of main shaft, so as to ensure smooth operation.
The dewatering machine adopts the independent motor through a triangle belt transmission, equipped with the centrifugal start flange, can make the machine slowly starting, the braking efficiency is high, can make the drum stops, quickly convertible from the spindle for braking torque.
Build star three-legged centrifuges operating methods:
1: the dewatering, the items of uniform neatly into drum, pay attention to the balance, please do not overload.
2: work, start the electrical and mechanical, with about 90 seconds, the machine to normal speed, start water outlet pipe.
3: motor start up 8 to 10 minutes, without water outflow conduit, can cut off power supply.
4: the brake: under normal circumstances without electricity for 1 to 2 minutes, points a few times slowly the brakes, brake movable arm machine halt.
A three-legged centrifuges to note:
1: the operator must be familiar with machine mechanism, performance and operation method.
2: before driving transit brake turn number first, check the workings of the drum.
3: material should be evenly distributed, in order to avoid too much heavy machine vibration caused by too much.
4: during normal operation, do not brake movable arm, so as to avoid damage to belt and other parts.
Do not put any item 5: on the roof, so as to avoid driving after the accident.
6: when running in the event of abnormal phenomenon, should immediately cut off power supply, the brakes stop check.
7: the machine must be regularly maintenance, filling grease, maintenance at least once every six months.
8: the machine must be in accordance with the red arrow shown in clockwise.
A three-legged centrifuges to install:
1 \ the machine must be installed on the fastening of the foundation, use 3 anchor bolt is fixed firmly.
2 \ the foundation must use level calibration level.

特别警示:

  本机为机电设备,安装时务必使该设备可靠按地,以免发生人身及设备安全事故!

【联系方式：13829243968】【联系人：刘经理】

工程案例：

【联系方式：13829243968】【联系人：刘经理】

【联系方式：13829243968】【联系人：刘经理】

下图为立式脱水机：

下图为圆桶脱水机：


公司简介：

   东莞市建星环保科技有限公司是一家民营环保科技企业，专业从事塑胶、化工及食品行业的节能机械，集研发、设计、制造、销售与服务的综合性企业。为方便新老客户的光临，加工基地设立于东莞市清溪镇镇中心；我公司坚持走技术创新道路，逐步建立起建星品牌在国际市场的影响力、知名度和美誉度。

   在产品的销售上，客户的利益是我们首先考虑的，我们的服务追求精细化，从售前的咨询、热心服务到售中的推介产品，我们都要求精中求细。强大的设计开发、生产制造、安装调试、技术维修、不定期回访，严格的质量保证和快捷到位的售后服务，每一环节都做了精心安排，解决了客户一系列的后顾之忧。

   我公司非常重视人才的培养和引进，完善的招聘、培训流程及职业规划体系，大胆起用高技术人才，为建星环保公司快速、稳健的发展，提供了强有力的支持！

查看更多，请点击这里