Features:
1 centrifuge cycle design. High pressure, air volume. Air cushion design, lower noise
2 starting torque, stable and reliable working process
3 oil-free design, more pure gases
4 surface phosphate treatment. Electrostatic spraying, color uniformity, adhesion stronger
5.-power wide range of configurations, long product life.
Usage:
Suitable for Cutter, cigarette filter machine, plating bath stirring, spray dryers, water aeration, screen printing, photolithography machine, injection molding machine automatic feeding dryer, liquid filling machine, welding equipment, film machinery, paper, transportation, dry laundry, cleaning, aspects of air dust, dry bottles, gas transmission, feeding, collection.
Instructions:
Rick combined high pressure air needs to be placed in a dry and ventilated place above the horizontal.
产品特点:
1.离心循环设计。压力高、风量大。气流缓冲设计,噪音更低
2.启动力矩小,工作过程稳定可靠
3.无油润滑设计,气体更纯净
4.表面磷化处理。静电喷涂,色泽均匀,附着力更强
5.功率配置范围广,产品使用寿命长.
产品用途:
适用于切纸机、卷烟滤嘴成型机、电镀槽液搅拌、雾化干燥机、水处理曝气、丝网印刷机、照相制版机、注塑机自动上料烘干机、液体灌装机、电焊设备、电影机械、纸张运送、干洗衣服、清洗、空气除尘、干瓶、气体传送、送料、收集等方面。
使用须知:
需将合瑞克高压风机放置在高于水平面干燥通风处。
Maintenance and reason together Rick pressure fan failure
(A) maintenance of the system fan
1 fan must hand use, hand repair.
2 fans run allowed sick.
3 periodically clear the fan inside the dust, especially on the impeller dust, dirt and other impurities, to prevent rust and imbalance.
4 fan maintenance must be emphasized first off parking.
5 sensitivity regular inspection of the thermometer and oil targets.
6 In addition to the lubricant should be replaced after each dismantling repair, but under normal circumstances, from March to June change the oil.
The main causes of failure and (b) the fan
1 bearing housing severe shock
① different heart fan shaft and motor shaft, coupling mounted crooked
② casing or impeller inlet and friction
③ foundation is not solid steel degree
④ impeller or impeller deformed rivet loose
⑤ impeller shaft drive shaft loose, loose bolts or coupling
⑥ chassis with the bracket, bearing housing and bracket, bearing cover on the seat, such as loose coupling bolts
⑦ bad fan out of gas pipeline installation
⑧ rotor imbalance, Fan blade wear
2 bearing temperature is too high
① severe shock bearing box
② grease quality is not lit, deterioration, contains too much dust, sticky sand, dirt and other impurities
③ bearing cover, seat bolts tightening force is too large or too small
④ shaft with rolling bearing installation skew, after two bearing different heart
⑤ bearing damage
3 electrode current or temperature is too high
① When the drive into the gas pipeline is not shutting the gate or throttle
② traffic exceeds the specified value
③ fan conveying gas density is too large or sticky substance
④ motor input voltage is too low or the power supply single phase power outages
⑤ coupling connection errors, aprons too tight or uneven gaps
⑥ subject to severe vibration effects bearing box
合瑞克高压风机的维护与故障原因
(一)风机维护工作制度
1.风机必须专人使用,专人维修。
2.风机不许带病运行。
3.定期清除风机内部的灰尘,特别是叶轮上的灰尘、污垢等杂质,以防止锈蚀和失衡。
4.风机维修必须强调首先断电停车。
5.对温度计及油标的灵敏性定期检查。
6.除每次拆修后应更换润滑油外,正常情况下3-6月更换一次润滑油。
(二)风机的主要故障及原因
1.轴承箱剧烈震动
①风机轴与电机轴不同心,联轴器装歪
②机壳或进风口与叶轮摩擦
③基础的钢度不牢固
④叶轮铆钉松动或叶轮变形
⑤叶轮轴盘与轴松动,或联轴器螺栓松动
⑥机壳与支架、轴承箱与支架、轴承箱盖于座等联接螺栓松动
⑦风机进出气管道安装不良
⑧转子不平衡,引风机叶片磨损
2.轴承温升过高
①轴承箱剧烈震动
②润滑油脂质量不亮、变质、含有过多灰尘、粘沙、污垢等杂质
③轴承箱盖、座连接螺栓紧力过大或过小
④轴与滚动轴承安装歪斜,前后两轴承不同心
⑤滚动轴承损坏
3.电极电流过大或温升过高
①开车时进气管道闸门或节流阀未关严
②流量超过规定值
③风机输送气体的密度过大或有粘性物质
④电机输入电压过低或电源单相断电
⑤联轴器连接不正,皮圈过紧或间隙不匀
⑥受轴承箱剧烈震动的影响