E14灯头通规  7006-27F-1

Go gauge for E14 caps on finished lamps 7006-27F-1

量规螺纹边缘尖锐部分应以0.2mm~0.3mm的半径倒圆。

The sharp part of the thread shall be broken with a radius of 0.2 mm to 0.3 mm.

目的：

Purpose:

检验成品灯上E14灯头螺纹最大尺寸和尺寸T1 min.

 To check the maximum dimensions of the screw thread and dimension T1 minimum of E14 caps on finished lamps.

 检验：

Testing:

当成品灯上的灯头完全旋入量规内时，灯头中心触点应与X面共面或凸出X面。

When the cap on a finished lamp has been screwed into the gauge as far as it will go, the centre contact shall be co-planar with, or project  beyond surface X.

E14灯头止规  7006-28B-1

Not Go gauge for E14 caps on finished lamps

目的：

PURPOSE:

检验成品灯上E14灯头螺纹最小外径（尺寸d）。

To check the minimum outside (major) diameter of the screw thread, dimension d, of E14 caps on finished lamps.

检验：

TESTING:

当量规套在成品灯（灯头向上）的灯头螺纹上时，灯头中心触点不应凸出量规的X面。检验仅利用量规的自身质量进行。

When the gauge is placed over the thread of the cap on a finished lamp, held cap uppermost, the centre contact shall not project beyond surface X. Only the weight of the gauge itself shall be used in the test.

E14灯头接触性能规 7006-54-2

Gauge for finished lamp fitted with E14 caps for testing contact making:7006-54-2

 目的：

PURPOSE:

检验灯座相关灯座中接触性能的尺寸。

To check lamp dimensions for contact making in IEC holders.

 检验：

TESTING:

如果灯插入量规时，W面可以与V面共面或凸出V面，则可以认为灯的形状与灯座配合是合格的。 此量规仅适用检验装有GB/T1406.1 7004-23中所示的E14灯头的烛形灯、球形灯、家用管形灯和小形灯。

The shape of the lamp with regard to the fit in the lampholder is assumed to be correct if the lamp can be pushed into the gauge till plane W reaches plane V or projcts beyond it.

E14灯头焊锡高度规，又名S1通规  7006-27G-1

Go gauge for dimension S1 of E14 caps  7006-27G-1

目的：

PURPOSE:

检验成品灯上E14灯头尺寸S1的最大值和最小值。

To check the deminsion S1 minimum and S1 maxiimum of E14 caps on finished lamps.

检验：

TESTING:

当成品灯的灯头完全插入量规时，柱塞的W面应与X面共面或凸出X面，但不应凸出Y面。

When the cap on a finished lamp has been pushed into the gauge as far as it will go, the plunger surface W shall be co-planar with or project byond surface X but it shall not project beyond surface Y.

E14防意外接触规 7006-55-2  GB/T1483.1

Gauge for finished lamps fitted with E14 caps for testing protection against accidental contact 7006-55-2 IEC60061-3

目的：

PURPOSE:

检验防意外接触性能。

To check protection against accidental contact.

检验：

TESTING:

当成品灯上灯头完全插入量规时，W面没凸出V面，则可以认为灯防意外接触性能上合格的。

The shape of the lamp with regard to protection against accidental contact is assumed to be correct if the test sample being pushed as far as possible into the gauge, plane W does not protrude beyond plane V.

此量规仅适用检验装有符合GB/T1406.1 7004-23中所示的E14灯头的烛形灯球形灯、家用管形灯和小型灯。

The application of this gauge is restricted to the following lamps when they are fitted with E14 caps, in accordance with sheet 7004-23: Candle lamps, Round bulb lamps, Domestic tubular lamps, Pygmy lamps.

广东安规检测有限公司设计生产的E14灯头量规一套包含E14灯头通规、E14灯头止规、E14 适用于E14螺口灯头的球泡光源的质量检测。

产品完全符合标准IEC60061-3|GB/T1483.1，100%通过计量检定。

专业安规公司，富有行业经验的专业团队

精选优质材料生产，质量保证。