E40灯头通规 7006-27-7

Go Gauge For E40 Caps on Finished Lamps

 量规螺纹边缘尖锐部分以0.2mm～0.3mm的半径倒圆。

The sharp part of the edge of the thread shall be broken with a radius of 0.2mm to 0.3 mm.

 目的：

Purpose:

检验成品灯上E40灯头螺纹最大尺寸和尺寸T1min。

To check the maximum dimensions of the screw thread and dimension T1 minimum of E40 caps on finished lamps.

 检验：

Testing:

当成品灯上的灯头完全旋入量规内时，灯头中心触点应与X面共面或凸出X面。

When the cap on a finished lamp has been screwd into the gauge as far as it will go, the centre contact shall be co-planar with, or project beyond , surface X.

E40灯头止规7006-28D-1

Not Go Gauge for E40 Caps on Finished Lamps 7006-28D-1

 目的：

Purpose:

检验成品灯上E40灯头螺纹最小外径（尺寸d）。

To check the minimum outside (major) diameter of the screw thread, dimension d, of E40 caps on finished lamps.

 检验：

Testing:

当量规套在成品灯（灯头向上）的灯头螺纹上时，灯头中心触点不应凸出X面。检验仅利用量规本身的重量进行。

When the gauge is placed over the thread of the cap on a finished lamps, held cap uppermost, the centre contact shall not projeject beyond surface X. Only the weight of the gauge itself shall be used in the test.

E40成品灯接触性能规|7006-52-1

Gauge for Finished Lamp Fitted With E40 Caps for Testing Contact Making|7006-52-1

 图中所示量规处于检验状态。当静止状态时，柱塞应在V面以上。

The gauge is shown in the test position. In the rest position the plunger shall be above plane V.

目的：

Porpose:

检验灯在灯座中有关接触性能的尺寸。

To check lamp dimensions for contact making in IEC holders.

检验：

Testing:

如果灯插入量规时，W面可与V面共面或凸出V面，则可认为灯的形状与灯座的配合是合格的。

The shape of the lamp with regard to the fit in the lampholder is assumed to be correct, if the lamp can be pushed into the gauge till plane W reaches plane V or projects beyond it.

E40防意外接触规 7006-53-1

Gauge for Finished Lamps Fitted with E40 Caps for Testing Protection Against Accidental Contact 7006-53-1

图中所示量规处于检验状态。当静止状态时，柱塞应凸出V面。

The gauge is shown in the test position. In the rest position the plunger shall be above plane V.

目的：

Purpose:

检验防意外接触性能。

To check protection against accidental contact.

检验：

Testing:

如果灯完全插入量规时，W面没有凸出V面，则可认为灯的形状对于防意外接触性能是合格的。

The shape of the lamp with regard to protection against accidental contact is assumed to be correct if the test sample being pushed as far as possible into the gauge, plane W does not protrude beyond plane V.

广东安规检测有限公司设计生产的E40灯头量规一套包含E40灯头通规、E40灯头止规、E40灯头接触性能规、E40灯头防意外接触规，适用于E40螺口灯头的球泡光源的质量检测。

产品完全符合标准IEC60061-3|GB/T1483，100%通过计量检定。

专业安规公司，富有行业经验的专业团队

精选优质材料生产，质量保证。