E12灯头通规：7006-27H-1

E12Go gauge for caps on finished lamps: 7006-27H-1

目的：

PURPOSE:

检验成品灯上E12灯头螺纹最大尺寸和尺寸T1min。

To check the maximum dimension of the screw thread and dimension T1 minimum of E12 caps on finished lamps.

检验：

TESTING:

当成品灯上的灯头完全旋入量规内时，灯头中心触点应与量规X面接触，当从量规中取出时，至少应旋转两圈才能脱离螺纹。

此量规仅与本部分中参数表7006-27J规定的量规配合使用。

When the cap on finished lamps has been screwed into the gauge as far as it will go, the centre contact shall touch surface X. When the lamp is being removed from the gauge, at least two full turns shall be required to disengage the threads. This gauge should be used only in conjunction with the gauge specified on sheet 7006-27J.

E12灯头止规 7006-28C-1

E12 Not Go gauge for caps on finished lamps 7006-28C-1

目的：

PURPOSE:

检验成品灯上E12灯头螺纹最小外径（尺寸d）。

To check the minimum outside (major) diameter of the screw thread, dimensiion d, of E12 caps on finished lamps. 

检验：

TESTING:

当量规套在成品灯（灯头朝上）的灯头螺纹上时，灯头中心触点不应凸出量规的X面。

When the gauge is placed over the thread of the cap on a finished lamp, held cap uppermost, the centre contact shall not project beyond surface X. 检验仅利用量规自身重量进行。

Only the mass of the gauge itself shall be used in the test.

E12灯头接触性能规：7006-32-1 

Gauge for finished lamps fitted with E12 caps：7006-32-1 IEC60061-3|

目的：

PURPOSE:

检验灯与灯座接触的有关尺寸，尤其是灯头长度和玻壳肩部形状的组合尺寸。

To check lamp dimensions, particularly the combination of cap length and bulb shoulder shape, for contact-making in a lampholder.

检验：

TESTING:

将灯插入量规时，W面可以与V面共面或凸出V面，则可以认为灯的形状与灯座的配合是合格的。

The shape of the lamp, with regard to the fit in the lampholder, is assumed to be correct, if the lamp can pushed into the gauge until surface W reaches surface V or project beyond it.

E12灯头附加通规：7006-27J-1

E12 Additional Go gauge for Caps：7006-27J-1

目的：

PURPOSE:

检验成品灯上E12灯头螺纹最大外径（尺寸d）。

To check the maximum outside (major) diameter, dimesion d, of E12 caps on finished lamps.

检验：

TESTING:

当量规套在成品灯的灯头螺纹上时，应能完全通过，所使用的最大力应不超过4.5N.此量规仅与本部分中GB/T1483.1 7006-27H所示的量规配合使用。

The gauge shall pass over the threads of the cap. The maximum force used shall not exeed 4.5N. This gauge should be used only in conjunction with the gauge specified on sheet 7006-27H.

适用于E12螺口灯头的球泡光源的质量检测。

广东安规检测有限公司设计生产的E12灯头量规包含E12灯头通规、E12灯头止规、E12灯头接触性能规、E12灯头附加通规四个，产品完全符合标准IEC60061-3|GB/T1483.1，100%通过计量检定。

专业安规公司，富有行业经验的专业团队

精选优质材料生产，质量保证。